*
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __M28EVK_CONFIG_H__
-#define __M28EVK_CONFIG_H__
+#ifndef __CONFIGS_M28EVK_H__
+#define __CONFIGS_M28EVK_H__
-/*
- * SoC configurations
- */
-#define CONFIG_MX28 /* i.MX28 SoC */
-#define CONFIG_MXS_GPIO /* GPIO control */
-#define CONFIG_SYS_HZ 1000 /* Ticks per second */
-/*
- * Define M28EVK machine type by hand until it lands in mach-types
- */
+/* System configurations */
+#define CONFIG_MX28 /* i.MX28 SoC */
#define MACH_TYPE_M28EVK 3613
-
#define CONFIG_MACH_TYPE MACH_TYPE_M28EVK
-#include <asm/arch/regs-base.h>
-
+/* U-Boot Commands */
#define CONFIG_SYS_NO_FLASH
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_ARCH_MISC_INIT
-
-/*
- * SPL
- */
-#define CONFIG_SPL
-#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
-#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
-
-/*
- * U-Boot Commands
- */
#include <config_cmd_default.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION
#define CONFIG_REGEX /* Enable regular expression support */
-/*
- * Memory configurations
- */
+/* Memory configuration */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define PHYS_SDRAM_1 0x40000000 /* Base address */
#define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
-#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */
-#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */
-#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-/* Point initial SP in SRAM so SPL can use it too. */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000
-#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024)
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-/*
- * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
- * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
- * binary. In case there was more of this mess, 0x100 bytes are skipped.
- */
-#define CONFIG_SYS_TEXT_BASE 0x40000100
-
-/*
- * U-Boot general configurations
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "=> "
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
- /* Print buffer size */
-#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
- /* Boot argument buffer size */
-#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
-#define CONFIG_AUTO_COMPLETE /* Command auto complete */
-#define CONFIG_CMDLINE_EDITING /* Command history etc */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Serial Driver
- */
-#define CONFIG_PL011_SERIAL
-#define CONFIG_PL011_CLOCK 24000000
-#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
-#define CONFIG_CONS_INDEX 0
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-
-/*
- * MMC Driver
- */
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MXS_MMC
-#endif
-/*
- * APBH DMA
- */
-#define CONFIG_APBH_DMA
-
-/*
- * NAND
- */
+/* Environment */
#define CONFIG_ENV_SIZE (16 * 1024)
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_MXS
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x60000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_ENV_IS_IN_NAND
/* Environment is in NAND */
-#define CONFIG_ENV_IS_IN_NAND
+#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_RANGE (512 * 1024)
#define CONFIG_ENV_IS_NOWHERE
#endif
-/*
- * Ethernet on SOC (FEC)
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_ETHPRIME "FEC0"
+/* FEC Ethernet on SoC */
+#ifdef CONFIG_CMD_NET
#define CONFIG_FEC_MXC
-#define CONFIG_MII
-#define CONFIG_FEC_XCV_TYPE RMII
#endif
-/*
- * I2C
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MXS
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 400000
-#endif
-
-/*
- * EEPROM
- */
-#ifdef CONFIG_CMD_EEPROM
+/* EEPROM */
+#ifdef CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#endif
-/*
- * RTC
- */
-#ifdef CONFIG_CMD_DATE
+/* RTC */
+#ifdef CONFIG_CMD_DATE
/* Use the internal RTC in the MXS chip */
#define CONFIG_RTC_INTERNAL
-#ifdef CONFIG_RTC_INTERNAL
+#ifdef CONFIG_RTC_INTERNAL
#define CONFIG_RTC_MXS
#else
#define CONFIG_RTC_M41T62
#endif
#endif
-/*
- * USB
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MXS
+/* USB */
+#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_MXS_PORT0
#define CONFIG_EHCI_MXS_PORT1
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#endif
-/*
- * SPI
- */
-#ifdef CONFIG_CMD_SPI
-#define CONFIG_HARD_SPI
-#define CONFIG_MXS_SPI
-#define CONFIG_SPI_HALF_DUPLEX
+/* SPI */
+#ifdef CONFIG_CMD_SPI
#define CONFIG_DEFAULT_SPI_BUS 2
#define CONFIG_DEFAULT_SPI_CS 0
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
/* SPI FLASH */
-#ifdef CONFIG_CMD_SF
+#ifdef CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SF_DEFAULT_BUS 2
#define CONFIG_ENV_SPI_MAX_HZ 40000000
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
#endif
+
#endif
-/*
- * LCD
- */
-#ifdef CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_MXS
+/* LCD */
+#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SPLASH_SCREEN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
#endif
-/*
- * Boot Linux
- */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
+/* Booting Linux */
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 "
#define CONFIG_BOOTCOMMAND "run bootcmd_net"
#define CONFIG_LOADADDR 0x42000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_OF_LIBFDT
-/*
- * Extra Environments
- */
+/* Extra Environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
"update_nand_full_filename=u-boot.nand\0" \
"update_nand_firmware_filename=u-boot.sb\0" \
"fi ; " \
"fi\0"
-#endif /* __M28EVK_CONFIG_H__ */
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_M28EVK_H__ */
projects / karo-tx-uboot.git / blobdiff