at91sam9260ek: move board id setup to config header

[karo-tx-uboot.git] / include / configs / pcs440ep.h

diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 000ae5cd7d48257af80111f7ca04db801a290f51..351ff5a22bf0d137f2e0e85500476feef452f949 100644 (file)
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -40,6 +40,9 @@
 #define CONFIG_440EP           1       /* Specific PPC440EP support    */
 #define CONFIG_440             1       /* ... PPC440 family            */
 #define CONFIG_4xx             1       /* ... PPC4xx family            */
+
+#define        CONFIG_SYS_TEXT_BASE    0xFFFA0000
+
 #define CONFIG_SYS_CLK_FREQ    33333333    /* external freq to pll     */
 
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f     */
@@ -60,7 +63,6 @@
 #define CONFIG_SYS_PCI_MEMBASE3        CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
 
 /*Don't change either of these*/
-#define CONFIG_SYS_PERIPHERAL_BASE     0xef600000          /* internal peripherals*/
 #define CONFIG_SYS_PCI_BASE            0xe0000000          /* internal PCI regs*/
 /*Don't change either of these*/
 
@@ -72,19 +74,20 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_INIT_RAM_DCACHE     1               /* d-cache as init ram  */
 #define CONFIG_SYS_INIT_RAM_ADDR       0x70000000              /* DCache       */
-#define CONFIG_SYS_INIT_RAM_END        (4 << 10)
-#define CONFIG_SYS_GBL_DATA_SIZE       256                     /* num bytes initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       (4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX      1       /* Use UART0                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #undef CONFIG_SYS_EXT_SERIAL_CLOCK             /* no external clk used         */
 #define CONFIG_BAUDRATE                115200
-#define CONFIG_SERIAL_MULTI     1
-/*define this if you want console on UART1*/
-#undef CONFIG_UART1_CONSOLE
 
 #define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -138,6 +141,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C                1           /* I2C with hardware support        */
 #undef CONFIG_SOFT_I2C                     /* I2C bit-banged           */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #define CONFIG_SYS_I2C_SPEED           100000  /* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE           0x7F
 
@@ -220,7 +224,6 @@
 
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII             1       /* MII PHY management           */
-#define CONFIG_NET_MULTI        1      /* required for netconsole      */
 #define CONFIG_HAS_ETH1                1       /* add support for "eth1addr"   */
 #define CONFIG_PHY_ADDR                1       /* PHY address, See schematics  */
 #define CONFIG_PHY1_ADDR        2
@@ -440,14 +443,6 @@
 }                                                                                      \
 }
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */