#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_PLU405 1 /* ...on a PLU405 board */
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_NET_MULTI 1
#undef CONFIG_HAS_ETH1
+#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_SUPPORT_VFAT
-#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
#define CONFIG_SYS_BASE_BAUD 691200
-#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
* NAND-FLASH stuff
*/
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
-#define NAND_MAX_CHIPS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFFA0000
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserve 384kB for malloc() */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
+#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
/*
* Environment Variable setup
* I2C EEPROM (24WC16) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* External Bus Controller (EBC) Setup
*/
-#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define CAN0_BA 0xF0000000 /* CAN0 Base Address */
+#define CAN1_BA 0xF0000100 /* CAN1 Base Address */
#define DUART0_BA 0xF0000400 /* DUART Base Address */
#define DUART1_BA 0xF0000408 /* DUART Base Address */
#define RTC_BA 0xF0000500 /* RTC Base Address */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CONFIG_SYS_GPIO0_OSRH 0x00000550
-#define CONFIG_SYS_GPIO0_OSRL 0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H 0x00000000
-#define CONFIG_SYS_GPIO0_ISR1L 0x15555445
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_OSRL 0x00000550
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
#define CONFIG_SYS_GPIO0_TCR 0x77FE0014
#define CONFIG_SYS_DUART_RST (0x80000000 >> 14)
#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0)
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
/*
* Default speed selection (cpu_plb_opb_ebc) in MHz.
* This value will be set if iic boot eprom is disabled.
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
#define CONFIG_USB_STORAGE 1
+/*
+ * UBI
+ */
+#define CONFIG_CMD_UBI
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff