Drop support for CONFIG_SKIP_RELOCATE_UBOOT

[karo-tx-uboot.git] / include / configs / meesc.h

diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index ab5cbca1860004dc0da1e452b0420e800f6112fd..a27b36b3786a3549d39e0aed0db6b55639bf0c92 100644 (file)
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop@leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009
+ * (C) Copyright 2009-2010
  * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -32,10 +32,11 @@
 #define __CONFIG_H
 
 /* Common stuff */
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq */
 #define CONFIG_MEESC                   1       /* Board is esd MEESC */
 #define CONFIG_ARM926EJS               1       /* This is an ARM926EJS Core */
 #define CONFIG_AT91SAM9263             1       /* It's an AT91SAM9263 SoC */
+#define CONFIG_SYS_AT91_MAIN_CLOCK     16000000/* 16.0 MHz crystal */
+#define CONFIG_SYS_HZ                  1000    /* decrementer freq */
 #define CONFIG_DISPLAY_BOARDINFO       1
 #define CONFIG_DISPLAY_CPUINFO         1       /* display cpu info and speed */
 #define CONFIG_PREBOOT                         /* enable preboot variable */
@@ -47,7 +48,7 @@
 #undef CONFIG_USE_IRQ                          /* don't need IRQ/FIQ stuff */
 
 #define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
+#define CONFIG_MISC_INIT_R                     /* Call misc_init_r */
 
 #define CONFIG_ARCH_CPU_INIT
 
@@ -56,6 +57,7 @@
  */
 
 /* Console output */
+#define CONFIG_AT91_GPIO                       1
 #define CONFIG_ATMEL_USART                     1
 #undef CONFIG_USART0
 #undef CONFIG_USART1
@@ -78,15 +80,14 @@
  */
 #include <config_cmd_default.h>
 #undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_AUTOSCRIPT
 #undef CONFIG_CMD_FPGA
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_USB
 
 #define CONFIG_CMD_PING                                1
 #define CONFIG_CMD_DHCP                                1
 #define CONFIG_CMD_NAND                                1
+#define CONFIG_CMD_USB                         1
 
 /* LED */
 #define CONFIG_AT91_LED                                1
@@ -118,9 +119,9 @@
 #define CONFIG_SYS_NAND_MASK_ALE               (1 << 21)
 /* our CLE is AD22 */
 #define CONFIG_SYS_NAND_MASK_CLE               (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN             AT91_PIN_PD15
-#define CONFIG_SYS_NAND_READY_PIN              AT91_PIN_PA22
-
+#define CONFIG_SYS_NAND_ENABLE_PIN             AT91_PIO_PORTD, 15
+#define CONFIG_SYS_NAND_READY_PIN              AT91_PIO_PORTA, 22
+#define CONFIG_SYS_64BIT_VSPRINTF              /* needed for nand_util.c */
 #endif
 
 /* Ethernet */
@@ -130,6 +131,17 @@
 #define CONFIG_NET_RETRY_COUNT                 20
 #undef CONFIG_RESET_PHY_R
 
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW                    1
+#define CONFIG_DOS_PARTITION                   1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT           1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE          0x00a00000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME          "at91sam9263"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     2
+#define CONFIG_USB_STORAGE                     1
+#define CONFIG_CMD_FAT                         1
+
 #define CONFIG_SYS_LOAD_ADDR                   0x22000000 /* load address */
 
 #define CONFIG_SYS_MEMTEST_START               PHYS_SDRAM
@@ -169,7 +181,6 @@
  */
 #define CONFIG_SYS_MALLOC_LEN          ROUND(3 * CONFIG_ENV_SIZE + \
                                        128*1024, 0x1000)
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* 128 bytes for initial data */
 
 #define CONFIG_STACKSIZE               (32 * 1024)     /* regular stack */