* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/* ------------------------------------------------------------------------- */
+#ifndef __CONFIG_H
+#define __CONFIG_H
-#ifndef _CONFIG_ADS860_H
-#define _CONFIG_ADS860_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
+/* Board type */
+#define CONFIG_ADS 1 /* Old Motorola MPC821/860ADS */
+/* Processor type */
#define CONFIG_MPC860 1
-#define CONFIG_MPC860T 1
-#define CONFIG_ADS 1
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 19200 /* console baudrate */
-#define CONFIG_PCMCIA 1 /* To enable PCMCIA support */
-
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_8XX_XIN 32768 /* 32.768 kHz input frequency */
-#define CFG_8XX_FACT 0x5F6 /* Multiply by 1526 */
- /* MPC8XX_FACT * MPC8XX_XIN = 50 MHz */
-#define CONFIG_8xx_GCLK_FREQ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_BAUDRATE 38400 /* Console baudrate */
#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
- "bootm"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
-
-
-#if 0 /* private command defs */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_I2C | \
- CFG_CMD_IDE | CFG_CMD_PCMCIA)
-#endif
- /* default command defs */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x00100000
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xfff00000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xfe000000
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_IS_IN_FLASH 1
-
-#define CFG_ENV_OFFSET 0x00040000
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#define CONFIG_SYS_8XX_FACT 1526 /* 32.768 kHz crystal on XTAL/EXTAL */
#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_8XX_FACT 12 /* 4 MHz oscillator on EXTCLK */
#endif
-/*-----------------------------------------------------------------------
- * SUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+#define CONFIG_SYS_PLPRCR (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 | SCCR_DFALCD00)
-
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
+#define CONFIG_DRAM_50MHZ 1
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xff010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM 0xfe000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
-
-#define CFG_REMAP_OR_AM 0xff000000 /* OR addr mask */
-#define CFG_PRELIM_OR_AM 0xffe00000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
-
-#ifdef USE_REAL_FLASH_VALUES
-/*
- * These values fit our FADS860T ...
- * The "default" behaviour with 1Mbyte initial doesn't work for us!
- */
-#define CFG_BR0_PRELIM 0x0fe000001 /* Real values for the board */
-#define CFG_OR0_PRELIM 0x0ffe00d34
-#define CFG_BR2_PRELIM 0x000000081
-#define CFG_OR2_PRELIM 0x0ff000800
-#else
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-#endif
-
-/* BCSRx - Board Control and Status Registers */
-/* #define CFG_OR1_REMAP CFG_OR0_REMAP */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CFG_MAMR 0x13a01114
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
-/* values according to the manual */
-#define BCSR0 ((uint) (BCSR_ADDR + 00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
+ * Command line configuration.
*/
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
-#undef CONFIG_IDE_LED /* LED for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
-#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-
-/* #define CFG_ATA_BASE_ADDR 0xFE100000 */
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
-
-
-/* (F)ADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
+#include <config_cmd_default.h>
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVCCON BCSR1_PCCVCC0
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_PCMCIA
+#define CONFIG_CMD_PING
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
+/* This is picked up again in fads.h */
+#define FADS_COMMANDS_ALREADY_DEFINED
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
+#include "../../board/fads/fads.h"
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-#ifdef CONFIG_MPC860T
-/* Interrupt level assignments.
- */
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
- */
-#define NR_8259_INTS 0
-
-/* Machine type
- */
-#define _MACH_8xx (_MACH_ads)
-
-#if 0
-#define CONFIG_DISK_SPINUP_TIME 1000000
-#endif
-#undef CONFIG_DISK_SPINUP_TIME /* usin´ Compact Flash */
-
-
-/* PCMCIA configuration
- */
-#define PCMCIA_MAX_SLOTS 2
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
+#define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-#endif /* _CONFIG_ADS860_H */
+#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff