Merge branch 'master' of git://git.denx.de/u-boot-samsung

[karo-tx-uboot.git] / include / configs / ML2.h

diff --git a/include/configs/ML2.h b/include/configs/ML2.h
index 190239732531335f3a19dfcc5806ff7b011624a8..1e96b9e10e2ece436df65e758d7b8626d3f21164 100644 (file)
--- a/include/configs/ML2.h
+++ b/include/configs/ML2.h
@@ -30,6 +30,7 @@
 #define CONFIG_4xx             1       /* ...member of PPC4xx family   */
 #define CONFIG_ML2     1       /* ...on a ML2 board    */
 
+#define        CONFIG_SYS_TEXT_BASE    0x18000000
 
 #define CONFIG_ENV_IS_IN_FLASH     1
 
@@ -52,16 +53,6 @@
 
 #define CONFIG_PREBOOT         "fsload 0x00100000 /boot/image"
 
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#if 0
-#define CONFIG_SERIAL_SOFTWARE_FIFO 4000
-#else
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#endif
-
 #if 0
 #define CONFIG_BOOTARGS                "root=/dev/nfs "                        \
     "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
@@ -97,6 +88,7 @@
 #define CONFIG_CMD_JFFS2
 
 #undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
 #undef CONFIG_CMD_RTC
 #undef CONFIG_CMD_PCI
 #undef CONFIG_CMD_I2C
@@ -108,6 +100,14 @@
 
 #define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */
 
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C                        /* I2C with hardware support    */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
+#define CONFIG_SYS_I2C_SLAVE   0x7F
+#define CONFIG_SYS_I2C_SPEED   400000
+
 /*
  * Miscellaneous configurable options
  */
@@ -220,9 +220,8 @@
  */
 
 #define CONFIG_SYS_INIT_RAM_ADDR       0x800000  /* inside of SDRAM                     */
-#define CONFIG_SYS_INIT_RAM_END        0x2000  /* End of used area in RAM             */
-#define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE        0x2000  /* Size of used area in RAM             */
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -231,14 +230,6 @@
  */
 #define SPD_EEPROM_ADDRESS      0x50
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
@@ -249,7 +240,7 @@
  *
  */
 /* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV               "nor0"
 #define CONFIG_JFFS2_PART_SIZE         0xFFFFFFFF
 #define CONFIG_JFFS2_PART_OFFSET       0x00080000
@@ -257,7 +248,7 @@
 /* mtdparts command line support */
 /* Note: fake mtd_id used, no linux mtd map file */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT         "nor0=ml2-0"
 #define MTDPARTS_DEFAULT       "mtdparts=ml2-0:-@512k(jffs2)"
 */