at91sam9260ek: move board id setup to config header

[karo-tx-uboot.git] / include / configs / CPCI405AB.h

diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index d3763441ef9a1a5c4395c6dd9b038decceead9d4..9122cbd8779ec5a27020b1a44b6c9c3d55d6c193 100644 (file)
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -39,6 +39,8 @@
 #define CONFIG_CPCI405_VER2    1       /* ...version 2                 */
 #define CONFIG_CPCI405AB       1       /* ...and special AB version    */
 
+#define        CONFIG_SYS_TEXT_BASE    0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* call board_early_init_f()    */
 #define CONFIG_MISC_INIT_R      1      /* call misc_init_r()           */
 
@@ -61,7 +63,6 @@
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
 #define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
-#define CONFIG_NET_MULTI       1
 #undef  CONFIG_HAS_ETH1
 
 #define CONFIG_RTC_M48T35A     1               /* ST Electronics M48 timekeeper */
@@ -113,9 +114,6 @@
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt       */
 
 #undef CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size      */
@@ -133,6 +131,12 @@
 #define CONFIG_SYS_MEMTEST_START       0x0400000       /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM  */
 
+#define CONFIG_CONS_INDEX      1       /* Use UART0                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
+
 #undef CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 #define CONFIG_SYS_BASE_BAUD       691200
 
@@ -188,7 +192,7 @@
 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 #define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
 #define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
 
 #define CONFIG_PCI_4xx_PTM_OVERWRITE   1 /* overwrite PTMx settings by env */
 
@@ -380,18 +384,8 @@
 #define CONFIG_SYS_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
 
 #define CONFIG_SYS_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CONFIG_SYS_INIT_RAM_END        0x2000  /* End of used area in RAM             */
-#define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x2000  /* Size of used area in RAM            */
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
 #endif /* __CONFIG_H */