#define CONFIG_LOADS_ECHO 1
/* don't allow baudrate change */
-#undef CFG_LOADS_BAUD_CHANGE
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
/* supported baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* select ethernet configuration
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#undef CONFIG_ETHER_ON_SCC
#define CONFIG_ETHER_ON_FCC
#define CONFIG_ETHER_INDEX 1
/* Marvell Switch SMI base addr */
-#define CFG_PHY_ADDR 0x10
+#define CONFIG_SYS_PHY_ADDR 0x10
/* FCC1 RMII REFCLK is CLK10 */
-#define CFG_CMXFCR_VALUE CMXFCR_TF1CS_CLK10
-#define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK)
+#define CONFIG_SYS_CMXFCR_VALUE CMXFCR_TF1CS_CLK10
+#define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK)
/* BDs and buffers on 60x bus */
-#define CFG_CPMFCR_RAMTYPE 0
+#define CONFIG_SYS_CPMFCR_RAMTYPE 0
/* Local Protect, Full duplex, Flowcontrol, RMII */
-#define CFG_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\
+#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\
FCC_PSMR_FCE|FCC_PSMR_RMII)
/* bit-bang MII PHY management */
#define CONFIG_BITBANGMII
#define MDIO_PORT 1 /* Port B */
-#define CFG_MDIO_PIN 0x00002000 /* PB18 */
-#define CFG_MDC_PIN 0x00001000 /* PB19 */
-#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN)
-#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN)
-#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0)
-#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \
- else iop->pdat &= ~CFG_MDIO_PIN
-#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \
- else iop->pdat &= ~CFG_MDC_PIN
+#define CONFIG_SYS_MDIO_PIN 0x00002000 /* PB18 */
+#define CONFIG_SYS_MDC_PIN 0x00001000 /* PB19 */
+#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
+#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
+#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDC_PIN
#define MIIDELAY udelay(1)
#endif
-/* configure commands */
-#define CONFIG_COMMANDS ( CFG_CMD_AUTOSCRIPT | \
- CFG_CMD_BDI | \
- CFG_CMD_CONSOLE | \
- CFG_CMD_ECHO | \
- CFG_CMD_ENV | \
- CFG_CMD_FLASH | \
- CFG_CMD_IMI | \
- CFG_CMD_IMLS | \
- CFG_CMD_LOADB | \
- CFG_CMD_MEMORY | \
- CFG_CMD_MISC | \
- CFG_CMD_NET | \
- CFG_CMD_PING | \
- CFG_CMD_RUN )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SOURCE
+
/*
* boot options & environment
*/
/* undef to save memory */
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
/* monitor command prompt */
-#define CFG_PROMPT "=> "
+#define CONFIG_SYS_PROMPT "=> "
/* console i/o buffer size */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024
#else
-#define CFG_CBSIZE 256
+#define CONFIG_SYS_CBSIZE 256
#endif
/* print buffer size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* max number of command args */
-#define CFG_MAXARGS 16
+#define CONFIG_SYS_MAXARGS 16
/* boot argument buffer size */
-#define CFG_BARGSIZE CFG_CBSIZE
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on */
-#define CFG_MEMTEST_START 0x00100000
+#define CONFIG_SYS_MEMTEST_START 0x00100000
/* 1 ... 15 MB in DRAM */
-#define CFG_MEMTEST_END 0x00f00000
+#define CONFIG_SYS_MEMTEST_END 0x00f00000
/* full featured memtest */
-#define CFG_ALT_MEMTEST
+#define CONFIG_SYS_ALT_MEMTEST
/* default load address */
-#define CFG_LOAD_ADDR 0x00100000
+#define CONFIG_SYS_LOAD_ADDR 0x00100000
/* decrementer freq: 1 ms ticks */
-#define CFG_HZ 1000
+#define CONFIG_SYS_HZ 1000
/* configure flash */
-#define CFG_FLASH_BASE 0xff800000
-#define CFG_MAX_FLASH_BANKS 1
-#define CFG_MAX_FLASH_SECT 64
-#define CFG_FLASH_SIZE 8
-#undef CFG_FLASH_16BIT
-#define CFG_FLASH_ERASE_TOUT 240000
-#define CFG_FLASH_WRITE_TOUT 500
-#define CFG_FLASH_LOCK_TOUT 500
-#define CFG_FLASH_UNLOCK_TOUT 10000
-#define CFG_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_BASE 0xff800000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 64
+#define CONFIG_SYS_FLASH_SIZE 8
+#undef CONFIG_SYS_FLASH_16BIT
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500
+#define CONFIG_SYS_FLASH_LOCK_TOUT 500
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000
+#define CONFIG_SYS_FLASH_PROTECTION
/* monitor in flash */
-#define CFG_MONITOR_OFFSET 0x00700000
+#define CONFIG_SYS_MONITOR_OFFSET 0x00700000
/* environment in flash */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00020000)
-#define CFG_ENV_SIZE 0x00020000
-#define CFG_ENV_SECT_SIZE 0x00020000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00020000)
+#define CONFIG_ENV_SIZE 0x00020000
+#define CONFIG_ENV_SECT_SIZE 0x00020000
/*
* Initial memory map for linux
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20)
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
/* hard reset configuration words */
#ifdef CONFIG_CLKIN_66MHz
-#define CFG_HRCW_MASTER 0x04643050
+#define CONFIG_SYS_HRCW_MASTER 0x04643050
#else
#error NO HRCW FOR 100MHZ SPECIFIED !!!
#endif
-#define CFG_HRCW_SLAVE1 0x00000000
-#define CFG_HRCW_SLAVE2 0x00000000
-#define CFG_HRCW_SLAVE3 0x00000000
-#define CFG_HRCW_SLAVE4 0x00000000
-#define CFG_HRCW_SLAVE5 0x00000000
-#define CFG_HRCW_SLAVE6 0x00000000
-#define CFG_HRCW_SLAVE7 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE1 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE2 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE3 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE4 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE5 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE6 0x00000000
+#define CONFIG_SYS_HRCW_SLAVE7 0x00000000
/* internal memory mapped register */
-#define CFG_IMMR 0xF0000000
+#define CONFIG_SYS_IMMR 0xF0000000
/* definitions for initial stack pointer and data area (in DPRAM) */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2000
-#define CFG_GBL_DATA_SIZE 128
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2000
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_SIZE (32*1024*1024)
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_FLASH (CFG_FLASH_BASE + CFG_MONITOR_OFFSET)
-#define CFG_MONITOR_LEN 0x00020000
-#define CFG_MALLOC_LEN 0x00020000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_SIZE (32*1024*1024)
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_FLASH (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_OFFSET)
+#define CONFIG_SYS_MONITOR_LEN 0x00020000
+#define CONFIG_SYS_MALLOC_LEN 0x00020000
/* boot flags */
#define BOOTFLAG_COLD 0x01 /* normal power-on */
#define BOOTFLAG_WARM 0x02 /* software reboot */
/* cache configuration */
-#define CFG_CACHELINE_SIZE 32 /* for MPC8260 */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of above */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* for MPC8260 */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of above */
#endif
/*
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|\
HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
/* RMR - reset mode register - turn on checkstop reset enable */
-#define CFG_RMR RMR_CSRE
+#define CONFIG_SYS_RMR RMR_CSRE
/* BCR - bus configuration */
-#define CFG_BCR 0x00000000
+#define CONFIG_SYS_BCR 0x00000000
/* SIUMCR - siu module configuration */
-#define CFG_SIUMCR 0x4905c000
