davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM

[karo-tx-uboot.git] / include / configs / davinci_sffsdr.h

diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
index a47620fca8d5ebcedb92a375724ca20f8305ef52..0c653915bdf83d95e76fff1a4c2c1a1441603720 100644 (file)
--- a/include/configs/davinci_sffsdr.h
+++ b/include/configs/davinci_sffsdr.h
@@ -22,7 +22,6 @@
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
-#include <asm/sizes.h>
 
 /* Board */
 #define SFFSDR
@@ -43,7 +42,6 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  20
 /* Memory Info */
 #define CONFIG_SYS_MALLOC_LEN          (0x10000 + 256*1024)    /* malloc() len */
-#define CONFIG_SYS_GBL_DATA_SIZE       128             /* reserved for initial data */
 #define CONFIG_SYS_MEMTEST_START       0x80000000      /* memtest start address */
 #define CONFIG_SYS_MEMTEST_END         0x81000000      /* 16MB RAM test */
 #define CONFIG_NR_DRAM_BANKS   1               /* we have 1 bank of DRAM */
@@ -74,16 +72,15 @@
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT 10
 #define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_NET_MULTI
 /* Flash & Environment */
 #undef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS             2
 #define CONFIG_ENV_IS_IN_NAND          /* U-Boot env in NAND Flash  */
 #define CONFIG_ENV_SECT_SIZE   2048    /* Env sector Size */
-#define CONFIG_ENV_SIZE                SZ_128K
+#define CONFIG_ENV_SIZE                (128 << 10)     /* 128 KiB */
 #define CONFIG_SKIP_LOWLEVEL_INIT      /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT     /* to a proper address, init done */
 #define CONFIG_SYS_NAND_BASE           0x02000000
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices */
@@ -144,9 +141,13 @@
 #undef CONFIG_CMD_SETGETDCR
 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS
-/* KGDB support (if any) */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE   115200  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  1       /* which serial port to use */
-#endif
+
+#define CONFIG_MAX_RAM_BANK_SIZE       (256 << 20)     /* 256 MB */
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000
+#define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_SDRAM_BASE + \
+                                        CONFIG_SYS_INIT_RAM_SIZE - \
+                                        GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */