/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com.
* Based on the sequoia configuration file.
*
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF90000
+#endif
+
#define CONFIG_SYS_CLK_FREQ 33333400
#if 0 /* temporary disabled because OS/9 does not like dcache on startup */
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_MISC_INIT_F 1
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_TYPES 1 /* support board types */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */
#define CONFIG_PRAM 0 /* use pram variable to overwrite */
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
-#define CFG_OCM_BASE 0xe0010000 /* ocm */
-#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
-#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-#define CFG_PCI_MEMSIZE 0x80000000 /* 2GB! */
-
-/* Don't change either of these */
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-
-#define CFG_USB2D0_BASE 0xe0000100
-#define CFG_USB_DEVICE 0xe0000000
-#define CFG_USB_HOST 0xe0000400
-#define CFG_FPGA_BASE0 0xef000000 /* 32 bit */
-#define CFG_FPGA_BASE1 0xef100000 /* 16 bit */
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */
+#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+#define CONFIG_SYS_PCI_MEMSIZE 0x80000000 /* 2GB! */
+
+#define CONFIG_SYS_USB2D0_BASE 0xe0000100
+#define CONFIG_SYS_USB_DEVICE 0xe0000000
+#define CONFIG_SYS_USB_HOST 0xe0000400
+#define CONFIG_SYS_FPGA_BASE0 0xef000000 /* 32 bit */
+#define CONFIG_SYS_FPGA_BASE1 0xef100000 /* 16 bit */
+#define CONFIG_SYS_RESET_BASE 0xef200000
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-#undef CONFIG_UART1_CONSOLE /* console on front panel */
+#define CONFIG_SERIAL_MULTI 1
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*-----------------------------------------------------------------------
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
-#ifdef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
#endif
/*
* the NAND controller. sr - 2006-08-25
*/
#if defined (CONFIG_NAND_U_BOOT)
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
-
-#define CFG_NAND_ECCSIZE 256
-#define CFG_NAND_ECCBYTES 3
-#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
-#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 16
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#endif
-#ifdef CFG_ENV_IS_IN_NAND
+#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM (256) /* 256MB */
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+ /* 440EPx errata CHIP 11 */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_I2C_CMD_TREE 1
#define CONFIG_I2C_MULTI_BUS 1
-#define CFG_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR 0x54
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 5
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CFG_EEPROM_WREN 1
-#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
+#define CONFIG_SYS_EEPROM_WREN 1
+#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
/*
* standard dtt sensor configuration - bottom bit will determine local or
* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
*/
#define CONFIG_DTT_ADM1021
-#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
+#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
-#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \
+ "\\\"painit\\\" to preboot command"
#undef CONFIG_BOOTARGS
/* Setup some board specific values for the default environment variables */
#define CONFIG_HOSTNAME pmc440
-#define CFG_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0"
+#define CONFIG_SYS_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0"
+#define CONFIG_SYS_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
+ CONFIG_SYS_BOOTFILE \
+ CONFIG_SYS_ROOTPATH \
+ "fdt_file=/tftpboot/pmc440/pmc440.dtb\0" \
"netdev=eth0\0" \
"ethrotate=no\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "kernel_addr=FC000000\0" \
- "ramdisk_addr=FC180000\0" \
+ "addmisc=setenv bootargs ${bootargs} mem=${mem}\0" \
+ "nandargs=setenv bootargs root=/dev/mtdblock6 rootfstype=jffs2 rw\0" \
+ "nand_boot_fdt=run nandargs addip addtty addmisc;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_nfs_fdt=tftp ${kernel_addr_r} ${bootfile};" \
+ "tftp ${fdt_addr_r} ${fdt_file};" \
+ "run nfsargs addip addtty addmisc;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "kernel_addr=ffc00000\0" \
+ "kernel_addr_r=200000\0" \
+ "fpga_addr=fff00000\0" \
+ "fdt_addr=fff80000\0" \
+ "fdt_addr_r=800000\0" \
+ "fpga=fpga loadb 0 ${fpga_addr}\0" \
"load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \
- "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
- "cp.b 200000 FFFA0000 60000\0" \
+ "update=protect off fff90000 ffffffff;era fff90000 ffffffff;" \
+ "cp.b 200000 fff90000 70000\0" \
""
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_PPC4xx_EMAC
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_RESET_PHY_R 1
/* USB */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
-#define CFG_OHCI_BE_CONTROLLER
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CFG_USB_OHCI_BOARD_INIT 1
-#define CFG_USB_OHCI_CPU_INIT 1
-#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
-#define CFG_USB_OHCI_SLOT_NAME "ppc440"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_UART | \
- CFG_POST_I2C | \
- CFG_POST_CACHE | \
- CFG_POST_FPU | \
- CFG_POST_ETHER | \
- CFG_POST_SPR)
-
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
-
-/* esd expects pram at end of physical memory.
- * So no logbuffer at the moment.
- */
-#if 0
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_FPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_SPR)
+
#define CONFIG_LOGBUFFER
-#endif
-#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#define CONFIG_SUPPORT_VFAT
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Press SPACE to abort autoboot in %d seconds\n", bootdelay
#undef CONFIG_AUTOBOOT_DELAY_STR
#define CONFIG_AUTOBOOT_STOP_STR " "
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
+#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
+
+#define CONFIG_PCI_BOOTDELAY 0
/* PCI identification */
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */
-#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */
-#define CFG_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC
-#define CFG_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */
+#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */
+/* for weak __pci_target_init() */
+#define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH
+#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC
+#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FPGA stuff
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_NAND_CS 2 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x03017200
-#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB0AP 0x03017200
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 2 (NAND-FLASH) initialization */
-#define CFG_EBC_PB2AP 0x018003c0
-#define CFG_EBC_PB2CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB2AP 0x018003c0
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#else
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 2 (NOR-FLASH) initialization */
-#define CFG_EBC_PB2AP 0x03017200
-#define CFG_EBC_PB2CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB2AP 0x03017200
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#endif
+/* Memory Bank 1 (RESET) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_RESET_BASE | 0x1c000)
+
/* Memory Bank 4 (FPGA / 32Bit) initialization */
-#define CFG_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */
-#define CFG_EBC_PB4CR (CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */
+#define CONFIG_SYS_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */
+#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */
/* Memory Bank 5 (FPGA / 16Bit) initialization */
-#define CFG_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */
-#define CFG_EBC_PB5CR (CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */
+#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#define CFG_NAND_QUIET_TEST 1
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_NAND_QUIET_TEST 1
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_API 1
+
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff