#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SYS_TEXT_BASE 0x40000000
+
/* Enable debug prints */
-#undef DEBUG /* General debug */
#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
/* What is the oscillator's (UX2) frequency in Hz? */
* 0x6 0x1 66 133 266 Close Close Open
* 0x6 0x2 66 133 300 Close Open Close
*/
-#define CFG_SBC_MODCK_H 0x05
+#define CONFIG_SYS_SBC_MODCK_H 0x05
/* Define this if you want to boot from 0x00000100. If you don't define
* this, you will need to program the bootloader to 0xfff00000, and
* way to do that is to program the bootloader at both addresses.
* It is suggested that you just let U-Boot live at 0x00000000.
*/
-#define CFG_SBC_BOOT_LOW 1
+#define CONFIG_SYS_SBC_BOOT_LOW 1
/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain TEXT_BASE from board/sbc8260/config.mk
+ * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE.
* The main FLASH is whichever is connected to *CS0. U-Boot expects
* this to be the SIMM.
*/
-#define CFG_FLASH0_BASE 0x40000000
-#define CFG_FLASH0_SIZE 8
+#define CONFIG_SYS_FLASH0_BASE 0x40000000
+#define CONFIG_SYS_FLASH0_SIZE 8
-/* Define CFG_FLASH_CHECKSUM to enable flash checksum during boot.
+/* Define CONFIG_SYS_FLASH_CHECKSUM to enable flash checksum during boot.
* Note: the 'flashchecksum' environment variable must also be set to 'y'.
*/
-#define CFG_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_CHECKSUM
/* What should be the base address of SDRAM DIMM and how big is
* it (in Mbytes)?
*/
-#define CFG_SDRAM0_BASE 0x00000000
-#define CFG_SDRAM0_SIZE 64
+#define CONFIG_SYS_SDRAM0_BASE 0x00000000
+#define CONFIG_SYS_SDRAM0_SIZE 64
/*
* DRAM tests
- * CFG_DRAM_TEST - enables the following tests.
+ * CONFIG_SYS_DRAM_TEST - enables the following tests.
*
- * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines
+ * CONFIG_SYS_DRAM_TEST_DATA - Enables test for shorted or open data lines
* Environment variable 'test_dram_data' must be
* set to 'y'.
- * CFG_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
+ * CONFIG_SYS_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
* addressable. Environment variable
* 'test_dram_address' must be set to 'y'.
- * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
+ * CONFIG_SYS_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
* This test takes about 6 minutes to test 64 MB.
* Environment variable 'test_dram_walk' must be
* set to 'y'.
*/
-#define CFG_DRAM_TEST
-#if defined(CFG_DRAM_TEST)
-#define CFG_DRAM_TEST_DATA
-#define CFG_DRAM_TEST_ADDRESS
-#define CFG_DRAM_TEST_WALK
-#endif /* CFG_DRAM_TEST */
+#define CONFIG_SYS_DRAM_TEST
+#if defined(CONFIG_SYS_DRAM_TEST)
+#define CONFIG_SYS_DRAM_TEST_DATA
+#define CONFIG_SYS_DRAM_TEST_ADDRESS
+#define CONFIG_SYS_DRAM_TEST_WALK
+#endif /* CONFIG_SYS_DRAM_TEST */
/*
* GW8260 with 16 MB DIMM:
* Monitor Stack Buffer (0x80)
* 0x00F5 FFB0 Board Info Data
* 0x00F6 0000 Malloc Arena
- * : CFG_ENV_SECT_SIZE, 256k
- * : CFG_MALLOC_LEN, 128k
+ * : CONFIG_ENV_SECT_SIZE, 256k
+ * : CONFIG_SYS_MALLOC_LEN, 128k
* 0x00FC 0000 RAM Copy of Monitor Code
- * : CFG_MONITOR_LEN, 256k
- * 0x00FF FFFF [End of RAM], CFG_SDRAM_SIZE - 1
+ * : CONFIG_SYS_MONITOR_LEN, 256k
+ * 0x00FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1
*/
/*
* Monitor Stack Buffer (0x80)
* 0x03F5 FFB0 Board Info Data
* 0x03F6 0000 Malloc Arena
- * : CFG_ENV_SECT_SIZE, 256k
- * : CFG_MALLOC_LEN, 128k
+ * : CONFIG_ENV_SECT_SIZE, 256k
+ * : CONFIG_SYS_MALLOC_LEN, 128k
* 0x03FC 0000 RAM Copy of Monitor Code
- * : CFG_MONITOR_LEN, 256k
- * 0x03FF FFFF [End of RAM], CFG_SDRAM_SIZE - 1
+ * : CONFIG_SYS_MONITOR_LEN, 256k
+ * 0x03FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1
*/
* Port pins used for bit-banged MII communictions (if applicable).
*/
#define MDIO_PORT 2 /* Port C */
+
+#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE MDIO_DECLARE
+
#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
* - Select bus for bd/buffers (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
* - Select bus for bd/buffers (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
* put in the same sector as U-Boot, and changing variables
* will erase U-Boot temporarily
*/
-#define CFG_ENV_IN_OWN_SECT
+#define CONFIG_ENV_IN_OWN_SECT
/* Define to allow the user to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
* To stop use: " "
*/
#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, press \" \" to stop\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Autobooting in %d seconds, press \" \" to stop\n", bootdelay
#define CONFIG_AUTOBOOT_STOP_STR " "
#undef CONFIG_AUTOBOOT_DELAY_STR
#define DEBUG_BOOTKEYS 0
#define CONFIG_BOOTP_DNS
/* undef this to save memory */
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
-#define CFG_PROMPT "=> "
+#define CONFIG_SYS_PROMPT "=> "
/*
/* Where do the internal registers live? */
-#define CFG_IMMR 0xf0000000
+#define CONFIG_SYS_IMMR 0xf0000000
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
#endif
/* What is the address of IO controller */
-#define CFG_IO_BASE 0xe0000000
+#define CONFIG_SYS_IO_BASE 0xe0000000
/*****************************************************************************
*
* Miscellaneous configurable options
*/
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16)
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CFG_MAXARGS 8 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/* Convert clocks to MHZ when passing board info to kernel.
* This must be defined for eariler 2.4 kernels (~2.4.4).
*/
#define CONFIG_CLOCKS_IN_MHZ
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* memtest works from the end of the exception vector table
* to the end of the DRAM less monitor and malloc area
*/
-#define CFG_MEMTEST_START 0x2000
+#define CONFIG_SYS_MEMTEST_START 0x2000
-#define CFG_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
+#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
-#define CFG_MEM_END_USAGE ( CFG_MONITOR_LEN \
- + CFG_MALLOC_LEN \
- + CFG_ENV_SECT_SIZE \
- + CFG_STACK_USAGE )
+#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \
+ + CONFIG_SYS_MALLOC_LEN \
+ + CONFIG_ENV_SECT_SIZE \
+ + CONFIG_SYS_STACK_USAGE )
-#define CFG_MEMTEST_END ( CFG_SDRAM_SIZE * 1024 * 1024 \
- - CFG_MEM_END_USAGE )
-
-/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \
+ - CONFIG_SYS_MEM_END_USAGE )
/*
* Low Level Configuration Settings
* You should know what you are doing if you make changes here.
*/
-#define CFG_FLASH_BASE CFG_FLASH0_BASE
-#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
-#define CFG_SDRAM_BASE CFG_SDRAM0_BASE
-#define CFG_SDRAM_SIZE CFG_SDRAM0_SIZE
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
+#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM0_SIZE
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*/
-#if defined(CFG_SBC_BOOT_LOW)
-# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
+#if defined(CONFIG_SYS_SBC_BOOT_LOW)
+# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
#else
-# define CFG_SBC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CFG_SBC_BOOT_LOW) */
+# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
+#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-/* get the HRCW ISB field from CFG_IMMR */
-#define CFG_SBC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) | \
- ((CFG_IMMR & 0x01000000) >> 7) | \
- ((CFG_IMMR & 0x00100000) >> 4) )
+/* get the HRCW ISB field from CONFIG_SYS_IMMR */
+#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \
+ ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \
+ ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-#define CFG_HRCW_MASTER ( HRCW_BPS11 | \
+#define CONFIG_SYS_HRCW_MASTER ( HRCW_BPS11 | \
HRCW_DPPC11 | \
- CFG_SBC_HRCW_IMMR | \
+ CONFIG_SYS_SBC_HRCW_IMMR | \
HRCW_MMR00 | \
HRCW_LBPC11 | \
HRCW_APPC10 | \
HRCW_CS10PC00 | \
- (CFG_SBC_MODCK_H & HRCW_MODCK_H1111) | \
- CFG_SBC_HRCW_BOOT_FLAGS )
+ (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) | \
+ CONFIG_SYS_SBC_HRCW_BOOT_FLAGS )
/* no slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CFG_RAMBOOT is platform dependent.
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
*/
-#define CFG_MONITOR_BASE CFG_FLASH0_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 * 1024 * 1024) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 32 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CFG_ENV_IN_OWN_SECT
-# define CFG_ENV_ADDR (CFG_MONITOR_BASE + (256 * 1024))
-# define CFG_ENV_SECT_SIZE (256 * 1024)
+#ifdef CONFIG_ENV_IN_OWN_SECT
+# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + (256 * 1024))
+# define CONFIG_ENV_SECT_SIZE (256 * 1024)
#else
-# define CFG_ENV_SIZE (16 * 1024)/* Size of Environment Sector */
-# define CFG_ENV_ADD ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) - CFG_ENV_SIZE)
-# define CFG_ENV_SECT_SIZE (256 * 1024)/* see README - env sect real size */
-#endif /* CFG_ENV_IN_OWN_SECT */
+# define CONFIG_ENV_SIZE (16 * 1024)/* Size of Environment Sector */
+# define CONFIG_ENV_ADD ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SIZE)
+# define CONFIG_ENV_SECT_SIZE (256 * 1024)/* see README - env sect real size */
+#endif /* CONFIG_ENV_IN_OWN_SECT */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE |\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
HID0_DCE |\
HID0_ICFI |\
HID0_DCI |\
HID0_IFEM |\
HID0_ABE)
-#define CFG_HID0_FINAL (HID0_ICE |\
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register
*-----------------------------------------------------------------------
*/
-#define CFG_RMR 0
+#define CONFIG_SYS_RMR 0
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
-#define CFG_BCR (BCR_ETM)
+#define CONFIG_SYS_BCR (BCR_ETM)
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR (SIUMCR_DPPC11 |\
+#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 |\
SIUMCR_L2CPC00 |\
SIUMCR_APPC10 |\
SIUMCR_MMR00)
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
-#define CFG_SYPCR (SYPCR_SWTC |\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_LBME |\
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC |\
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
TMCNTSC_ALR |\
TMCNTSC_TCF |\
TMCNTSC_TCE)
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS |\
+#define CONFIG_SYS_PISCR (PISCR_PS |\
PISCR_PTF |\
PISCR_PTE)
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
*/
-#define CFG_SCCR 0
+#define CONFIG_SYS_SCCR 0
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* Initialize Memory Controller:
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_GPCM_P |\
BRx_V)
* - One idle clock is inserted between a read access from the
* current bank and the next access.
*/
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_5_CLK |\
* - No data pipelining is done
* - Valid
*/
-#define CFG_BR2_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
* - Back-to-back page mode
* - Internal bank interleaving within save device enabled
*/
-#if (CFG_SDRAM0_SIZE == 16)
-#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\
+#if (CONFIG_SYS_SDRAM0_SIZE == 16)
+#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
ORxS_BPD_2 |\
ORxS_ROWST_PBI0_A9 |\
ORxS_NUMR_11)
* Ref: Section 10.3.3 on page 10-21
*-----------------------------------------------------------------------
*/
-#define CFG_PSDMR (PSDMR_RFEN |\
+#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A16_A18 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_LDOTOPRE_1C |\
PSDMR_WRC_1C |\
PSDMR_CL_2)
-#endif /* (CFG_SDRAM0_SIZE == 16) */
+#endif /* (CONFIG_SYS_SDRAM0_SIZE == 16) */
/* With a 64 MB DIMM, the OR2 is configured as follows:
*
* - Back-to-back page mode
* - Internal bank interleaving within save device enabled
*/
-#if (CFG_SDRAM0_SIZE == 64)
-#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\
+#if (CONFIG_SYS_SDRAM0_SIZE == 64)
+#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A8 |\
ORxS_NUMR_12)
* Ref: Section 10.3.3 on page 10-21
*-----------------------------------------------------------------------
*/
-#define CFG_PSDMR (PSDMR_RFEN |\
+#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A14_A16 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_LDOTOPRE_1C |\
PSDMR_WRC_1C |\
PSDMR_CL_2)
-#endif /* (CFG_SDRAM0_SIZE == 64) */
+#endif /* (CONFIG_SYS_SDRAM0_SIZE == 64) */
-#define CFG_PSRT 0x0e
-#define CFG_MPTPR MPTPR_PTP_DIV32
+#define CONFIG_SYS_PSRT 0x0e
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
/*-----------------------------------------------------------------------
* - 11 wait states
*/
-#ifdef CFG_IO_BASE
-# define CFG_BR4_PRELIM ((CFG_IO_BASE & BRx_BA_MSK) |\
+#ifdef CONFIG_SYS_IO_BASE
+# define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_L |\
BRx_V)
-# define CFG_OR4_PRELIM (ORxG_AM_MSK |\
+# define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
ORxG_SCY_11_CLK |\
ORxG_EHTR)
-#endif /* CFG_IO_BASE */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
+#endif /* CONFIG_SYS_IO_BASE */
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff