Merge branch 'master' of git://git.denx.de/u-boot-arm

[karo-tx-uboot.git] / include / configs / innokom.h

diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 1b05b8058a51e9f3031961c0a669f6c4daad1944..9cb0d42eac7b02dfd71ab8a6aec195077710f033 100644 (file)
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -39,6 +39,10 @@
 
 #undef CONFIG_USE_IRQ                  /* we don't need IRQ/FIQ stuff      */
                                        /* for timer/console/ethernet       */
+
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_NO_DCACHE
+
 /*
  * Hardware drivers
  */
@@ -46,6 +50,7 @@
 /*
  * select serial console configuration
  */
+#define CONFIG_PXA_SERIAL
 #define CONFIG_FFUART          1       /* we use FFUART on CSB226 */
 
 /* allow to overwrite serial and ethaddr */
@@ -73,7 +78,7 @@
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ECHO
-#define CONFIG_CMD_ENV
+#define CONFIG_CMD_SAVEENV
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMI
@@ -115,11 +120,9 @@
 #define CONFIG_SYS_MEMTEST_START       0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa3000000      /* load kernel to this address   */
 
-#define CONFIG_SYS_HZ                  3686400         /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_HZ                  1000
                                                /* RS: the oscillator is actually 3680130?? */
 
 #define CONFIG_SYS_CPUSPEED            0x141           /* set core clock to 200/200/100 MHz */
@@ -154,7 +157,8 @@
 /*
  * SMSC91C111 Network Card
  */
-#define CONFIG_DRIVER_SMC91111         1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111                1
 #define CONFIG_SMC91111_BASE           0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT                     /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY                  /* we use internal phy   */
@@ -203,7 +207,7 @@
 */
 
 /* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV               "nor0"
 #define CONFIG_JFFS2_PART_SIZE         0xFFFFFFFF
 #define CONFIG_JFFS2_PART_OFFSET       0x00000000
@@ -211,7 +215,7 @@
 /* mtdparts command line support */
 /* Note: fake mtd_id used, no linux mtd map file */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT         "nor0=innokom-0"
 */