sh: add support for sh7752evb board

[karo-tx-uboot.git] / include / configs / FPS860L.h

diff --git a/include/configs/FPS860L.h b/include/configs/FPS860L.h
index e5f3b606edf1b3a082aa95c046f79a9a265fb1d3..c23711d8a44b0157c28675f7676f81fe909dc6eb 100644 (file)
--- a/include/configs/FPS860L.h
+++ b/include/configs/FPS860L.h
@@ -36,9 +36,11 @@
 #define CONFIG_MPC860          1       /* This is a MPC860 CPU         */
 #define CONFIG_FPS860L         1       /* ...on a FingerPrint Sensor   */
 
-#undef CONFIG_8xx_CONS_SMC1
+#define        CONFIG_SYS_TEXT_BASE    0x40000000
+
 #define        CONFIG_8xx_CONS_SMC2    1       /* Console is on SMC2           */
-#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_SYS_SMC_RXBUFLEN        128
+#define CONFIG_SYS_MAXIDLE     10
 #define CONFIG_BAUDRATE                115200
 
 #define        CONFIG_BOOTCOUNT_LIMIT
@@ -129,9 +131,6 @@
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
 #define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define        CONFIG_SYS_PROMPT_HUSH_PS2      "> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define        CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
@@ -149,8 +148,6 @@
 
 #define        CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -165,9 +162,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
-#define        CONFIG_SYS_INIT_RAM_END 0x2F00  /* End of used area in DPRAM    */
-#define        CONFIG_SYS_GBL_DATA_SIZE        64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define        CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define        CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -216,7 +212,9 @@
 /*-----------------------------------------------------------------------
  * Dynamic MTD partition support
  */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT         "nor0=TQM8xxL-0"
 
 #define MTDPARTS_DEFAULT       "mtdparts=TQM8xxL-0:256k(u-boot),"      \
@@ -426,15 +424,11 @@
                         MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
                         MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define        BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
 #define CONFIG_SCC1_ENET
 
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT       1
+#define CONFIG_OF_BOARD_SETUP  1
+#define CONFIG_HWCONFIG                1
+
 #endif /* __CONFIG_H */