* (C) Copyright 2009
* Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
*/
#define CONFIG_SPEAR600 /* SPEAr600 SoC */
#define CONFIG_X600 /* on X600 board */
+#define CONFIG_SYS_GENERIC_BOARD
#include <asm/arch/hardware.h>
/* Ethernet config options */
#define CONFIG_MII
-#define CONFIG_DESIGNWARE_ETH
-#define CONFIG_NET_MULTI
#define CONFIG_PHYLIB
#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_SPEAR_GPIO
/* I2C config options */
-#define CONFIG_HARD_I2C
-#define CONFIG_DW_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DW
+#define CONFIG_SYS_I2C_BASE 0xD0200000
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 0x02
#define CONFIG_I2C_CHIPADDRESS 0x50
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_GPIO
#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MII
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
#define CONFIG_CMD_SAVES
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_LZO
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <config_cmd_default.h>
-
#define CONFIG_BOOTDELAY 3
#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
#define CONFIG_LOOPW /* enable loopw command */
#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_STOP_STR " "
-#define CONFIG_AUTOBOOT_PROMPT \
- "Hit SPACE in %d seconds to stop autoboot.\n", bootdelay
#define CONFIG_SYS_MEMTEST_START 0x00800000
#define CONFIG_SYS_MEMTEST_END 0x04000000
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
#define CONFIG_IDENT_STRING "-SPEAr"
#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "X600> "
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR 0x00800000
#define CONFIG_SYS_CONSOLE_INFO_QUIET
-#define CONFIG_SYS_64BIT_VSPRINTF
/* Use last 2 lwords in internal SRAM for bootcounter */
#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_SYS_BOOTCOUNT_ADDR 0xd2801ff8
+#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SRAM_BASE + \
+ CONFIG_SRAM_SIZE)
#define CONFIG_HOSTNAME x600
#define CONFIG_UBI_PART ubi0
#define CONFIG_UBIFS_VOLUME rootfs
-#define xstr(s) str(s)
-#define str(s) #s
-
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:64M(ubi0),64M(ubi1)"
#define CONFIG_EXTRA_ENV_SETTINGS \
"u-boot_addr=1000000\0" \
- "u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.spr\0" \
+ "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.spr\0" \
"load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) " +${filesize};"\
- "erase " xstr(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \
- "cp.b ${u-boot_addr} " xstr(CONFIG_SYS_MONITOR_BASE) \
+ "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
+ " +${filesize};" \
+ "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \
+ "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \
" ${filesize};" \
- "protect on " xstr(CONFIG_SYS_MONITOR_BASE) \
+ "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize}\0" \
"upd=run load update\0" \
- "ubifs=" xstr(CONFIG_HOSTNAME) "/ubifs.img\0" \
- "part=" xstr(CONFIG_UBI_PART) "\0" \
- "vol=" xstr(CONFIG_UBIFS_VOLUME) "\0" \
+ "ubifs=" __stringify(CONFIG_HOSTNAME) "/ubifs.img\0" \
+ "part=" __stringify(CONFIG_UBI_PART) "\0" \
+ "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \
"load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \
"update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \
" ${filesize}\0" \
"saveenv;boot\0" \
"ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \
"root=ubi0:rootfs rootfstype=ubifs\0" \
- "kernel=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
+ "kernel=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
"kernel_fs=/boot/uImage \0" \
"kernel_addr=1000000\0" \
- "dtb=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" \
- "dtb_fs=/boot/" xstr(CONFIG_HOSTNAME) ".dtb\0" \
+ "dtb=" __stringify(CONFIG_HOSTNAME) "/" \
+ __stringify(CONFIG_HOSTNAME) ".dtb\0" \
+ "dtb_fs=/boot/" __stringify(CONFIG_HOSTNAME) ".dtb\0" \
"dtb_addr=1800000\0" \
"load_kernel=tftp ${kernel_addr} ${kernel}\0" \
"load_dtb=tftp ${dtb_addr} ${dtb}\0" \
#define PHYS_SDRAM_1_MAXSIZE 0x40000000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xD2800000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000
+#define CONFIG_SRAM_BASE 0xd2800000
+/* Preserve the last 2 lwords for the boot-counter */
+#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8)
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* SPL related defines
*/
-#define CONFIG_SPL
-#define CONFIG_SPL_TEXT_BASE 0xd2800b00
+#define CONFIG_SPL_TEXT_BASE 0xd2800b00
+#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00)
#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear"
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds"
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NOR_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT /* image.c */
#define CONFIG_SPL_LIBGENERIC_SUPPORT /* string.c */
projects / karo-tx-uboot.git / blobdiff