+#define CONFIG_SYS_SIUMCR 0x4905c000
/* SYPCR - system protection control */
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR 0xffffff87
+#define CONFIG_SYS_SYPCR 0xffffff87
#else
-#define CFG_SYPCR 0xffffff83
+#define CONFIG_SYS_SYPCR 0xffffff83
#endif
/* TMCNTSC - time counter status and control */
/* clear interrupts XXX jse */
-/*#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\
+/*#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\
TMCNTSC_TCF|TMCNTSC_TCE)
/* PISCR - periodic interrupt status and control */
/* clear interrupts XXX jse */
-/*#define CFG_PISCR (PISCR_PS) */
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+/*#define CONFIG_SYS_PISCR (PISCR_PS) */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/* SCCR - system clock control */
-#define CFG_SCCR 0x000001a9
+#define CONFIG_SYS_SCCR 0x000001a9
/* RCCR - risc controller configuration */
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* MEMORY MAP
* ----------
- * CS0 - FLASH 8MB/8Bit base=0xff800000 (boot: 0xfe000000, 8x mirrored)
+ * CS0 - FLASH 8MB/8Bit base=0xff800000 (boot: 0xfe000000, 8x mirrored)
* CS1 - SDRAM 32MB/64Bit base=0x00000000
* CS2 - DSP/SL1 1MB/16Bit base=0xf0100000
* CS3 - DSP/SL2 1MB/16Bit base=0xf0200000
* x - IMMR 384KB base=0xf0000000
*/
/* XXX jse 100MHz TODO */
-#define CFG_BR0_PRELIM 0xff800801
-#define CFG_OR0_PRELIM 0xff801e44
-#define CFG_BR1_PRELIM 0x00000041
-#define CFG_OR1_PRELIM 0xfe002ec0
+#define CONFIG_SYS_BR0_PRELIM 0xff800801
+#define CONFIG_SYS_OR0_PRELIM 0xff801e44
+#define CONFIG_SYS_BR1_PRELIM 0x00000041
+#define CONFIG_SYS_OR1_PRELIM 0xfe002ec0
#if 1
-#define CFG_BR2_PRELIM 0xf0101001
-#define CFG_OR2_PRELIM 0xfff00ef4
-#define CFG_BR3_PRELIM 0xf0201001
-#define CFG_OR3_PRELIM 0xfff00ef4
-#define CFG_BR4_PRELIM 0xf0301001
-#define CFG_OR4_PRELIM 0xfff00ef4
-#define CFG_BR5_PRELIM 0xf0401001
-#define CFG_OR5_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR2_PRELIM 0xf0101001
+#define CONFIG_SYS_OR2_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR3_PRELIM 0xf0201001
+#define CONFIG_SYS_OR3_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR4_PRELIM 0xf0301001
+#define CONFIG_SYS_OR4_PRELIM 0xfff00ef4
+#define CONFIG_SYS_BR5_PRELIM 0xf0401001
+#define CONFIG_SYS_OR5_PRELIM 0xfff00ef4
#else
-#define CFG_BR2_PRELIM 0xf0101081
-#define CFG_OR2_PRELIM 0xfff00104
-#define CFG_BR3_PRELIM 0xf0201081
-#define CFG_OR3_PRELIM 0xfff00104
-#define CFG_BR4_PRELIM 0xf0301081
-#define CFG_OR4_PRELIM 0xfff00104
-#define CFG_BR5_PRELIM 0xf0401081
-#define CFG_OR5_PRELIM 0xfff00104
+#define CONFIG_SYS_BR2_PRELIM 0xf0101081
+#define CONFIG_SYS_OR2_PRELIM 0xfff00104
+#define CONFIG_SYS_BR3_PRELIM 0xf0201081
+#define CONFIG_SYS_OR3_PRELIM 0xfff00104
+#define CONFIG_SYS_BR4_PRELIM 0xf0301081
+#define CONFIG_SYS_OR4_PRELIM 0xfff00104
+#define CONFIG_SYS_BR5_PRELIM 0xf0401081
+#define CONFIG_SYS_OR5_PRELIM 0xfff00104
#endif
-#define CFG_BR7_PRELIM 0xf0500881
-#define CFG_OR7_PRELIM 0xffff8104
-#define CFG_MPTPR 0x2700
-#define CFG_PSDMR 0x822a2452 /* optimal */
-/*#define CFG_PSDMR 0x822a48a3 */ /* relaxed */
-#define CFG_PSRT 0x1a
+#define CONFIG_SYS_BR7_PRELIM 0xf0500881
+#define CONFIG_SYS_OR7_PRELIM 0xffff8104
+#define CONFIG_SYS_MPTPR 0x2700
+#define CONFIG_SYS_PSDMR 0x822a2452 /* optimal */
+/*#define CONFIG_SYS_PSDMR 0x822a48a3 */ /* relaxed */
+#define CONFIG_SYS_PSRT 0x1a
/* "bad" address */
-#define CFG_RESET_ADDRESS 0x40000000
+#define CONFIG_SYS_RESET_ADDRESS 0x40000000
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff