at91: enable USB ethernet for taskit stamp9g20

[karo-tx-uboot.git] / include / configs / bf537-stamp.h

diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index 22d31508eb98a380b738fdf8ad47a31ff2b8ddb9..e1705cadaee4f88b3292a2a297d931c97af33b2a 100644 (file)
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -11,6 +11,7 @@
 /*
  * Processor Settings
  */
+#define CONFIG_BFIN_CPU             bf537-0.2
 #define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
 
 
@@ -51,7 +52,7 @@
 #define CONFIG_EBIU_AMBCTL0_VAL        0x7BB07BB0
 #define CONFIG_EBIU_AMBCTL1_VAL        0xFFC27BB0
 
-#define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN         (768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN          (384 * 1024)
 
 
@@ -62,7 +63,6 @@
 #define ADI_CMDS_NETWORK       1
 #define CONFIG_BFIN_MAC
 #define CONFIG_NETCONSOLE      1
-#define CONFIG_NET_MULTI       1
 #endif
 #define CONFIG_HOSTNAME                bf537-stamp
 /* Uncomment next line to use fixed MAC address */
@@ -118,13 +118,10 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-       arch/blackfin/cpu/traps.o               (.text .text.*); \
-       arch/blackfin/cpu/interrupt.o   (.text .text.*); \
-       arch/blackfin/cpu/serial.o              (.text .text.*); \
-       common/dlmalloc.o               (.text .text.*); \
-       lib/crc32.o             (.text .text.*); \
+       arch/blackfin/lib/built-in.o (.text*); \
+       arch/blackfin/cpu/built-in.o (.text*); \
        . = DEFINED(env_offset) ? env_offset : .; \
-       common/env_embedded.o           (.text .text.*);
+       common/env_embedded.o (.text*);
 #endif
 
 
@@ -138,14 +135,17 @@
 /*
  * SPI_MMC Settings
  */
+#define CONFIG_MMC_SPI
+#ifdef CONFIG_MMC_SPI
 #define CONFIG_MMC
-#define CONFIG_SPI_MMC
-
+#define CONFIG_GENERIC_MMC
+#endif
 
 /*
  * NAND Settings
  */
 /* #define CONFIG_NAND_PLAT */
+#ifdef CONFIG_NAND_PLAT
 #define CONFIG_SYS_NAND_BASE           0x20212000
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 
@@ -160,7 +160,7 @@
 #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
 #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
 #define NAND_PLAT_GPIO_DEV_READY       GPIO_PF3
-
+#endif /* CONFIG_NAND_PLAT */
 
 /*
  * CF-CARD IDE-HDD Support
@@ -254,14 +254,21 @@
 #define CONFIG_MISC_INIT_R
 #define CONFIG_RTC_BFIN
 #define CONFIG_UART_CONSOLE    0
+#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
 
 /* Define if want to do post memory test */
 #undef CONFIG_POST
 #ifdef CONFIG_POST
-#define FLASH_START_POST_BLOCK 11      /* Should > = 11 */
-#define FLASH_END_POST_BLOCK   71      /* Should < = 71 */
+#define CONFIG_SYS_POST_HOTKEYS_GPIO   GPIO_PF5
+#define CONFIG_POST_BSPEC1_GPIO_LEDS \
+       GPIO_PF6, GPIO_PF7, GPIO_PF8, GPIO_PF9, GPIO_PF10, GPIO_PF11,
+#define CONFIG_POST_BSPEC2_GPIO_BUTTONS \
+       GPIO_PF5, GPIO_PF4, GPIO_PF3, GPIO_PF2,
+#define CONFIG_POST_BSPEC2_GPIO_NAMES \
+       10, 11, 12, 13,
+#define CONFIG_SYS_POST_FLASH_START    11
+#define CONFIG_SYS_POST_FLASH_END      71
 #endif
-#define CONFIG_SYS_POST_WORD_ADDR      0xFF903FFC
 
 /* These are for board tests */
 #if 0