* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_MCF52x2 /* define processor family */
-#define CONFIG_M5282 /* define processor type */
+#define CONFIG_MCF52x2 /* define processor family */
+#define CONFIG_M5282 /* define processor type */
-#define FEC_ENET
+#define CONFIG_MCFTMR
-#define CONFIG_BAUDRATE 19200
-#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT (0)
+#define CONFIG_BAUDRATE 115200
-#define CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */
+#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
-#define CFG_ENV_ADDR 0xffe04000
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_IS_IN_FLASH 1
-
+#define CONFIG_ENV_ADDR 0xffe04000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
/*
* BOOTP options
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+# define CONFIG_MII 1
+# define CONFIG_MII_INIT 1
+# define CONFIG_SYS_DISCOVER_PHY
+# define CONFIG_SYS_RX_ETH_BUFFER 8
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+# define CONFIG_SYS_FEC0_PINMUX 0
+# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
+# define MCFFEC_TOUT_LOOP 50000
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CONFIG_SYS_DISCOVER_PHY
+# define FECDUPLEX FULL
+# define FECSPEED _100BASET
+# else
+# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# endif
+# endif /* CONFIG_SYS_DISCOVER_PHY */
+#endif
#define CONFIG_BOOTDELAY 5
-
-#define CFG_PROMPT "-> "
-#define CFG_LONGHELP /* undef to save memory */
+#ifdef CONFIG_MCFFEC
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif /* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME M5282EVB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "u-boot=u-boot.bin\0" \
+ "load=tftp ${loadaddr) ${u-boot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off ffe00000 ffe3ffff;" \
+ "era ffe00000 ffe3ffff;" \
+ "cp.b ${loadaddr} ffe00000 ${filesize};"\
+ "save\0" \
+ ""
+
+#define CONFIG_SYS_PROMPT "-> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x20000
+#define CONFIG_SYS_LOAD_ADDR 0x20000
-#define CFG_MEMTEST_START 0x400
-#define CFG_MEMTEST_END 0x380000
+#define CONFIG_SYS_MEMTEST_START 0x400
+#define CONFIG_SYS_MEMTEST_END 0x380000
-#define CFG_HZ 1000000
-#define CFG_CLK 64000000
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_CLK 64000000
+/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
+
+#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */
+#define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
-#define CFG_MBAR 0x40000000
-
-#undef CFG_DISCOVER_PHY
-#define CFG_ENET_BD_BASE 0x380000
+#define CONFIG_SYS_MBAR 0x40000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR 0x20000000
-#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_SIZE 4 /* SDRAM size in MB */
-#define CFG_FLASH_BASE 0xffe00000
-#define CFG_INT_FLASH_BASE 0xf0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
+#define CONFIG_SYS_INT_FLASH_BASE 0xf0000000
+#define CONFIG_SYS_INT_FLASH_ENABLE 0x21
/* If M5282 port is fully implemented the monitor base will be behind
* the vector table. */
-/* #define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) */
-#define CFG_MONITOR_BASE 0x20000
-
-#define CFG_MONITOR_LEN 0x20000
-#define CFG_MALLOC_LEN (256 << 10)
-#define CFG_BOOTPARAMS_LEN 64*1024
+#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
+#else
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */
+#endif
+#define CONFIG_SYS_MONITOR_LEN 0x20000
+#define CONFIG_SYS_MALLOC_LEN (256 << 10)
+#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
+#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_SECT 35
-#define CFG_MAX_FLASH_BANKS 1
-#define CFG_FLASH_ERASE_TOUT 10000000
+#define CONFIG_SYS_FLASH_CFI
+#ifdef CONFIG_SYS_FLASH_CFI
+
+# define CONFIG_FLASH_CFI_DRIVER 1
+# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
+# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+# define CONFIG_SYS_FLASH_CHECKSUM
+# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16
-
+#define CONFIG_SYS_CACHELINE_SIZE 16
+
+#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - 4)
+#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM)
+#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+ CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
+ CF_CACR_CEIB | CF_CACR_DBWE | \
+ CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
-
+#define CONFIG_SYS_CS0_BASE 0xFFE00000
+#define CONFIG_SYS_CS0_CTRL 0x00001980
+#define CONFIG_SYS_CS0_MASK 0x001F0001
/*-----------------------------------------------------------------------
* Port configuration
*/
+#define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */
+#define CONFIG_SYS_PADDR 0x0000000
+#define CONFIG_SYS_PADAT 0x0000000
+
+#define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */
+#define CONFIG_SYS_PBDDR 0x0000000
+#define CONFIG_SYS_PBDAT 0x0000000
+
+#define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */
+#define CONFIG_SYS_PCDDR 0x0000000
+#define CONFIG_SYS_PCDAT 0x0000000
+
+#define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */
+#define CONFIG_SYS_PCDDR 0x0000000
+#define CONFIG_SYS_PCDAT 0x0000000
+#define CONFIG_SYS_PEHLPAR 0xC0
+#define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */
+#define CONFIG_SYS_DDRUA 0x05
+#define CONFIG_SYS_PJPAR 0xFF
-#endif /* _CONFIG_M5282EVB_H */
+#endif /* _CONFIG_M5282EVB_H */
projects / karo-tx-uboot.git / blobdiff