#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#endif
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_SYS_PCIE2_NAME "PCIe Slot"
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_PCIE2_NAME "mini PCIe Slot"
+#endif
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1010 RDB */
#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */
-#ifndef CONFIG_SDCARD
#define CONFIG_MISC_INIT_R
-#endif
-
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#endif
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-
#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
#define CONFIG_SYS_DDR_RCW_1 0x00000000
#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0x470C0000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x04401010
+#define CONFIG_SYS_DDR_CONTROL 0xc70c0008 /* Type = DDR3 */
+#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
#define CONFIG_SYS_DDR_TIMING_4 0x00000001
#define CONFIG_SYS_DDR_TIMING_5 0x03402400
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4644
+#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
+#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
+#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF
#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800 0x40461520
-#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
+#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
+#define CONFIG_SYS_DDR_MODE_2_800 0x00000000
#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
/* settings for DDR3 at 667MT/s */
#define CONFIG_SYS_DDR_TIMING_3_667 0x00010000
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
-/* In case of SD card boot, IFC interface is not available because of muxing */
-#ifdef CONFIG_SDCARD
-#define CONFIG_SYS_NO_FLASH
-#else
/*
* IFC Definitions
*/
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#endif
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITION
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nand0=ff800000.flash"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
+
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_NAND \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
+ | CSOR_NAND_PB(128)) /*Pages Per Block = 128 */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
+#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+#if defined(CONFIG_P1010RDB_PA)
/* NAND Flash Timing Params */
#define CONFIG_SYS_NAND_FTIM0 FTIM0_NAND_TCCST(0x01) | \
FTIM0_NAND_TWP(0x0C) | \
FTIM2_NAND_TWHRE(0x0f)
#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
+#elif defined(CONFIG_P1010RDB_PB)
+/* support MT29F16G08ABABAWP 4k-pagesize 2G-bytes NAND */
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07)| \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32)| \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+#endif
+
#define CONFIG_SYS_NAND_DDR_LAW 11
/* Set up IFC registers for boot location NOR/NAND */
FTIM2_GPCM_TCH(0x0) | \
FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3 0x0
-#endif /* CONFIG_SDCARD */
#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#define I2C_PCA9557_ADDR1 0x18
+#define I2C_PCA9557_ADDR2 0x19
+#define I2C_PCA9557_BUS_NUM 0
/* I2C EEPROM */
-#undef CONFIG_ID_EEPROM
+#if defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define MAX_NUM_PORTS 9 /* for 128Bytes EEPROM */
+#endif
/* enable read and write access to EEPROM */
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_LBA48
#endif /* #ifdef CONFIG_FSL_SATA */
-/* SD interface will only be available in case of SD boot */
-#ifdef CONFIG_SDCARD
#define CONFIG_MMC
-#define CONFIG_DEF_HWCONFIG esdhc
-#endif
-
#ifdef CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_NAND)
#define CONFIG_ENV_IS_IN_NAND
+#if defined(CONFIG_P1010RDB_PA)
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_ENV_RANGE (32 * CONFIG_ENV_SIZE) /* new block size 512K */
+#endif
#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */
/*
* Internal Definitions
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
#define CONFIG_HAS_ETH2
#endif
-#define CONFIG_HOSTNAME P1010RDB
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
"ext2load usb 0:4 $loadaddr $bootfile;" \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ CONFIG_BOOTMODE
+
+#if defined(CONFIG_P1010RDB_PA)
+#define CONFIG_BOOTMODE \
+ "boot_bank0=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00009 0; reset\0" \
+ "boot_bank1=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00009 1; reset\0" \
+ "boot_nand=i2c dev 0; i2c mw 18 1 f9; i2c mw 18 3 f0;" \
+ "mw.b ffb00011 0; mw.b ffb00017 1; reset\0"
+
+#elif defined(CONFIG_P1010RDB_PB)
+#define CONFIG_BOOTMODE \
+ "boot_bank0=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+ "i2c mw 19 1 2; i2c mw 19 3 e1; reset\0" \
+ "boot_bank1=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
+ "i2c mw 19 1 12; i2c mw 19 3 e1; reset\0" \
+ "boot_nand=i2c dev 0; i2c mw 18 1 fc; i2c mw 18 3 0;" \
+ "i2c mw 19 1 8; i2c mw 19 3 f7; reset\0" \
+ "boot_spi=i2c dev 0; i2c mw 18 1 fa; i2c mw 18 3 0;" \
+ "i2c mw 19 1 0; i2c mw 19 3 f7; reset\0" \
+ "boot_sd=i2c dev 0; i2c mw 18 1 f8; i2c mw 18 3 0;" \
+ "i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
+#endif
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-#ifdef CONFIG_SECURE_BOOT
#include <asm/fsl_secure_boot.h>
-#endif
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff