tricorder: read kernel directly from NAND

[karo-tx-uboot.git] / include / configs / tricorder.h

diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index a3d8f12f9765a1e79089a35a4bda4001160f1a03..aab1bf1902b40f8382ca78d6fd47da324e5d6408 100644 (file)
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -39,6 +39,9 @@
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
+#define CONFIG_SILENT_CONSOLE
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
 /* Clock Defines */
 #define V_OSCK                         26000000 /* Clock output from T2 */
 #define V_SCLK                         (V_OSCK >> 1)
@@ -57,6 +60,23 @@
 
 /* Hardware drivers */
 
+/* GPIO support */
+#define CONFIG_OMAP_GPIO
+
+/* LED support */
+#define CONFIG_STATUS_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_CMD_LED                 /* LED command */
+#define STATUS_LED_BIT                 (1 << 0)
+#define STATUS_LED_STATE               STATUS_LED_ON
+#define STATUS_LED_PERIOD              (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1                        (1 << 1)
+#define STATUS_LED_STATE1              STATUS_LED_ON
+#define STATUS_LED_PERIOD1             (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT2                        (1 << 2)
+#define STATUS_LED_STATE2              STATUS_LED_ON
+#define STATUS_LED_PERIOD2             (CONFIG_SYS_HZ / 2)
+
 /* NS16550 Configuration */
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
@@ -148,7 +168,10 @@
 
 /* Environment information (this is the common part) */
 
-#define CONFIG_BOOTDELAY               3
+#define CONFIG_BOOTDELAY               0
+
+/* hang() the board on panic() */
+#define CONFIG_PANIC_HANG
 
 /* environment placement (for NAND), is different for FLASHCARD but does not
  * harm there */
@@ -237,9 +260,10 @@
        "loaduimage_ubi=ubi part ubi; " \
                "ubifsmount ubi:root; " \
                "ubifsload ${loadaddr} /boot/uImage\0" \
+       "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \
        "nandboot=echo Booting from nand ...; " \
                "run nandargs; " \
-               "run loaduimage_ubi; " \
+               "run loaduimage_nand; " \
                "bootm ${loadaddr}\0" \
        "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
                        "if run loadbootscript; then " \
@@ -269,9 +293,9 @@
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE            (CONFIG_SYS_CBSIZE)
 
-#define CONFIG_SYS_MEMTEST_START       (OMAP34XX_SDRC_CS0 + 0x07000000)
+#define CONFIG_SYS_MEMTEST_START       (OMAP34XX_SDRC_CS0 + 0x00000000)
 #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + \
-                                       0x01000000) /* 16MB */
+                                       0x07000000) /* 112 MB */
 
 #define CONFIG_SYS_LOAD_ADDR           (OMAP34XX_SDRC_CS0 + 0x02000000)
 
@@ -311,6 +335,7 @@
 #define CONFIG_SPL_NAND_SIMPLE
 
 #define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
@@ -359,4 +384,6 @@
 #define CONFIG_SYS_SPL_MALLOC_START    0x80208000
 #define CONFIG_SYS_SPL_MALLOC_SIZE     0x100000        /* 1 MB */
 
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_SCRATCH     0x81000000
 #endif /* __CONFIG_H */