* U-boot - Configuration file for BF533 EZKIT board
*/
-#ifndef __CONFIG_EZKIT533_H__
-#define __CONFIG_EZKIT533_H__
+#ifndef __CONFIG_BF533_EZKIT_H__
+#define __CONFIG_BF533_EZKIT_H__
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_STAMP 1
+#include <asm/config-pre.h>
-#define CONFIG_BOOTDELAY 5
-#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-#define CFG_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_LOADADDR 0x01000000 /* default load address */
-#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
-/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-#define CONFIG_DRIVER_SMC91111 1
-#define CONFIG_SMC91111_BASE 0x20310300
-#if 0
-#define CONFIG_MII
-#define CFG_DISCOVER_PHY
-#endif
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 27000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 22
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
-#define CONFIG_RTC_BFIN 1
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
/*
- * Boot Mode Set
- * Blackfin can support several boot modes
+ * Memory Settings
*/
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
-
-#define CONFIG_PANIC_HANG 1
-
-#define ADSP_BF531 0x31
-#define ADSP_BF532 0x32
-#define ADSP_BF533 0x33
-#define BFIN_CPU ADSP_BF533
-
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
-
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 27000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL */
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
-#define CONFIG_VCO_MULT 22
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
-#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#define CONFIG_MEM_SIZE 32
+/* Early EZKITs had 32megs, but later have 64megs */
+#if (CONFIG_MEM_SIZE == 64)
+# define CONFIG_MEM_ADD_WDTH 10
#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+# define CONFIG_MEM_ADD_WDTH 9
#endif
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC16M16A2TG_75 1
+#define CONFIG_EBIU_SDRRC_VAL 0x398
+#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
-#define CONFIG_LOADS_ECHO 1
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_DATE)
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
-#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
-#define CFG_LOAD_ADDR 0x01000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
-#define CFG_FLASH_BASE 0x20000000
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE 0x4000
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CFG_FLASH0_BASE 0x20000000
-#define CFG_FLASH1_BASE 0x20200000
-#define CFG_FLASH2_BASE 0x20280000
-#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20020000
-#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
-
-/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
+/*
+ * Network Settings
+ */
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20310300
+#define SMC91111_EEPROM_INIT() \
+ do { \
+ bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+ bfin_write_FIO_FLAG_C(PF1); \
+ bfin_write_FIO_FLAG_S(PF0); \
+ SSYNC(); \
+ } while (0)
+#define CONFIG_HOSTNAME bf533-ezkit
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
- * Stack sizes
+ * Flash Settings
*/
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-
-#define POLL_MODE 1
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+#define CONFIG_SYS_MAX_FLASH_SECT 40
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR 0x20030000
+#define CONFIG_ENV_SECT_SIZE 0x10000
#define FLASH_TOT_SECT 40
-#define FLASH_SIZE 0x220000
-#define CFG_FLASH_SIZE 0x220000
+
/*
- * Initialize PSD4256 registers for using I2C
+ * I2C Settings
*/
-#define CONFIG_MISC_INIT_R
+#define CONFIG_SOFT_I2C
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
+
/*
- * I2C settings
- * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ * Misc Settings
*/
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+
+
/*
- * Software (bit-bang) I2C driver configuration
+ * Pull in common ADI header for remaining command/environment setup
*/
-#define PF_SCL PF0
-#define PF_SDA PF1
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
-
-#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
-
-#define CONFIG_VDSP 1
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
+#include <configs/bfin_adi_common.h>
#endif
projects / karo-tx-uboot.git / blobdiff