at91sam9260ek: move board id setup to config header

[karo-tx-uboot.git] / include / configs / pf5200.h

diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h
index 8ca55d78ecc58899dfab06aa3deeda4705c89d21..4a985456d9b5feb60c48c5a48ca5277489224a40 100644 (file)
--- a/include/configs/pf5200.h
+++ b/include/configs/pf5200.h
@@ -44,10 +44,11 @@
 #define CONFIG_PF5200          1       /* ... on PF5200  board */
 #define CONFIG_MPC5200_DDR     1       /* ... use DDR RAM      */
 
-#define CONFIG_SYS_MPC5XXX_CLKIN       33000000        /* ... running at 33.000000MHz */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xFFF00000
+#endif
 
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM          0x02    /* Software reboot           */
+#define CONFIG_SYS_MPC5XXX_CLKIN       33000000        /* ... running at 33.000000MHz */
 
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
 /*
@@ -61,7 +62,6 @@
 #endif
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
 
-#ifdef CONFIG_MPC5200          /* MPC5100 PCI is not supported yet. */
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
@@ -82,12 +82,10 @@
 
 #define CONFIG_MII             1
 #if 0                          /* test-only !!! */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_EEPRO100                1
 #define CONFIG_SYS_RX_ETH_BUFFER       8       /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X         1
 #endif
-#endif
 
 /* Partitions */
 #define CONFIG_MAC_PARTITION
@@ -121,16 +119,14 @@
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IDE
 
-#ifdef CONFIG_MPC5200
 #define CONFIG_CMD_PCI
-#endif
 
 
-#if (TEXT_BASE == 0xFF000000)  /* Boot low with 16 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF000000)       /* Boot low with 16 MB Flash */
 #   define CONFIG_SYS_LOWBOOT          1
 #   define CONFIG_SYS_LOWBOOT16        1
 #endif
-#if (TEXT_BASE == 0xFF800000)  /* Boot low with  8 MB Flash */
+#if (CONFIG_SYS_TEXT_BASE == 0xFF800000)       /* Boot low with  8 MB Flash */
 #   define CONFIG_SYS_LOWBOOT          1
 #   define CONFIG_SYS_LOWBOOT08        1
 #endif
@@ -166,12 +162,10 @@
 
 #define CONFIG_BOOTCOMMAND     "run flash_vxworks0"
 
-#if defined(CONFIG_MPC5200)
 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK         /* define for 133MHz speed */
-#endif
 /*
  * I2C configuration
  */
@@ -226,13 +220,12 @@
 
 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_SIZE       /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -289,13 +282,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
 
 #define CONFIG_SYS_BOOTCS_START        CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE         CONFIG_SYS_FLASH_SIZE