***********************************************************/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-/***********************************************************
- * Command definitions
- ***********************************************************/
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_IDE | \
- CFG_CMD_DHCP | \
- CFG_CMD_PCI | \
- CFG_CMD_CACHE | \
- CFG_CMD_IRQ | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_REGINFO | \
- CFG_CMD_FDC | \
- CFG_CMD_SCSI | \
- CFG_CMD_FAT | \
- CFG_CMD_DATE | \
- CFG_CMD_ELF | \
- CFG_CMD_USB | \
- CFG_CMD_MII | \
- CFG_CMD_SDRAM | \
- CFG_CMD_DOC | \
- CFG_CMD_PING | \
- CFG_CMD_SAVES | \
- CFG_CMD_BSP )
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FDC
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_DOC
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_BSP
+
+
+#define CONFIG_NAND_LEGACY
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
***************************************************************/
#define SPD_EEPROM_ADDRESS 0x50
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
/**************************************************************
* Environment definitions
**************************************************************/
#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
-#define CONFIG_BOOT_RETRY_TIME -10 /* feature is avaiable but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
**********************************************************/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
/*
* For booting Linux, the board info and command line data
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Init Memory Controller:
*/
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF4000000
#define CFG_TEMP_STACK_OCM 1
#define CFG_OCM_DATA_ADDR 0xF0000000
#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
***********************************************************/
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-#define CONFIG_CS8952_PHY 1 /* its a CS8952 PHY */
/************************************************************
* RTC
***********************************************************/
/************************************************************
* Debug support
************************************************************/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+/************************************************************
+ * support BZIP2 compression
+ ************************************************************/
+#define CONFIG_BZIP2 1
+
/************************************************************
* Ident
************************************************************/
projects / karo-tx-uboot.git / blobdiff