sunxi: non-FEL SPL boot support for sun7i

[karo-tx-uboot.git] / include / configs / ep8260.h

diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
index b15659d918d62ebc4554ed401f4dad7b7443e7b2..9cd3054a15f89b55daf9709fa99e08d43c12ca25 100644 (file)
--- a/include/configs/ep8260.h
+++ b/include/configs/ep8260.h
@@ -5,23 +5,7 @@
  * This file is based on similar values for other boards found in other
  * U-Boot config files, and some that I found in the EP8260 manual.
  *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -200,8 +184,8 @@
  * - RAM for BD/Buffers is on the local Bus (see 28-13)
  * - Enable Half Duplex in FSMR
  */
-# define CONFIG_SYS_CMXFCR_MASK        (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE       (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+# define CONFIG_SYS_CMXFCR_MASK3       (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE3      (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
 
 /*
  * - RAM for BD/Buffers is on the local Bus (see 28-13)
@@ -227,15 +211,18 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#undef  CONFIG_HARD_I2C                        /* I2C with hardware support    */
-#define CONFIG_SOFT_I2C                1       /* I2C bit-banged               */
+#define CONFIG_SYS_I2C_SOFT            /* I2C bit-banged */
+
 #define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C_SLAVE           0x7F    /* This is for HARD, must go */
 
 /*
  * Software (bit-bang) I2C driver configuration
  */
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED      50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE      0xFE
 #define I2C_PORT       3               /* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE     (iop->pdir |=  0x00010000)
 #define I2C_TRISTATE   (iop->pdir &= ~0x00010000)
@@ -245,7 +232,7 @@
 #define I2C_SCL(bit)   if(bit) iop->pdat |=  0x00020000; \
                        else    iop->pdat &= ~0x00020000
 #define I2C_DELAY      udelay(5)       /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 /* #define CONFIG_RTC_DS174x */
 
@@ -279,7 +266,6 @@
 #define CONFIG_SYS_LONGHELP
 
 /* Monitor Command Prompt       */
-#define CONFIG_SYS_PROMPT              "=> "
 
 /* Define this variable to enable the "hush" shell (from
    Busybox) as command line interpreter, thus enabling
@@ -290,7 +276,6 @@
    with a somewhat smapper memory footprint.
 */
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 
 
 /*
@@ -325,7 +310,6 @@
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-#undef CONFIG_CMD_DCR
 #undef CONFIG_CMD_XIMG
 
 /* Where do the internal registers live? */
@@ -341,7 +325,6 @@
  *
  *****************************************************************************/
 
-#define CONFIG_MPC8260          1       /* This is an MPC8260 CPU   */
 #define CONFIG_EP8260           11      /* on an Embedded Planet EP8260 Board, Rev. 11 */
 
 #define CONFIG_BOARD_EARLY_INIT_F 1        /* Call board_early_init_f  */
@@ -373,12 +356,6 @@
 #define        CONFIG_CLOCKS_IN_MHZ    1      /* clocks passsed to Linux in MHz */
 
 #define CONFIG_SYS_LOAD_ADDR     0x00100000   /* default load address */
-#define CONFIG_SYS_TFTP_LOADADDR 0x00100000   /* default load address for network file downloads */
-
-#define CONFIG_SYS_HZ            1000         /* decrementer freq: 1 ms ticks */
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 
 /*
  * Low Level Configuration Settings