#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405GP 1
#define CONFIG_4xx 1
+#define CONFIG_HOSTNAME hcu4
+
+/*
+ * Include common defines/options for all boards produced by Netstal Maschinen
+ */
+#include "netstal-common.h"
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE
#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*-----------------------------------------------------------------------
* Serial Port
* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_SERIAL_MULTI 1
-/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */
#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD 691200
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-
/* Set console baudrate to 9600 */
#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Flash
*----------------------------------------------------------------------*/
*----------------------------------------------------------------------*/
#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/* This is the 7bit address of the device, not including P. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#undef CONFIG_SYS_I2C_MULTI_EEPROMS
-
+#define CONFIG_IPADDR 172.25.1.14
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#define CONFIG_HOSTNAME hcu4
-#define CONFIG_IPADDR 172.25.1.99
-#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_SERVERIP 172.25.1.3
-
-#define CONFIG_SYS_TFTP_LOADADDR 0x01000000 /* @16 MB */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "loadaddr=0x01000000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/home/diagnose/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/hcu4/uImage\0" \
- "load=tftp 100000 hcu4/u-boot.bin\0" \
- "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \
- "cp.b 100000 FFFB0000 50000\0" \
- "upd=run load update\0" \
- "vx_rom=hcu4/hcu4_vx_rom\0" \
- "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \
- "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \
- " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_NETSTAL_DEF_ENV \
+ CONFIG_NETSTAL_DEF_ENV_POWERPC \
""
-#define CONFIG_BOOTCOMMAND "run vx"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 1 /* PHY address */
-
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & desC */
/*
* BOOTP options
CONFIG_SYS_POST_ETHER | \
CONFIG_SYS_POST_SPR)
-#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE}
-#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
#undef CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff