mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width

[karo-tx-uboot.git] / include / configs / tam3517-common.h

diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index c297827d80c4efbd723007cb2a221fdf7d268c52..eda536b8661c5943629ab1960437c74e86b7c243 100644 (file)
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -16,6 +16,7 @@
 #define CONFIG_OMAP            /* in a TI OMAP core */
 #define CONFIG_OMAP34XX                /* which is a 34XX */
 #define CONFIG_OMAP_GPIO
+#define CONFIG_OMAP_COMMON
 
 #define CONFIG_SYS_TEXT_BASE 0x80008000
 
@@ -116,14 +117,13 @@
 #undef CONFIG_CMD_IMLS
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED           400000
-#define CONFIG_SYS_I2C_SLAVE           1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED    400000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE    1
+#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50            /* base address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1               /* bytes of address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW    0x07
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
 
 /*
  * Board NAND Info.
@@ -168,7 +168,6 @@
  */
 #define CONFIG_SYS_TIMERBASE           OMAP34XX_GPT2
 #define CONFIG_SYS_PTV                 2       /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ                  1000
 
 /*
  * Physical Memory Map
@@ -187,7 +186,6 @@
 #define PISMO1_NAND_SIZE               GPMC_SIZE_128M
 
 #define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
 #define CONFIG_ENV_IS_IN_NAND
 #define SMNAND_ENV_OFFSET              0x180000 /* environment starts here */
 
@@ -214,7 +212,6 @@
 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 #define CONFIG_MII
 #define CONFIG_EMAC_MDIO_PHY_NUM       0
-#define CONFIG_BOOTP_DEFAULT
 #define CONFIG_BOOTP_DNS
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
@@ -252,6 +249,7 @@
 #define CONFIG_SPL_BSS_MAX_SIZE                0x80000
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
 #define CONFIG_SYS_NAND_PAGE_COUNT     64
 #define CONFIG_SYS_NAND_PAGE_SIZE      2048
 #define CONFIG_SYS_NAND_OOBSIZE                64
@@ -263,6 +261,7 @@
                                         56, 57, 58, 59, 60, 61, 62, 63}
 #define CONFIG_SYS_NAND_ECCSIZE                256
 #define CONFIG_SYS_NAND_ECCBYTES       3
+#define CONFIG_NAND_OMAP_ECCSCHEME     OMAP_ECC_HAM1_CODE_SW
 
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
 
@@ -370,7 +369,7 @@ struct tam3517_module_info {
 
 #define TAM3517_READ_EEPROM(info, ret) \
 do {                                                           \
-       i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);   \
+       i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
        if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
                (void *)info, sizeof(*info)))                   \
                ret = 1;                                        \