*
* Configuration settings for the Dave/DENX QongEVB-LITE board.
*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/arch/mx31-regs.h>
+#include <asm/arch/imx-regs.h>
- /* High Level Configuration Options */
-#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
-#define CONFIG_MX31 1 /* in a mx31 */
-#define CONFIG_QONG 1
-#define CONFIG_MX31_HCLK_FREQ 26000000 /* 26MHz */
-#define CONFIG_MX31_CLK32 32768
+/* High Level Configuration Options */
+#define CONFIG_ARM1136 /* This is an arm1136 CPU core */
+#define CONFIG_MX31 /* in a mx31 */
+#define CONFIG_QONG
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
+#define CONFIG_SYS_TEXT_BASE 0xa0000000
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1536 * 1024)
/*
* Hardware drivers
*/
-#define CONFIG_MXC_UART 1
-#define CONFIG_SYS_MX31_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
-#define CONFIG_MX31_GPIO
+#define CONFIG_MXC_GPIO
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
#define CONFIG_MXC_SPI
#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH)
-#define CONFIG_RTC_MC13783
+#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_RTC_MC13XXX
-#define CONFIG_FSL_PMIC
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 0
#define CONFIG_FSL_PMIC_CLK 100000
-#define CONFIG_FSL_PMIC_MODE (SPI_MODE_2 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN 32
/* FPGA */
-#define CONFIG_QONG_FPGA 1
+#define CONFIG_FPGA
+#define CONFIG_QONG_FPGA
#define CONFIG_FPGA_BASE (CS1_BASE)
+#define CONFIG_FPGA_LATTICE
+#define CONFIG_FPGA_COUNT 1
#ifdef CONFIG_QONG_FPGA
/* Ethernet */
-#define CONFIG_DNET 1
+#define CONFIG_DNET
#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)
-#define CONFIG_NET_MULTI 1
/* Framebuffer and LCD */
-#define CONFIG_LCD
+#define CONFIG_VIDEO
+#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_MX3
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define LCD_BPP LCD_COLOR16
-#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
-#define CONFIG_DISPLAY_COM57H5M10XRC
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
+
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT 2
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
/*
* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_PING
+#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_SPI
-#define CONFIG_CMD_DATE
-#define BOARD_LATE_INIT
+#define CONFIG_CMD_UNZIP
-/*
- * You can compile in a MAC address and your custom net settings by using
- * the following syntax.
- *
- * #define CONFIG_ETHADDR xx:xx:xx:xx:xx:xx
- * #define CONFIG_SERVERIP <server ip>
- * #define CONFIG_IPADDR <board ip>
- * #define CONFIG_GATEWAYIP <gateway ip>
- * #define CONFIG_NETMASK <your netmask>
- */
+#define CONFIG_BOARD_LATE_INIT
#define CONFIG_BOOTDELAY 5
#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
-#define xstr(s) str(s)
-#define str(s) #s
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs}\0" \
"uboot_addr=A0000000\0" \
- "kernel_addr=A00A0000\0" \
+ "kernel_addr=A00C0000\0" \
"ramdisk_addr=A0300000\0" \
"u-boot=qong/u-boot.bin\0" \
"kernel_addr_r=80800000\0" \
"bootm\0" \
"bootcmd=run flash_self\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
- "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \
+ "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
- xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
+ __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
+ "videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000," \
+ "le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296," \
+ "vmode:0\0" \
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-#define CONFIG_MISC_INIT_R 1
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
+#define CONFIG_MISC_INIT_R
/*-----------------------------------------------------------------------
* Physical Memory Map
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */
-#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
* CFI FLASH driver setup
*/
/* Flash memory is CFI compliant */
-#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_SYS_FLASH_CFI
/* Use drivers/cfi_flash.c */
-#define CONFIG_FLASH_CFI_DRIVER 1
+#define CONFIG_FLASH_CFI_DRIVER
/* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/* Use hardware sector protection */
-#define CONFIG_SYS_FLASH_PROTECTION 1
+#define CONFIG_SYS_FLASH_PROTECTION
/*
* Filesystem
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
+ "nand0=gen_nand"
#define MTDPARTS_DEFAULT \
- "mtdparts=physmap-flash.0:384k(U-Boot),128k(env1)," \
- "128k(env2),2432k(kernel),13m(ramdisk),-(user)"
+ "mtdparts=physmap-flash.0:" \
+ "512k(U-Boot),128k(env1),128k(env2)," \
+ "2304k(kernel),13m(ramdisk),-(user);" \
+ "gen_nand:" \
+ "128m(nand)"
-/* additions for new relocation code, must added to all boards */
-#undef CONFIG_SYS_ARM_WITHOUT_RELOC /* This board is tested with relocation support */
+/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_END IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
-#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_BOARD_EARLY_INIT_F
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff