*
* Configuration settings for the HALE TT-01 board.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_ARM1136
#define CONFIG_MX31
-#define CONFIG_MX31_HCLK_FREQ 26000000
-#define CONFIG_MX31_CLK32 32768
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
/* default load address, 1MB up the road */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1+0x100000)
-/* The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
/* Size of malloc() pool, make sure possible frame buffer fits */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 10*1024*1024)
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE (8 * 1024) /* smaller for faster access */
+#define CONFIG_ENV_SIZE (128 * 1024)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_MXC_GPIO
/* MC13783 connected to CSPI3 and SS0 */
-#define CONFIG_PMIC
-#define CONFIG_PMIC_SPI
-#define CONFIG_PMIC_FSL
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 2
#define CONFIG_FSL_PMIC_CS 0
/* console is UART2 on TT-01 */
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/* ethernet setup for the onboard smc9118 */
#define CONFIG_MII
#define CONFIG_SMC911X_BASE (CS4_BASE+0x200000)
#define CONFIG_SMC911X_16_BIT
+/* mmc driver */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MXC_MMC
+#define CONFIG_MXC_MCI_REGS_BASE SDHC1_BASE_ADDR
+
+/* video support */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MX3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+/* splash image won't work with NAND boot, use preboot script */
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_CONSOLE_EXTRA_INFO /* display additional board info */
+#define CONFIG_VGA_AS_SINGLE_DEVICE /* display is an output only device */
+
+/* allow stdin, stdout and stderr variables to redirect output */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SILENT_CONSOLE /* UARTs used externally (release) */
+#define CONFIG_SYS_DEVICE_NULLDEV /* allow console to be turned off */
+#define CONFIG_PREBOOT
+
+/* allow decompressing max. 4MB */
+#define CONFIG_VIDEO_BMP_GZIP
+/* this is not only used by cfb_console.c for the logo, but also in cmd_bmp.c */
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4*1024*1024)
+
/*
* Command definition
*/
* the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports
* a software locking scheme.
*/
+#define CONFIG_CMD_BMP
#define CONFIG_BOOTDELAY 3
* currently a default setting for booting via script is implemented
* set user to login name and serverip to tftp host, define your
* boot behaviour in bootscript.loginname
+ *
+ * TT-01 board specific TFT setup (used by drivers/video/mx3fb.c)
+ *
+ * This set-up is for the L5F30947T04 by Epson, which is
+ * 800x480, 33MHz pixel clock, 60Hz vsync, 31.6kHz hsync
+ * sync must be set to: DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootcmd=dhcp bootscript.$(user); source\0"
+"videomode=epson\0" \
+"epson=video=ctfb:x:800,y:480,depth:16,mode:0,pclk:30076," \
+ "le:215,ri:1,up:32,lo:13,hs:7,vs:10,sync:100663296,vmode:0\0" \
+"bootcmd=dhcp bootscript.${user}; source\0"
#define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */
#define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */
/* Miscellaneous configurable options */
-#define CONFIG_HUSH_PARSER
-#define CONFIG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "TT01> "
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_HZ 1000
-
#define CONFIG_CMDLINE_EDITING
+/* MMC boot support */
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
#define CONFIG_NAND_MXC
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_MAX_CHIPS 1
/*
* actually this is nothing someone wants to configure!
projects / karo-tx-uboot.git / blobdiff