#define CONFIG_MPC834x 1
#define CONFIG_MPC8343 1
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000
+
#define CONFIG_SYS_IMMR 0xE0000000
#define CONFIG_PCI
-#define CONFIG_83XX_GENERIC_PCI
#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_HARD_I2C
#define CONFIG_TSEC_ENET
#define CONFIG_MPC8XXX_SPI
#define CONFIG_HARD_SPI
#define MVBLM7_MMC_CS 0x04000000
+#define CONFIG_MISC_INIT_R
/* I2C */
-#undef CONFIG_SOFT_I2C
-
#define CONFIG_FSL_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* DDR Setup
*/
+#undef CONFIG_SPD_EEPROM
+
#define CONFIG_SYS_DDR_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0 1
#define CONFIG_SYS_MEMTEST_START (60<<20)
#define CONFIG_SYS_MEMTEST_END (70<<20)
+#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDRCDR (DDRCDR_PZ_HIZ \
+ | DDRCDR_NZ_HIZ \
+ | DDRCDR_Q_DRN)
+ /* 0x22000001 */
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_DDR_SIZE 256
+#define CONFIG_SYS_DDR_SIZE 512
-/* HC, 75Ohm, DDR-II, DRQ */
-#define CONFIG_SYS_DDRCDR 0x80000001
-/* EN, ODT_WR, 3BA, 14row, 10col */
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014102
-#define CONFIG_SYS_DDR_CS1_CONFIG 0x0
-#define CONFIG_SYS_DDR_CS2_CONFIG 0x0
-#define CONFIG_SYS_DDR_CS3_CONFIG 0x0
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
-#define CONFIG_SYS_DDR_CS1_BNDS 0x0
-#define CONFIG_SYS_DDR_CS2_BNDS 0x0
-#define CONFIG_SYS_DDR_CS3_BNDS 0x0
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x3837c322
+#define CONFIG_SYS_DDR_TIMING_2 0x0f9848c6
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x2625b221
-#define CONFIG_SYS_DDR_TIMING_2 0x1f9820c7
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-/* ~MEM_EN, SREN, DDR-II, 32_BE */
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080000
+#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080008
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_INTERVAL 0x04060100
+#define CONFIG_SYS_DDR_INTERVAL 0x02000100
-#define CONFIG_SYS_DDR_MODE 0x078e0232
+#define CONFIG_SYS_DDR_MODE 0x04040242
+#define CONFIG_SYS_DDR_MODE2 0x00800000
/* Flash */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_FLASH_SIZE 8
-#define CONFIG_SYS_FLASH_SIZE_SHIFT 3
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
#define CONFIG_SYS_FLASH_WRITE_TOUT 500
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 256
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS|\
- OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | \
- OR_GPCM_EAD)
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
+ | BR_PS_16 \
+ | BR_MS_GPCM \
+ | BR_V)
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX_SET \
+ | OR_GPCM_EHTR_SET \
+ | OR_GPCM_EAD)
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | (0x13 + CONFIG_SYS_FLASH_SIZE_SHIFT))
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
/*
* U-Boot memory configuration
*/
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#undef CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/* LB sdram refresh timer, about 6us */
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_CONSOLE ttyS0
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI1_MMIO_BASE \
+ (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000
-#define CONFIG_NET_MULTI 1
#define CONFIG_NET_RETRY_COUNT 3
-#define PCI_66M
+#define CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN 66666667
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_FEC1_PHY_NORXERR
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define TSEC1_PHY_ADDR 0x10
#define TSEC1_PHYIDX 0
#define TSEC1_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
#define CONFIG_HAS_ETH1
-#define CONFIG_TSEC2_NAME "TSEC1"
+#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_FEC2_PHY_NORXERR
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
#define TSEC2_PHY_ADDR 0x11
#define TSEC2_PHYIDX 0
#define TSEC2_FLAGS (TSEC_GIGABIT|TSEC_REDUCED)
#define CONFIG_BOOTP_SEND_HOSTNAME
/* USB */
+#define CONFIG_SYS_USB_HOST
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* Environment
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_LOADS_ECHO
#define CONFIG_SYS_LOADS_BAUD_CHANGE
#define CONFIG_CMD_PCI
#define CONFIG_CMD_I2C
#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_USB
+#define CONFIG_DOS_PARTITION
#undef CONFIG_WATCHDOG
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x2000000
#define CONFIG_SYS_PROMPT "mvBL-M7> "
#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ 1000
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+ /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_HRCW_LOW 0x0
#define CONFIG_SYS_HRCW_HIGH 0x0
* System performance
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
#define CONFIG_SYS_SCCR_TSEC1CM 1
#define CONFIG_SYS_SCCR_TSEC2CM 1
-#define CONFIG_SYS_SICRH 0x1fff8003
+#define CONFIG_SYS_SICRH 0x1fef0003
#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0)
#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL CONFIG_SYS_HID0_INIT
+#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \
+ HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1
/* DDR */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* PCI */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* no PCI2 */
#define CONFIG_SYS_IBAT3L 0
#define CONFIG_SYS_IBAT4U 0
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
+ | BATL_PP_RW \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L (0xF0000000 \
+ | BATL_PP_RW \
+ | BATL_MEMCOHERENCE \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (0xF0000000 \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#define CONFIG_SYS_IBAT7L 0
#define CONFIG_SYS_IBAT7U 0
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
/*
* Environment Configuration
*/
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY 1000
-#define MV_CI mvBL-M7
-#define MV_VCI mvBL-M7
-#define MV_FPGA_DATA 0xfff80000
-#define MV_FPGA_SIZE 0x00076ca2
+#define MV_CI "mvBL-M7"
+#define MV_VCI "mvBL-M7"
+#define MV_FPGA_DATA 0xfff40000
+#define MV_FPGA_SIZE 0
#define MV_KERNEL_ADDR 0xff810000
#define MV_INITRD_ADDR 0xffb00000
-#define MV_SOURCE_ADDR 0xff804000
-#define MV_SOURCE_ADDR2 0xff806000
+#define MV_SCRIPT_ADDR 0xff804000
+#define MV_SCRIPT_ADDR2 0xff806000
#define MV_DTB_ADDR 0xff808000
#define MV_INITRD_LENGTH 0x00400000
#define MV_DTB_ADDR_RAM 0x00600000
#define MV_INITRD_ADDR_RAM 0x01000000
-#define CONFIG_BOOTCOMMAND "if imi ${autoscr_addr}; \
- then source ${autoscr_addr}; \
- else source ${autoscr_addr2}; \
- fi;"
+#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; " \
+ "then source ${script_addr}; " \
+ "else source ${script_addr2}; " \
+ "fi;"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0" \
- "baudrate=" MK_STR(CONFIG_BAUDRATE) "\0" \
+ "baudrate=" __stringify(CONFIG_BAUDRATE) "\0" \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"fpga=0\0" \
- "fpgadata=" MK_STR(MV_FPGA_DATA) "\0" \
- "fpgadatasize=" MK_STR(MV_FPGA_SIZE) "\0" \
- "autoscr_addr=" MK_STR(MV_SOURCE_ADDR) "\0" \
- "autoscr_addr2=" MK_STR(MV_SOURCE_ADDR2) "\0" \
- "mv_kernel_addr=" MK_STR(MV_KERNEL_ADDR) "\0" \
- "mv_kernel_addr_ram=" MK_STR(MV_KERNEL_ADDR_RAM) "\0" \
- "mv_initrd_addr=" MK_STR(MV_INITRD_ADDR) "\0" \
- "mv_initrd_addr_ram=" MK_STR(MV_INITRD_ADDR_RAM) "\0" \
- "mv_initrd_length=" MK_STR(MV_INITRD_LENGTH) "\0" \
- "mv_dtb_addr=" MK_STR(MV_DTB_ADDR) "\0" \
- "mv_dtb_addr_ram=" MK_STR(MV_DTB_ADDR_RAM) "\0" \
- "dtb_name=" MK_STR(MV_DTB_NAME) "\0" \
+ "fpgadata=" __stringify(MV_FPGA_DATA) "\0" \
+ "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \
+ "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \
+ "script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \
+ "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \
+ "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \
+ "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \
+ "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \
+ "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \
+ "mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \
+ "mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \
+ "dtb_name=" __stringify(MV_DTB_NAME) "\0" \
"mv_version=" U_BOOT_VERSION "\0" \
- "dhcp_client_id=" MK_STR(MV_CI) "\0" \
- "dhcp_vendor-class-identifier=" MK_STR(MV_VCI) "\0" \
+ "dhcp_client_id=" MV_CI "\0" \
+ "dhcp_vendor-class-identifier=" MV_VCI "\0" \
"netretry=no\0" \
"use_static_ipaddr=no\0" \
"static_ipaddr=192.168.90.10\0" \
"static_netmask=255.255.255.0\0" \
"static_gateway=0.0.0.0\0" \
- "initrd_name=uInitrd.mvblm7-xenorfs\0" \
+ "initrd_name=uInitrd.mvBL-M7-rfs\0" \
"zcip=no\0" \
"netboot=yes\0" \
"mvtest=Ff\0" \
""
#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA CONFIG_SYS_ALTERA_CYCLON2
+#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
projects / karo-tx-uboot.git / blobdiff