Merge branch 'master' of git://git.denx.de/u-boot-ti

[karo-tx-uboot.git] / include / configs / MPC8544DS.h

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 59cfde6284b047f6a79d2c7e8238dc7761b0a556..d1ac32f4ada9a0bfcc2429dac505dc7f0e4d9d64 100644 (file)
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -44,18 +44,12 @@
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
+#define CONFIG_E1000           1       /* Defind e1000 pci Ethernet card*/
 
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_INTERRUPTS              /* enable pci, srio, ddr interrupts */
 
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the CDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
@@ -85,11 +79,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
-#define CONFIG_SYS_PCI1_ADDR           (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR          (CONFIG_SYS_CCSRBAR+0xa000)
-#define CONFIG_SYS_PCIE2_ADDR          (CONFIG_SYS_CCSRBAR+0x9000)
-#define CONFIG_SYS_PCIE3_ADDR          (CONFIG_SYS_CCSRBAR+0xb000)
-
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -192,6 +181,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VCFGEN0          0x12    /* VELA Config Enable 0 */
 #define PIXIS_VCFGEN1          0x13    /* VELA Config Enable 1 */
 #define PIXIS_VBOOT            0x16    /* VELA VBOOT Register */
+#define PIXIS_VBOOT_FMAP       0x80    /* VBOOT - CFG_FLASHMAP */
+#define PIXIS_VBOOT_FBANK      0x40    /* VBOOT - CFG_FLASHBANK */
 #define PIXIS_VSPEED0          0x17    /* VELA VSpeed 0 */
 #define PIXIS_VSPEED1          0x18    /* VELA VSpeed 1 */
 #define PIXIS_VCLKH            0x19    /* VELA VCLKH register */
@@ -246,9 +237,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_BOARD_SETUP          1
 #define CONFIG_OF_STDOUT_VIA_ALIAS     1
 
-#define CONFIG_SYS_64BIT_STRTOUL               1
-#define CONFIG_SYS_64BIT_VSPRINTF              1
-
 /* I2C */
 #define CONFIG_FSL_I2C         /* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C                /* I2C with hardware support */
@@ -340,12 +328,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #define CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)           (x)
-#define _IO_BASE       0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
        #define PCI_ENET0_IOADDR        CONFIG_SYS_PCI1_IO_BUS
        #define PCI_ENET0_MEMADDR       CONFIG_SYS_PCI1_IO_BUS
@@ -433,10 +415,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
-    #define CONFIG_CMD_BEDBUG
     #define CONFIG_CMD_NET
     #define CONFIG_CMD_SCSI
     #define CONFIG_CMD_EXT2
@@ -449,7 +431,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -464,10 +447,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions