serial: Remove CONFIG_SERIAL_MULTI from config files

[karo-tx-uboot.git] / include / configs / TB5200.h

diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h
index 60102469c52d99458f351ccb42f62616cfecbade..a624c83a21c0dc6599b28566ecdd153a6b3419f8 100644 (file)
--- a/include/configs/TB5200.h
+++ b/include/configs/TB5200.h
@@ -37,10 +37,18 @@
 #define CONFIG_TQM5200         1       /* ... on TQM5200 module */
 #define CONFIG_TB5200          1       /* ... on a TB5200 base board */
 
-#define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFC000000  boot low (standard configuration with room for
+ *             max 64 MByte Flash ROM)
+ * 0xFFF00000  boot high (for a backup copy of U-Boot)
+ * 0x00100000  boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xFC000000
+#endif
 
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM          0x02    /* Software reboot           */
+#define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
 
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
 
@@ -48,7 +56,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     1       /* default console is on PSC1 */
-#define CONFIG_SERIAL_MULTI    1       /* support multiple consoles */
 #define CONFIG_PSC_CONSOLE2    6       /* second console is on PSC6 */
 #define CONFIG_BAUDRATE                115200  /* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
@@ -126,13 +133,13 @@
 #endif
 
 #ifdef CONFIG_POST
-#define CONFIG__CMD_DIAG
+#define CONFIG_CMD_DIAG
 #endif
 
 
 #define        CONFIG_TIMESTAMP                /* display image timestamps */
 
-#if (TEXT_BASE == 0xFC000000)          /* Boot low */
+#if (CONFIG_SYS_TEXT_BASE == 0xFC000000)               /* Boot low */
 #   define CONFIG_SYS_LOWBOOT          1
 #endif
 
@@ -243,15 +250,15 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  20
 
 /* List of I2C addresses to be verified by POST */
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST  {       CONFIG_SYS_I2C_EEPROM_ADDR,     \
-                               CONFIG_SYS_I2C_RTC_ADDR,        \
-                               CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS      {CONFIG_SYS_I2C_EEPROM_ADDR,    \
+                                        CONFIG_SYS_I2C_RTC_ADDR,       \
+                                        CONFIG_SYS_I2C_SLAVE}
 
 /*
  * Flash configuration
  */
-#define CONFIG_SYS_FLASH_BASE          TEXT_BASE /* 0xFC000000 */
+#define CONFIG_SYS_FLASH_BASE          CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
 
 /* use CFI flash driver */
 #define CONFIG_SYS_FLASH_CFI           1       /* Flash is CFI conformant */
@@ -275,7 +282,9 @@
                                           (= chip selects) */
 
 /* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT         "nor0=TQM5200-0"
 #if defined(CONFIG_TQM5200_B)
 #define MTDPARTS_DEFAULT       "mtdparts=TQM5200-0:768k(firmware),"    \
@@ -317,17 +326,16 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
 #ifdef CONFIG_POST
 /* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_POST_SIZE
 #else
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE
 #endif
 
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -344,10 +352,11 @@
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC     1
+#define CONFIG_MPC5xxx_FEC_MII100
 /*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
  */
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
 #define CONFIG_PHY_ADDR                0x00
 
 /*
@@ -427,13 +436,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
 
 #define CONFIG_SYS_BOOTCS_START        CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE         CONFIG_SYS_FLASH_SIZE