/*
- * (C) Copyright 2007
+ * (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* This program is free software; you can redistribute it and/or
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_RESET 1 /* Call board_reset */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
/*
* On LWMON5 we use D-cache as init-ram and stack pointer. We also move
* the POST_WORD from OCM to a 440EPx register that preserves it's
- * content during reset (GPT0_COM6). This way we reserve the OCM (16k)
- * for logbuffer only.
+ * content during reset (GPT0_COMP6). This way we reserve the OCM (16k)
+ * for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.)
*/
#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
/* unused GPT0 COMP reg */
+#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+ /* 440EPx errata CHIP 11 */
+#define CFG_OCM_SIZE (16 << 10)
+
+/* Additional registers for watchdog timer post test */
+
+#define CFG_WATCHDOG_TIME_ADDR (CFG_PERIPHERAL_BASE + GPT0_MASK2)
+#define CFG_WATCHDOG_FLAGS_ADDR (CFG_PERIPHERAL_BASE + GPT0_MASK1)
+#define CFG_DSPIC_TEST_ADDR CFG_WATCHDOG_FLAGS_ADDR
+#define CFG_OCM_STATUS_ADDR CFG_WATCHDOG_FLAGS_ADDR
+#define CFG_WATCHDOG_MAGIC 0x12480000
+#define CFG_WATCHDOG_MAGIC_MASK 0xFFFF0000
+#define CFG_DSPIC_TEST_MASK 0x00000001
+#define CFG_OCM_STATUS_OK 0x00009A00
+#define CFG_OCM_STATUS_FAIL 0x0000A300
+#define CFG_OCM_STATUS_MASK 0x0000FF00
/*-----------------------------------------------------------------------
* Serial Port
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH0 0xFC000000
#define CFG_FLASH1 0xF8000000
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*-----------------------------------------------------------------------
* DDR SDRAM
#define CFG_MBYTES_SDRAM (256) /* 256MB */
#define CFG_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */
-#if 0 /* test-only: disable ECC for now */
#define CONFIG_DDR_ECC 1 /* enable ECC */
#define CFG_POST_ECC_ON CFG_POST_ECC
-#else
-#define CFG_POST_ECC_ON 0
-#endif
/* POST support */
#define CONFIG_POST (CFG_POST_CACHE | \
CFG_POST_FPU | \
CFG_POST_I2C | \
CFG_POST_MEMORY | \
+ CFG_POST_OCM | \
CFG_POST_RTC | \
CFG_POST_SPR | \
- CFG_POST_UART)
+ CFG_POST_UART | \
+ CFG_POST_SYSMON | \
+ CFG_POST_WATCHDOG | \
+ CFG_POST_DSP | \
+ CFG_POST_BSPEC1 | \
+ CFG_POST_BSPEC2 | \
+ CFG_POST_BSPEC3 | \
+ CFG_POST_BSPEC4 | \
+ CFG_POST_BSPEC5)
+
+#define CONFIG_POST_WATCHDOG {\
+ "Watchdog timer test", \
+ "watchdog", \
+ "This test checks the watchdog timer.", \
+ POST_RAM | POST_POWERON | POST_SLOWTEST | POST_MANUAL | POST_REBOOT, \
+ &lwmon5_watchdog_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_WATCHDOG \
+ }
+
+#define CONFIG_POST_BSPEC1 {\
+ "dsPIC init test", \
+ "dspic_init", \
+ "This test returns result of dsPIC READY test run earlier.", \
+ POST_RAM | POST_ALWAYS, \
+ &dspic_init_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_BSPEC1 \
+ }
+
+#define CONFIG_POST_BSPEC2 {\
+ "dsPIC test", \
+ "dspic", \
+ "This test gets result of dsPIC POST and dsPIC version.", \
+ POST_RAM | POST_ALWAYS, \
+ &dspic_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_BSPEC2 \
+ }
+
+#define CONFIG_POST_BSPEC3 {\
+ "FPGA test", \
+ "fpga", \
+ "This test checks FPGA registers and memory.", \
+ POST_RAM | POST_ALWAYS, \
+ &fpga_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_BSPEC3 \
+ }
+
+#define CONFIG_POST_BSPEC4 {\
+ "GDC test", \
+ "gdc", \
+ "This test checks GDC registers and memory.", \
+ POST_RAM | POST_ALWAYS, \
+ &gdc_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_BSPEC4 \
+ }
+
+#define CONFIG_POST_BSPEC5 {\
+ "SYSMON1 test", \
+ "sysmon1", \
+ "This test checks GPIO_62_EPX pin indicating power failure.", \
+ POST_RAM | POST_MANUAL | POST_NORMAL | POST_SLOWTEST, \
+ &sysmon1_post_test, \
+ NULL, \
+ NULL, \
+ CFG_POST_BSPEC5 \
+ }
#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
#define CONFIG_LOGBUFFER
+/* Reserve GPT0_COMP1-COMP5 for logbuffer header */
+#define CONFIG_ALT_LH_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP1)
+#define CONFIG_ALT_LB_ADDR (CFG_OCM_BASE)
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
/*-----------------------------------------------------------------------
#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */
#define CFG_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
+#define CFG_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */
#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */
#if 0
#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nEnter password - autoboot in %d sec...\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */
#endif
"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
"update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \
"cp.b 200000 FFF80000 80000\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
"lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \
"autoscr 200000\0" \
""
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
+/* Video console */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MB862xx
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define VIDEO_FB_16BPP_PIXEL_SWAP
+
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+
/* USB */
#ifdef CONFIG_440EPX
#define CONFIG_USB_OHCI
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
+
#ifdef CONFIG_440EPX
#define CONFIG_CMD_USB
#endif
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-#if 0
-/*
- * ToDo: Watchdog is not test fully, so exclude it for now
- */
#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */
-#endif
+#define CONFIG_WD_PERIOD 40000 /* in usec */
+#define CONFIG_WD_MAX_RATE 66600 /* in ticks */
/*
* For booting Linux, the board info and command line data
#define CFG_GPIO_PHY1_RST 12
#define CFG_GPIO_FLASH_WP 14
#define CFG_GPIO_PHY0_RST 22
+#define CFG_GPIO_DSPIC_READY 51
#define CFG_GPIO_EEPROM_EXT_WP 55
+#define CFG_GPIO_HIGHSIDE 56
#define CFG_GPIO_EEPROM_INT_WP 57
+#define CFG_GPIO_BOARD_RESET 58
#define CFG_GPIO_LIME_S 59
#define CFG_GPIO_LIME_RST 60
+#define CFG_GPIO_SYSMON_STATUS 62
#define CFG_GPIO_WATCHDOG 63
/*-----------------------------------------------------------------------
projects / karo-tx-uboot.git / blobdiff