avr32: allow multi block mmc access for all boards

[karo-tx-uboot.git] / include / configs / mimc200.h

diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h
index 6ed9e75bb467f4d5d981ca963f5836713225622b..8031a05fc818e9c4e8da8e75c4bcd7b9692cff65 100644 (file)
--- a/include/configs/mimc200.h
+++ b/include/configs/mimc200.h
@@ -24,14 +24,14 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#include <asm/arch/memory-map.h>
+#include <asm/arch/hardware.h>
 
-#define CONFIG_AVR32                   1
-#define CONFIG_AT32AP                  1
-#define CONFIG_AT32AP7000              1
-#define CONFIG_MIMC200                 1
+#define CONFIG_AVR32
+#define CONFIG_AT32AP
+#define CONFIG_AT32AP7000
+#define CONFIG_MIMC200
 
-#define CONFIG_MIMC200_EXT_FLASH       1
+#define CONFIG_MIMC200_EXT_FLASH
 
 #define CONFIG_SYS_HZ                          1000
 
@@ -40,8 +40,8 @@
  * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
  * and the PBA bus to run at 1/4 the PLL frequency.
  */
-#define CONFIG_PLL                     1
-#define CONFIG_SYS_POWER_MANAGER               1
+#define CONFIG_PLL
+#define CONFIG_SYS_POWER_MANAGER
 #define CONFIG_SYS_OSC0_HZ                     10000000
 #define CONFIG_SYS_PLL0_DIV                    1
 #define CONFIG_SYS_PLL0_MUL                    15
@@ -63,15 +63,17 @@
  */
 #define CONFIG_SYS_PLL0_OPT                    0x04
 
-#define CONFIG_USART1                  1
+#define CONFIG_USART_BASE                      ATMEL_BASE_USART1
+#define CONFIG_USART_ID                                1
+
 #define CONFIG_MIMC200_DBGLINK         1
 
 /* User serviceable stuff */
-#define CONFIG_DOS_PARTITION           1
+#define CONFIG_DOS_PARTITION
 
-#define CONFIG_CMDLINE_TAG             1
-#define CONFIG_SETUP_MEMORY_TAGS       1
-#define CONFIG_INITRD_TAG              1
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
 
 #define CONFIG_STACKSIZE               (2048)
 
@@ -81,9 +83,9 @@
 #define CONFIG_BOOTCOMMAND                                             \
        "fsload boot/uImage; bootm"
 
-#define CONFIG_SILENT_CONSOLE          1       /* enable silent startup */
-#define CONFIG_DISABLE_CONSOLE         1       /* disable console */
-#define CONFIG_SYS_DEVICE_NULLDEV              1       /* include nulldev device */
+#define CONFIG_SILENT_CONSOLE       /* enable silent startup */
+#define CONFIG_DISABLE_CONSOLE      /* disable console */
+#define CONFIG_SYS_DEVICE_NULLDEV   /* include nulldev device */
 
 #define CONFIG_LCD                     1
 
@@ -92,16 +94,15 @@
  * data on the serial line may interrupt the boot sequence.
  */
 #define CONFIG_BOOTDELAY               0
-#define CONFIG_ZERO_BOOTDELAY_CHECK    1
-#define CONFIG_AUTOBOOT                        1
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_AUTOBOOT
 
 /*
  * After booting the board for the first time, new ethernet addresses
  * should be generated and assigned to the environment variables
  * "ethaddr" and "eth1addr". This is normally done during production.
  */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE  1
-#define CONFIG_NET_MULTI               1
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
 
 /*
  * BOOTP/DHCP options
@@ -109,8 +110,6 @@
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 
-#define CONFIG_DOS_PARTITION           1
-
 /*
  * Command line configuration.
  */
@@ -124,13 +123,14 @@
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_NET
 
-#define CONFIG_ATMEL_USART             1
-#define CONFIG_MACB                    1
-#define CONFIG_PORTMUX_PIO             1
+#define CONFIG_ATMEL_USART
+#define CONFIG_MACB
+#define CONFIG_PORTMUX_PIO
 #define CONFIG_SYS_NR_PIOS                     5
-#define CONFIG_SYS_HSDRAMC                     1
-#define CONFIG_MMC                     1
-#define CONFIG_ATMEL_MCI               1
+#define CONFIG_SYS_HSDRAMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#define CONFIG_GENERIC_MMC
 
 #if defined(CONFIG_LCD)
 #define CONFIG_CMD_BMP
@@ -151,8 +151,8 @@
 
 #define CONFIG_NR_DRAM_BANKS           1
 
-#define CONFIG_SYS_FLASH_CFI                   1
-#define CONFIG_FLASH_CFI_DRIVER                1
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
 
 #define CONFIG_SYS_FLASH_BASE                  0x00000000
 #define CONFIG_SYS_FLASH_SIZE                  0x800000
@@ -160,6 +160,7 @@
 #define CONFIG_SYS_MAX_FLASH_SECT              135
 
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_TEXT_BASE           0x00000000
 
 #define CONFIG_SYS_INTRAM_BASE                 INTERNAL_SRAM_BASE
 #define CONFIG_SYS_INTRAM_SIZE                 INTERNAL_SRAM_SIZE
@@ -168,7 +169,7 @@
 #define CONFIG_SYS_FRAM_BASE                   0x08000000
 #define CONFIG_SYS_FRAM_SIZE                   0x20000
 
-#define CONFIG_ENV_IS_IN_FLASH         1
+#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SIZE                        65536
 #define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
 
@@ -186,7 +187,7 @@
 #define CONFIG_SYS_CBSIZE                      256
 #define CONFIG_SYS_MAXARGS                     16
 #define CONFIG_SYS_PBSIZE                      (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP                    1
+#define CONFIG_SYS_LONGHELP
 
 #define CONFIG_SYS_MEMTEST_START               EBI_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END                 (CONFIG_SYS_MEMTEST_START + 0x1f00000)