/*
* (C) Copyright 2002-2005
- * Gary Jennejohn <gj@denx.de>
+ * Gary Jennejohn <garyj@denx.de>
*
* Configuation settings for the TRAB board.
*
* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_ARM920T 1 /* This is an arm920t CPU */
-#define CONFIG_S3C2400 1 /* in a SAMSUNG S3C2400 SoC */
-#define CONFIG_TRAB 1 /* on a TRAB Board */
-#undef CONFIG_TRAB_50MHZ /* run the CPU at 50 MHz */
-#define LITTLEENDIAN 1 /* used by usb_ohci.c */
+#define CONFIG_ARM920T 1 /* This is an arm920t CPU */
+#define CONFIG_S3C24X0 1 /* in a SAMSUNG S3C24x0-type SoC */
+#define CONFIG_S3C2400 1 /* specifically a SAMSUNG S3C2400 SoC */
+#define CONFIG_TRAB 1 /* on a TRAB Board */
+#undef CONFIG_TRAB_50MHZ /* run the CPU at 50 MHz */
/* automatic software updates (see board/trab/auto_update.c) */
#define CONFIG_AUTO_UPDATE 1
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
-#define CFG_DEVICE_NULLDEV 1 /* enble null device */
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* enble null device */
#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
* address 0x54 with 8bit addressing
***********************************************************/
#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CFG_I2C_SPEED 100000 /* I2C speed */
-#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
+#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave addr */
-#define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM address */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* 1 address byte */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 1 address byte */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* 8 bytes page write mode on 24C04 */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 bytes page write mode on 24C04 */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* USB stuff */
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_STORAGE 1
#define CONFIG_DOS_PARTITION 1
-#undef CFG_USB_OHCI_BOARD_INIT
-#define CFG_USB_OHCI_CPU_INIT 1
-#define CFG_USB_OHCI_REGS_BASE S3C24X0_USB_HOST_BASE
-#define CFG_USB_OHCI_SLOT_NAME "s3c2400"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x14200000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "s3c2400"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
-#define CS8900_BASE 0x07000300 /* agrees with WIN CE PA */
-#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
+#define CONFIG_NET_MULTI
+#define CONFIG_CS8900 /* we have a CS8900 on-board */
+#define CONFIG_CS8900_BASE 0x07000300 /* agrees with WIN CE PA */
+#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */
#define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on TRAB */
#define CONFIG_HWFLOW /* include RTS/CTS flow control support */
/* Use s3c2400's RTC */
#define CONFIG_RTC_S3C24X0 1
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
#ifdef CONFIG_HWFLOW
-#define CONFIG_COMMANDS_ADD_HWFLOW CFG_CMD_HWFLOW
-#else
-#define CONFIG_COMMANDS_ADD_HWFLOW 0
+ #define CONFIG_CMD_HWFLOW
#endif
#ifdef CONFIG_VFD
-#define CONFIG_COMMANDS_ADD_VFD CFG_CMD_VFD
-#else
-#define CONFIG_COMMANDS_ADD_VFD 0
+ #define CONFIG_CMD_VFD
#endif
#ifdef CONFIG_DRIVER_S3C24X0_I2C
-#define CONFIG_COMMANDS_ADD_EEPROM CFG_CMD_EEPROM
-#define CONFIG_COMMANDS_I2C CFG_CMD_I2C
-#else
-#define CONFIG_COMMANDS_ADD_EEPROM 0
-#define CONFIG_COMMANDS_I2C 0
+ #define CONFIG_CMD_EEPROM
+ #define CONFIG_CMD_I2C
#endif
#ifndef USE_920T_MMU
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & ~CFG_CMD_CACHE) | \
- CONFIG_COMMANDS_ADD_HWFLOW | \
- CONFIG_COMMANDS_ADD_VFD | \
- CONFIG_COMMANDS_ADD_EEPROM | \
- CONFIG_COMMANDS_I2C | \
- CFG_CMD_BSP | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_FAT | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP | \
- CFG_CMD_USB )
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CONFIG_COMMANDS_ADD_HWFLOW | \
- CONFIG_COMMANDS_ADD_VFD | \
- CONFIG_COMMANDS_ADD_EEPROM | \
- CONFIG_COMMANDS_I2C | \
- CFG_CMD_BSP | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_FAT | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP | \
- CFG_CMD_USB )
+ #undef CONFIG_CMD_CACHE
#endif
-/* moved up */
-#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/* moved up */
+#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
#define CONFIG_BOOTDELAY 5
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
#define CONFIG_BOOTCOMMAND "burn_in"
#ifndef CONFIG_FLASH_8MB /* current config: 16 MB flash */
-#ifdef CFG_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_EXTRA_ENV_SETTINGS \
"nfs_args=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"mdm_init1=ATZ\0" \
"mdm_init2=ATS0=1\0" \
"mdm_flow_control=rts/cts\0"
-#else /* !CFG_HUSH_PARSER */
+#else /* !CONFIG_SYS_HUSH_PARSER */
#define CONFIG_EXTRA_ENV_SETTINGS \
"nfs_args=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"mdm_init1=ATZ\0" \
"mdm_init2=ATS0=1\0" \
"mdm_flow_control=rts/cts\0"
-#endif /* CFG_HUSH_PARSER */
-#else /* CONFIG_FLASH_8MB => 8 MB flash */
-#ifdef CFG_HUSH_PARSER
+#endif /* CONFIG_SYS_HUSH_PARSER */
+#else /* CONFIG_FLASH_8MB => 8 MB flash */
+#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_EXTRA_ENV_SETTINGS \
"nfs_args=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"mdm_init1=ATZ\0" \
"mdm_init2=ATS0=1\0" \
"mdm_flow_control=rts/cts\0"
-#else /* !CFG_HUSH_PARSER */
+#else /* !CONFIG_SYS_HUSH_PARSER */
#define CONFIG_EXTRA_ENV_SETTINGS \
"nfs_args=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"mdm_init1=ATZ\0" \
"mdm_init2=ATS0=1\0" \
"mdm_flow_control=rts/cts\0"
-#endif /* CFG_HUSH_PARSER */
+#endif /* CONFIG_SYS_HUSH_PARSER */
#endif /* CONFIG_FLASH_8MB */
#if 1 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nEnter password - autoboot in %d sec...\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "R" /* 1st "password" */
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "TRAB # " /* Monitor Command Prompt */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "TRAB # " /* Monitor Command Prompt */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0C000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0D000000 /* 16 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0C000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0D000000 /* 16 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_LOAD_ADDR 0x0CF00000 /* default load address */
-#define CFG_LOAD_ADDR 0x0CF00000 /* default load address */
-
-#ifdef CONFIG_TRAB_50MHZ
-/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
-/* it to wrap 100 times (total 1562500) to get 1 sec. */
-/* this should _really_ be calculated !! */
-#define CFG_HZ 1562500
-#else
-/* the PWM TImer 4 uses a counter of 10390 for 10 ms, so we need */
-/* it to wrap 100 times (total 1039000) to get 1 sec. */
-/* this should _really_ be calculated !! */
-#define CFG_HZ 1039000
-#endif
+#define CONFIG_SYS_HZ 1000
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_MISC_INIT_R /* have misc_init_r() function */
#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
#endif
-#define CFG_FLASH_BASE 0x00000000 /* Flash Bank #1 */
+#define CONFIG_SYS_FLASH_BASE 0x00000000 /* Flash Bank #1 */
/* The following #defines are needed to get flash environment right */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10)
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 << 10)
/* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=0"
/* production flash layout */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#ifndef CONFIG_FLASH_8MB
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#else
-#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#endif
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (15*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (15*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
/* Address and size of Primary Environment Sector */
#ifndef CONFIG_FLASH_8MB
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000)
-#define CFG_ENV_SIZE 0x4000
-#define CFG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_SECT_SIZE 0x20000
#else
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000)
-#define CFG_ENV_SIZE 0x4000
-#define CFG_ENV_SECT_SIZE 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000)
+#define CONFIG_ENV_SIZE 0x4000
+#define CONFIG_ENV_SECT_SIZE 0x4000
#endif
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_ADDR+CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
/* Initial value of the on-board touch screen brightness */
-#define CFG_BRIGHTNESS 0x20
+#define CONFIG_SYS_BRIGHTNESS 0x20
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff