/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
* (C) Copyright 2007-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */
+#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME makalu
+#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFC000000
-#define CFG_FPGA_BASE 0xF0000000
-#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
+#define CONFIG_SYS_FLASH_BASE 0xFC000000
+#define CONFIG_SYS_FPGA_BASE 0xF0000000
/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16)
-
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ * There are traditionally three options for the primordial
+ * (i.e. initial) stack usage on the 405-series:
+ *
+ * 1) On-chip Memory (OCM) (i.e. SRAM)
+ * 2) Data cache
+ * 3) SDRAM
+ *
+ * For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ * the latter of which is less than desireable since it requires
+ * setting up the SDRAM and ECC in assembly code.
+ *
+ * To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
+ * select on the External Bus Controller (EBC) and then select a
+ * value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
+ * physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
+ * select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
+ * physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CONFIG_SYS_INIT_DCACHE_CS 4
+
+#if defined(CONFIG_SYS_INIT_DCACHE_CS)
+#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
+#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
+
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CONFIG_SYS_INIT_DCACHE_CS)
+# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CONFIG_SYS_INIT_EXTRA_SIZE 16
+# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
+# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR
+#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no ext. clk */
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM 256
+#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
+
+#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE)
+#define CONFIG_SYS_SDRAM0_MB1CF_BASE ((128 << 20) + CONFIG_SYS_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_128MB | \
+ SDRAM_RXBAS_SDAM_MODE2 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CONFIG_SYS_SDRAM0_MB1CF ((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_128MB | \
+ SDRAM_RXBAS_SDAM_MODE2 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
+#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
+#define CONFIG_SYS_SDRAM0_MCOPT1 0x04322000
+#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
+#define CONFIG_SYS_SDRAM0_MODT0 0x01800000
+#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
+#define CONFIG_SYS_SDRAM0_CODT 0x0080f837
+#define CONFIG_SYS_SDRAM0_RTR 0x06180000
+#define CONFIG_SYS_SDRAM0_INITPLR0 0xa8380000
+#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400
+#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000
+#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000
+#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010404
+#define CONFIG_SYS_SDRAM0_INITPLR5 0x81000542
+#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400
+#define CONFIG_SYS_SDRAM0_INITPLR7 0x8D080000
+#define CONFIG_SYS_SDRAM0_INITPLR8 0x8D080000
+#define CONFIG_SYS_SDRAM0_INITPLR9 0x8D080000
+#define CONFIG_SYS_SDRAM0_INITPLR10 0x8D080000
+#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442
+#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010780
+#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010400
+#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000
+#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000
+#define CONFIG_SYS_SDRAM0_RQDC 0x80000038
+#define CONFIG_SYS_SDRAM0_RFDC 0x00000209
+#define CONFIG_SYS_SDRAM0_RDCC 0x40000000
+#define CONFIG_SYS_SDRAM0_DLCR 0x030000a5
+#define CONFIG_SYS_SDRAM0_CLKTR 0x80000000
+#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000
+#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000
+#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232
+#define CONFIG_SYS_SDRAM0_SDTR3 0x080b0d1a
+#define CONFIG_SYS_SDRAM0_MMODE 0x00000442
+#define CONFIG_SYS_SDRAM0_MEMODE 0x00000404
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
-#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* Standard DTT sensor configuration */
#define CONFIG_DTT_DS1775 1
#define CONFIG_DTT_SENSORS { 0 }
-#define CFG_I2C_DTT_ADDR 0x48
+#define CONFIG_SYS_I2C_DTT_ADDR 0x48
/* RTC configuration */
#define CONFIG_RTC_X1205 1
-#define CFG_I2C_RTC_ADDR 0x6f
+#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII
#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=makalu\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \
- "flash_self_old=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=makalu/uImage\0" \
- "fdt_file=makalu/makalu.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 makalu/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CACHE | \
- CFG_POST_CPU | \
- CFG_POST_ETHER | \
- CFG_POST_I2C | \
- CFG_POST_MEMORY | \
- CFG_POST_UART)
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_UART)
/* Define here the base-addresses of the UARTs to test in POST */
-#define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE}
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \
+ CONFIG_SYS_NS16550_COM2 }
#define CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
/*-----------------------------------------------------------------------
* PCI stuff
/*-----------------------------------------------------------------------
* PCIe stuff
*----------------------------------------------------------------------*/
-#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
-#define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */
+#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
+#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */
-#define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */
-#define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */
-#define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */
+#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */
+#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */
+#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */
-#define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */
-#define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */
-#define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */
+#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */
+#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */
+#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */
-#define CFG_PCIE0_UTLBASE 0xef502000
-#define CFG_PCIE1_UTLBASE 0xef503000
+#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000
+#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000
/* base address of inbound PCIe window */
-#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x08033700
-#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB0AP 0x08033700
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x9400C800
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB2AP 0x9400C800
+#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */
-#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */
+#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
} \
}
-#define CFG_GPIO_PCIE_RST 23
-#define CFG_GPIO_PCIE_CLKREQ 27
-#define CFG_GPIO_PCIE_WAKE 28
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_SYS_GPIO_PCIE_RST 23
+#define CONFIG_SYS_GPIO_PCIE_CLKREQ 27
+#define CONFIG_SYS_GPIO_PCIE_WAKE 28
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff