#include <common.h>
#include <twl4030.h>
#include <asm/io.h>
+#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include <asm/mach-types.h>
#include "devkit8000.h"
+#include <asm/gpio.h>
#ifdef CONFIG_DRIVER_DM9000
#include <net.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
+static u32 gpmc_net_config[GPMC_MAX_REG] = {
+ NET_GPMC_CONFIG1,
+ NET_GPMC_CONFIG2,
+ NET_GPMC_CONFIG3,
+ NET_GPMC_CONFIG4,
+ NET_GPMC_CONFIG5,
+ NET_GPMC_CONFIG6,
+ 0
+};
+
/*
* Routine: board_init
* Description: Early hardware init.
return 0;
}
+/* Configure GPMC registers for DM9000 */
+static void gpmc_dm9000_config(void)
+{
+ enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
+ CONFIG_DM9000_BASE, GPMC_SIZE_16M);
+}
+
/*
* Routine: misc_init_r
* Description: Configure board specific parts
twl4030_power_init();
#ifdef CONFIG_TWL4030_LED
- twl4030_led_init();
+ twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
#endif
#ifdef CONFIG_DRIVER_DM9000
/* Configure GPMC registers for DM9000 */
- writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[6].config1);
- writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[6].config2);
- writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[6].config3);
- writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[6].config4);
- writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[6].config5);
- writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[6].config6);
- writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[6].config7);
+ enable_gpmc_cs_config(gpmc_net_config, &gpmc_cfg->cs[6],
+ CONFIG_DM9000_BASE, GPMC_SIZE_16M);
/* Use OMAP DIE_ID as MAC address */
if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
MUX_DEVKIT8000();
}
-#ifdef CONFIG_DRIVER_DM9000
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0, 0, 0, -1, -1);
+}
+#endif
+
+#if defined(CONFIG_DRIVER_DM9000) & !defined(CONFIG_SPL_BUILD)
/*
* Routine: board_eth_init
* Description: Setting up the Ethernet hardware.
return dm9000_initialize(bis);
}
#endif
+
+#ifdef CONFIG_SPL_OS_BOOT
+/*
+ * Do board specific preperation before SPL
+ * Linux boot
+ */
+void spl_board_prepare_for_linux(void)
+{
+ gpmc_dm9000_config();
+}
+
+/*
+ * devkit8000 specific implementation of spl_start_uboot()
+ *
+ * RETURN
+ * 0 if the button is not pressed
+ * 1 if the button is pressed
+ */
+int spl_start_uboot(void)
+{
+ int val = 0;
+ if (!gpio_request(CONFIG_SPL_OS_BOOT_KEY, "U-Boot key")) {
+ gpio_direction_input(CONFIG_SPL_OS_BOOT_KEY);
+ val = gpio_get_value(CONFIG_SPL_OS_BOOT_KEY);
+ gpio_free(CONFIG_SPL_OS_BOOT_KEY);
+ }
+ return !val;
+}
+#endif
+
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on the first bank. This
+ * provides the timing values back to the function that configures
+ * the memory. We have either one or two banks of 128MB DDR.
+ */
+void get_board_mem_timings(struct board_sdrc_timings *timings)
+{
+ /* General SDRC config */
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+
+ /* AC timings */
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+
+ timings->mr = MICRON_V_MR_165;
+}