DEBUG: Fix debug macros

[karo-tx-uboot.git] / include / configs / MPC832XEMDS.h

diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 68ff191667e53fb0c022e942ab5167fe4a4a9bfd..823b9f127ee96cbc9181e227bc25a811e94d3d4a 100644 (file)
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -28,8 +28,8 @@
 #define CONFIG_MPC83xx         1       /* MPC83xx family */
 #define CONFIG_MPC832x         1       /* MPC832x CPU specific */
 #define CONFIG_MPC832XEMDS     1       /* MPC832XEMDS board specific */
-#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
-#undef CONFIG_PQ_MDS_PIB_ATM   /* QOC3 ATM card */
+
+#define        CONFIG_SYS_TEXT_BASE    0xFE000000
 
 /*
  * System Clock Setup
@@ -135,7 +135,7 @@
 /*
  * The reserved memory
  */
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
@@ -152,9 +152,8 @@
  */
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xE6000000      /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END        0x1000          /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE       0x100           /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000          /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
  * Local Bus Configuration & Clock Setup
@@ -273,7 +272,6 @@
  * Serial Port
  */
 #define CONFIG_CONS_INDEX      1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -334,7 +332,6 @@
 
 #ifdef CONFIG_PCI
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP         /* do pci plug-and-play */
 #define CONFIG_83XX_PCI_STREAMING
 
@@ -344,11 +341,6 @@
 
 #endif /* CONFIG_PCI */
 
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 /*
  * QE UEC ethernet configuration
  */
@@ -363,7 +355,7 @@
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK10
 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       3
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE MII
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED        100
 #endif
 
@@ -375,7 +367,7 @@
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK8
 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       4
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE MII
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED        100
 #endif
 
@@ -447,10 +439,10 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ           (8 << 20)       /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ           (256 << 20)     /* Initial Memory map for Linux */
 
 /*
  * Core HID Setup
@@ -527,14 +519,6 @@
 #define CONFIG_SYS_DBAT7U      CONFIG_SYS_IBAT7U
 #endif
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01    /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02    /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */