* If we are developing, we might want to start u-boot from ram
* so we MUST NOT initialize critical regs like mem-timing ...
*/
-#undef CONFIG_INIT_CRITICAL /* undef for developing */
-
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* High Level Configuration Options
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* Hardware drivers
/*
* select serial console configuration
*/
+#define CONFIG_LPC2292_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_FAT | \
- CFG_CMD_MMC | \
- CFG_CMD_NET | \
- CFG_CMD_PING)
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
#define CONFIG_BOOTDELAY 5
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "LPC2292SODIMM # " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x40000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x40000000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "LPC2292SODIMM # " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x40000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x40000000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0x00040000 /* default load address for */
+#define CONFIG_SYS_LOAD_ADDR 0x00040000 /* default load address for */
/* armadillo: kernel img is here*/
-#define CFG_SYS_CLK_FREQ 58982400 /* Hz */
-#define CFG_HZ 2048 /* decrementer freq in Hz */
+#define CONFIG_SYS_SYS_CLK_FREQ 58982400 /* Hz */
+#define CONFIG_SYS_HZ 2048 /* decrementer freq in Hz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
#define PHYS_FLASH_1 0x80000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00200000 /* 2 MB */
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 1024 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (0x0 + 0x3C000) /* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (0x0 + 0x3C000) /* Addr of Environment Sector */
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_MMC 1
/* we use this ethernet chip */
-#define CONFIG_ENC28J60
+#define CONFIG_ENC28J60_LPC2292
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff