# define CONFIG_TIMESTAMP
# define CONFIG_LZO
# ifdef CONFIG_ENABLE_VBOOT
-# define CONFIG_OF_CONTROL
-# define CONFIG_OF_SEPARATE
-# define CONFIG_DEFAULT_DEVICE_TREE am335x-boneblack
# define CONFIG_FIT_SIGNATURE
# define CONFIG_RSA
# endif
"${optargs} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \
+ "nandroot=ubi0:rootfs rw ubi.mtd=9,2048\0" \
"nandrootfstype=ubifs rootwait=1\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
"ip=dhcp\0" \
"bootenv=uEnv.txt\0" \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
+ "source ${loadaddr}\0" \
"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
- "env import -t $loadaddr $filesize\0" \
+ "env import -t -r $loadaddr $filesize\0" \
"ramargs=setenv bootargs console=${console} " \
"${optargs} " \
"root=${ramroot} " \
"mmcboot=mmc dev ${mmcdev}; " \
"if mmc rescan; then " \
"echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run loadimage; then " \
- "run mmcloados;" \
- "fi;" \
+ "if run loadbootscript; then " \
+ "run bootscript;" \
+ "else " \
+ "if run loadbootenv; then " \
+ "echo Loaded environment from ${bootenv};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loadimage; then " \
+ "run mmcloados;" \
+ "fi;" \
+ "fi ;" \
"fi;\0" \
"spiboot=echo Booting from spi ...; " \
"run spiargs; " \
/* USB gadget RNDIS */
#define CONFIG_SPL_MUSB_NEW_SUPPORT
-/* General network SPL, both CPSW and USB gadget RNDIS */
-#define CONFIG_SPL_NET_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
-
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
+#endif
#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_NAND_OMAP_ELM
+/* NAND: device related configs */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+/* NAND: driver related configs */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
#define CONFIG_SYS_NAND_ECCBYTES 14
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define MTDIDS_DEFAULT "nand0=nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=nand.0:" \
+ "128k(NAND.SPL)," \
+ "128k(NAND.SPL.backup1)," \
+ "128k(NAND.SPL.backup2)," \
+ "128k(NAND.SPL.backup3)," \
+ "256k(NAND.u-boot-spl-os)," \
+ "1m(NAND.u-boot)," \
+ "128k(NAND.u-boot-env)," \
+ "128k(NAND.u-boot-env.backup1)," \
+ "8m(NAND.kernel)," \
+ "-(NAND.rootfs)"
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x000c0000
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x001c0000
+#define CONFIG_ENV_OFFSET_REDUND 0x001e0000
+#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+/* NAND: SPL related configs */
+#ifdef CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_AM33XX_BCH
#endif
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x00080000 /* os parameters */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
+#endif /* !CONFIG_NAND */
/*
* For NOR boot, we must set this to the start of where NOR is mapped
/* disable EFI partitions and partition UUID support */
#undef CONFIG_PARTITION_UUIDS
#undef CONFIG_EFI_PARTITION
-/*
- * Disable CPSW SPL support so we fit within the 101KiB limit.
- */
-#undef CONFIG_SPL_ETH_SUPPORT
+/* General network SPL */
+#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
#endif
/* USB Device Firmware Update support */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_ENV_IS_IN_SPI_FLASH
#elif defined(CONFIG_EMMC_BOOT)
#undef CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SYS_MMC_ENV_DEV 1
#define CONFIG_SYS_MMC_ENV_PART 2
#define CONFIG_ENV_OFFSET 0x0
#define CONFIG_PHYLIB
#define CONFIG_PHY_SMSC
-/* NAND support */
-#ifdef CONFIG_NAND
-#define CONFIG_CMD_NAND
-#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
- "128k(SPL.backup1)," \
- "128k(SPL.backup2)," \
- "128k(SPL.backup3),1792k(u-boot)," \
- "128k(u-boot-spl-os)," \
- "128k(u-boot-env),5m(kernel),-(rootfs)"
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#endif
-#endif
-
/*
* NOR Size = 16 MiB
* Number of Sectors/Blocks = 128
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_FLASH_BASE (0x08000000)
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_SYS_FLASH_SIZE 0x01000000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
/* Reduce SPL size by removing unlikey targets */
#ifdef CONFIG_NOR_BOOT
projects / karo-tx-uboot.git / blobdiff