x86: Add CBMEM console driver for coreboot

[karo-tx-uboot.git] / drivers / misc / ds4510.c

diff --git a/drivers/misc/ds4510.c b/drivers/misc/ds4510.c
index 4cd2fc224987bc8c10c9324dc14b76da8e5d70fa..aa893c35fbbde99dffbbcfcc3e4e73013b5b0427 100644 (file)
--- a/drivers/misc/ds4510.c
+++ b/drivers/misc/ds4510.c
@@ -273,7 +273,7 @@ cmd_tbl_t cmd_ds4510[] = {
 #endif
 };
 
-int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
        static uint8_t chip = CONFIG_SYS_I2C_DS4510_ADDR;
        cmd_tbl_t *c;
@@ -294,8 +294,7 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
        if (!c || !((argc == (c->maxargs)) ||
                (((int)c->cmd == DS4510_CMD_DEVICE) &&
                 (argc == (c->maxargs - 1))))) {
-               printf("Usage:\n%s\n", cmdtp->usage);
-               return 1;
+               return cmd_usage(cmdtp);
        }
 
        /* arg2 used as chip addr and pin number */
@@ -366,14 +365,12 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 #ifdef CONFIG_CMD_DS4510_MEM
        /* Only eeprom, seeprom, and sram commands should make it here */
-       if (strcmp(argv[2], "read") == 0) {
+       if (strcmp(argv[2], "read") == 0)
                rw_func = ds4510_mem_read;
-       } else if (strcmp(argv[2], "write") == 0) {
+       else if (strcmp(argv[2], "write") == 0)
                rw_func = ds4510_mem_write;
-       } else {
-               printf("Usage:\n%s\n", cmdtp->usage);
-               return 1;
-       }
+       else
+               return cmd_usage(cmdtp);
 
        addr = simple_strtoul(argv[3], NULL, 16);
        off += simple_strtoul(argv[4], NULL, 16);
@@ -390,7 +387,7 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 U_BOOT_CMD(
        ds4510, 6,      1,      do_ds4510,
-       "ds4510 - ds4510 eeprom/seeprom/sram/gpio access\n",
+       "ds4510 eeprom/seeprom/sram/gpio access",
        "device [dev]\n"
        "       - show or set current device address\n"
 #ifdef CONFIG_CMD_DS4510_INFO
@@ -404,12 +401,14 @@ U_BOOT_CMD(
        "ds4510 pullup pin 0|1\n"
        "       - disable/enable pullup on specified pin\n"
        "ds4510 nv 0|1\n"
-       "       - make gpio and seeprom writes volatile/non-volatile\n"
+       "       - make gpio and seeprom writes volatile/non-volatile"
 #ifdef CONFIG_CMD_DS4510_RST
+       "\n"
        "ds4510 rstdelay 0-3\n"
-       "       - set reset output delay\n"
+       "       - set reset output delay"
 #endif
 #ifdef CONFIG_CMD_DS4510_MEM
+       "\n"
        "ds4510 eeprom read addr off cnt\n"
        "ds4510 eeprom write addr off cnt\n"
        "       - read/write 'cnt' bytes at EEPROM offset 'off'\n"
@@ -418,7 +417,7 @@ U_BOOT_CMD(
        "       - read/write 'cnt' bytes at SRAM-shadowed EEPROM offset 'off'\n"
        "ds4510 sram read addr off cnt\n"
        "ds4510 sram write addr off cnt\n"
-       "       - read/write 'cnt' bytes at SRAM offset 'off'\n"
+       "       - read/write 'cnt' bytes at SRAM offset 'off'"
 #endif
 );
 #endif /* CONFIG_CMD_DS4510 */