#define CONFIG_PHYS_64BIT
#define CONFIG_PPC_P2041
-#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#define CONFIG_SYS_TEXT_BASE 0xfff40000
#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
+/* an additionnal option is required for UBI as subpage access is
+ * supported in u-boot */
+#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
+
#define CONFIG_NAND_ECC_BCH
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
/* common KM defines */
#include "keymile-common.h"
#define CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg
-#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg
+#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
#define CONFIG_MP /* support multiple processors */
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
/*
* Config the L3 Cache as L3 SRAM
#define CONFIG_KM_PNVRAM 0x80000
/* physical RAM MTD size [hex] */
#define CONFIG_KM_PHRAM 0x100000
-/* resereved pram area at the end of memroy [hex] */
-#define CONFIG_KM_RESERVED_PRAM 0x0
-/* enable protected RAM */
-#define CONFIG_PRAM 0
+/* reserved pram area at the end of memory [hex]
+ * u-boot reserves some memory for the MP boot page */
+#define CONFIG_KM_RESERVED_PRAM 0x1000
+/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
+ * is not valid yet, which is the case for when u-boot copies itself to RAM */
+#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
#define CONFIG_KM_CRAMFS_ADDR 0x2000000
#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
-#define CONFIG_BOOTCOUNT_LIMIT
-
/*
* Local Bus Definitions
*/
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
+/* bootcounter in QRIO */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20)
+
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_LAST_STAGE_INIT
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
/* Serial Port - controlled on board with jumper J8
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
+
#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
#define CONFIG_SYS_NUM_I2C_BUSES 3
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
}
+#ifndef __ASSEMBLY__
+void set_sda(int state);
+void set_scl(int state);
+int get_sda(void);
+int get_scl(void);
+#endif
#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
* eSPI - Enhanced SPI
*/
#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE 0
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
+ CONFIG_SYS_BMAN_CENA_SIZE)
+#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
+ CONFIG_SYS_QMAN_CENA_SIZE)
+#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
* ucode is stored after env, so we got 0x120000.
*/
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x120000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+/*
+ * Hardware Watchdog
+ */
+#define CONFIG_WATCHDOG /* enable CPU watchdog */
+#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
+#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
+
+
/*
* additionnal command line configuration.
*/
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
+#define CONFIG_CMD_ERRATA
/* we don't need flash support */
#define CONFIG_SYS_NO_FLASH
"update=" \
"sf probe 0;sf erase 0 +${filesize};" \
"sf write ${load_addr_r} 0 ${filesize};\0" \
+ "set_fdthigh=true\0" \
""
#define CONFIG_HW_ENV_SETTINGS \
projects / karo-tx-uboot.git / blobdiff