Merge branch 'master' of git://www.denx.de/git/u-boot-imx

[karo-tx-uboot.git] / include / configs / lwmon5.h

diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index e2c436ff97918b34fe7aa118a683f0c28b0ae12a..e9c8d8fd554a468c1f9f4925dbed1db09a6f156a 100644 (file)
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -285,11 +285,11 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C                                /* I2C with hardware support    */
-#undef CONFIG_SOFT_I2C                         /* I2C bit-banged               */
-#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
-#define CONFIG_SYS_I2C_SPEED           100000          /* I2C speed and slave address  */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0          100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0          0x7F
 
 #define CONFIG_SYS_I2C_RTC_ADDR        0x51    /* RTC                          */
 #define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52    /* EEPROM          (CPU Modul)  */
@@ -463,7 +463,6 @@
 #define CONFIG_SUPPORT_VFAT
 
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory         */
-#define CONFIG_SYS_PROMPT              "=> "   /* Monitor Command Prompt       */
 
 #define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
 
@@ -482,8 +481,6 @@
 #define CONFIG_SYS_LOAD_ADDR           0x100000  /* default load address       */
 #define CONFIG_SYS_EXTBDINFO           1       /* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
-
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
@@ -565,6 +562,7 @@
 #define CONFIG_SYS_GPIO_PHY1_RST       12
 #define CONFIG_SYS_GPIO_FLASH_WP       14
 #define CONFIG_SYS_GPIO_PHY0_RST       22
+#define CONFIG_SYS_GPIO_PERM_VOLT_FEED 49
 #define CONFIG_SYS_GPIO_DSPIC_READY    51
 #define CONFIG_SYS_GPIO_CAN_ENABLE     53
 #define CONFIG_SYS_GPIO_LSB_ENABLE     54
@@ -577,6 +575,13 @@
 #define CONFIG_SYS_GPIO_SYSMON_STATUS  62
 #define CONFIG_SYS_GPIO_WATCHDOG       63
 
+/* On LCD4, GPIO49 has to be configured to 0 instead of 1 */
+#ifdef CONFIG_LCD4_LWMON5
+#define GPIO49_VAL     0
+#else
+#define GPIO49_VAL     1
+#endif
+
 /*
  * PPC440 GPIO Configuration
  */
@@ -635,7 +640,7 @@
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7)    DMA_REQ(0)      */      \
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8)    DMA_ACK(0)      */      \
 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9)    DMA_EOT/TC(0)   */      \
-{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO49  Unselect via TraceSelect Bit */      \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO49_VAL}, /* GPIO49  Unselect via TraceSelect Bit */      \
 {GPIO1_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO50  Unselect via TraceSelect Bit */      \
 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51  Unselect via TraceSelect Bit */      \
 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52  Unselect via TraceSelect Bit */      \
@@ -655,7 +660,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2           /* which serial port to use */
 #endif
 
 /*