*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
#ifndef _CONFIG_ASTRO_MCF5373L_H
#define _CONFIG_ASTRO_MCF5373L_H
+#include <linux/stringify.h>
+
/*
* set the card type to actually compile for; either of
* the possibilities listed below has to be used!
#error No card type defined!
#endif
-/*
- * Define processor
- * possible values for Urmel board: only Coldfire M5373 processor supported
- * (please do not change)
- */
-
-/* it seems not clear yet which processor defines we should use */
-#define CONFIG_MCF537x /* define processor family */
-#define CONFIG_MCF532x /* define processor family */
-#define CONFIG_M5373 /* define processor type */
#define CONFIG_ASTRO5373L /* define board type */
/* Command line configuration */
-#include <config_cmd_default.h>
-
/*
* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
* a different bootloader that has already performed RAM setup) or
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_XIMG
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
#if ENABLE_JFFS
#define CONFIG_CMD_JFFS2
#endif
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_MCFRTC
#undef RTC_DEBUG
#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_FSL_I2C
-#define CONFIG_HARD_I2C /* I2C with hw support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 80000
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED 80000
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/*
* Defines processor clock - important for correct timings concerning serial
* interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
*/
-#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CLK 80000000
#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3)
#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
*/
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (2)
* u-boot: 'set' command
*/
-#define _QUOTEME(x) #x
-#define QUOTEME(x) _QUOTEME(x)
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loaderversion=11\0" \
- "card_id="QUOTEME(ASTRO_ID)"\0" \
+ "card_id="__stringify(ASTRO_ID)"\0" \
"alterafile=0\0" \
"xilinxfile=0\0" \
"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\
" loaderversion=$loaderversion"
-#define CONFIG_SYS_PROMPT "URMEL > "
-
/* default RAM address for user programs */
#define CONFIG_SYS_LOAD_ADDR 0x20000
* Definitions for initial stack pointer and data area (in internal SRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
-#define CONFIG_SYS_INIT_RAM_END 0x8000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x8000
#define CONFIG_SYS_INIT_RAM_CTRL 0x221
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \
- CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1
+#define LDS_BOARD_TEXT \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*)
+
#if ENABLE_JFFS
/* JFFS Partition offset set */
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_END - 8)
+ CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_END - 4)
+ CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
projects / karo-tx-uboot.git / blobdiff