*/
/* #define DEBUG 1 */
+/* #define DEPLOYMENT 1 */
#undef CONFIG_MPC860
#define CONFIG_MPC823 1 /* This is a MPC823e CPU. */
#define CONFIG_RPXLITE 1 /* RPXlite DW version board */
+#define CONFIG_SYS_TEXT_BASE 0xff000000
+
#ifdef CONFIG_LCD /* with LCD controller ? */
+#define CONFIG_MPC8XX_LCD
#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/
#endif
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 9600 /* console default baudrate = 9600bps */
-#ifdef CONFIG_LCD
-#define CONFIG_BOOTDELAY 12 /* autoboot after 12 seconds */
-#else
+#ifdef DEBUG
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#endif
+#else
+#define CONFIG_BOOTDELAY 6 /* autoboot after 6 seconds */
+
+#ifdef DEPLOYMENT
+#define CONFIG_BOOT_RETRY_TIME -1
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT \
+ "autoboot in %d seconds (stop with 'st')...\n", bootdelay
+#define CONFIG_AUTOBOOT_STOP_STR "st"
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_RESET_TO_RETRY 1
+#define CONFIG_BOOT_RETRY_MIN 1
+#endif /* DEPLOYMENT */
+#endif /* DEBUG */
+
+/* pre-boot commands */
+#define CONFIG_PREBOOT "setenv stdout serial;setenv stdin serial"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
- "nfsargs=setenv bootargs console=ttyS0,9600 root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ramargs=setenv bootargs console=tty0 console=ttyS0,9600 " \
- "root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "nfsargs=setenv bootargs console=tty0 console=ttyS0,9600 " \
+ "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs console=tty0 root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"gatewayip=172.16.115.254\0" \
"netmask=255.255.255.0\0" \
- "kernel_addr=ff880000\0" \
- "ramdisk_addr=ff980000\0" \
- ""
+ "kernel_addr=ff040000\0" \
+ "ramdisk_addr=ff200000\0" \
+ "ku=era ${kernel_addr} ff1fffff;cp.b 100000 ${kernel_addr} " \
+ "${filesize};md ${kernel_addr};" \
+ "echo kernel updating finished\0" \
+ "uu=protect off 1:0-4;era 1:0-4;cp.b 100000 ff000000 " \
+ "${filesize};md ff000000;" \
+ "echo u-boot updating finished\0" \
+ "eu=protect off 1:6;era 1:6;reset\0" \
+ "lcd=setenv stdout lcd;setenv stdin lcd\0" \
+ "ser=setenv stdout serial;setenv stdin serial\0" \
+ "verify=no"
+
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_STATUS_LED /* disturbs display. Status LED disabled. */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+#if 1 /* Enable this stuff could make image enlarge about 25KB. Mask it if you
+ don't want the advanced function */
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#endif
+
+
+/* test-only */
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+
+#define CONFIG_NETCONSOLE
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#endif /* 1 */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "u-boot>" /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "u-boot>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0040000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* Low Level Configuration Settings
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFA200000
+#define CONFIG_SYS_IMMR 0xFA200000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE)
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#if defined(DEBUG) || defined(CONFIG_CMD_IDE)
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
-#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
#endif
-#define CFG_MONITOR_BASE 0xFF000000
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+#define CONFIG_SYS_MONITOR_BASE 0xFF000000
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#ifdef CFG_ENV_IS_IN_NVRAM
-#define CFG_ENV_ADDR 0xFA000100
-#define CFG_ENV_SIZE 0x1000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#ifdef CONFIG_ENV_IS_IN_NVRAM
+#define CONFIG_ENV_ADDR 0xFA000100
+#define CONFIG_ENV_SIZE 0x1000
#else
-#define CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */
-#endif
-
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */
+#define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */
+#endif /* CONFIG_ENV_IS_IN_NVRAM */
+#define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res)))
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
-#define CFG_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif /* We can get SYPCR: 0xFFFF0689. */
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
-#define CFG_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */
+#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */
/*---------------------------------------------------------------------
* TBSCR - Time Base Status and Control 16-bit 12-16
*---------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
/* TBSCR: 0x00C3 [SAM] */
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* [RTC enabled but not stopped on FRZ]
*/
-#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 16-bit 12-23
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
* [Periodic timer enabled,Periodic timer interrupt disable. ]
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 32-bit 5-7
*/
/* up to 64 MHz we use a 1:2 clock */
#if defined(RPXlite_64MHz)
-#define CFG_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */
+#define CONFIG_SYS_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */
#else
-#define CFG_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
+#define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
#endif
/*-----------------------------------------------------------------------
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF00
-/* Up to 64MHz system clock, we use 1:2 SYSTEM/BUS ratio */
-#define CFG_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */
+/* Up to 48MHz system clock, we use 1:1 SYSTEM/BUS ratio */
+#if defined(RPXlite_64MHz)
+#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */
+#else
+#define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF00 ) /* %%%SCCR:0x02000000 */
+#endif
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*/
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0100
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
* BR0 and OR0 (FLASH)
*/
#define FLASH_BASE_PRELIM 0xFC000000 /* FLASH base */
-#define CFG_PRELIM_OR_AM 0xFC000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFC000000 /* OR addr mask */
/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 8, ETHR = 0, BIH = 1 */
-#define CFG_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI)
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
/*
* BR1 and OR1 (SDRAM)
#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB in system */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CFG_OR_TIMING_SDRAM 0x00000E00
-#define CFG_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK))
-#define CFG_OR1_PRELIM ( CFG_OR_AM_SDRAM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
+#define CONFIG_SYS_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK))
+#define CONFIG_SYS_OR1_PRELIM ( CONFIG_SYS_OR_AM_SDRAM | CONFIG_SYS_OR_TIMING_SDRAM )
+#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/* RPXlite mem setting */
-#define CFG_BR3_PRELIM 0xFA400001 /* BCSR */
-#define CFG_OR3_PRELIM 0xFF7F8900
-#define CFG_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
-#define CFG_OR4_PRELIM 0xFFFE0040
+#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */
+#define CONFIG_SYS_OR3_PRELIM 0xFF7F8900
+#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
+#define CONFIG_SYS_OR4_PRELIM 0xFFFE0040
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#if defined(RPXlite_64MHz)
-#define CFG_MAMR_PTA 32
+#define CONFIG_SYS_MAMR_PTA 32
#else
-#define CFG_MAMR_PTA 20
+#define CONFIG_SYS_MAMR_PTA 20
#endif
/*
* Refresh clock Prescalar
*/
-#define CFG_MPTPR MPTPR_PTP_DIV2
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2
/*
* MAMR settings for SDRAM
*/
/* 9 column SDRAM */
-#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10)
-/* CFG_MAMR_9COL:0x20904000 @ 64MHz */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+/* CONFIG_SYS_MAMR_9COL:0x20904000 @ 64MHz */
/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
/* Configuration variable added by yooth. */
#define CONFIG_ETHADDR 00:10:EC:00:37:5B
#define CONFIG_IPADDR 172.16.115.7
#define CONFIG_SERVERIP 172.16.115.6
-#define CONFIG_ROOTPATH /workspace/myfilesystem/target/
-#define CONFIG_BOOTFILE uImage.rpxusb
+#define CONFIG_ROOTPATH "/workspace/myfilesystem/target/"
+#define CONFIG_BOOTFILE "uImage.rpxusb"
+#define CONFIG_HOSTNAME LITE_H1_DW
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff