#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EP 1 /* Specifc 405EP support*/
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_PHY_ADDR 0x01 /* PHY address */
#define CONFIG_HAS_ETH1 1
#define CONFIG_PHY1_ADDR 0x11 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PHY_RESET 1
#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOG
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */
/* Define here the base-addresses of the UARTs to test in POST */
-#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE}
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_SYS_BASE_BAUD 691200
+#define CONFIG_SYS_BASE_BAUD 691200
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */
-#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* reserve some memory for POST and BOOT limit info */
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16)
/* extra data in OCM */
-#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4)
-#define CONFIG_SYS_POST_MAGIC (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 8)
-#define CONFIG_SYS_POST_VAL (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 12)
+#define CONFIG_SYS_POST_MAGIC \
+ (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 8)
+#define CONFIG_SYS_POST_VAL \
+ (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 12)
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CONFIG_SYS_GPIO0_OSRH 0x15555550 /* Chip selects */
-#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* UART_DTR-pin 27 alt out */
-#define CONFIG_SYS_GPIO0_ISR1H 0x10000041 /* Pin 2, 12 is input */
-#define CONFIG_SYS_GPIO0_ISR1L 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_OSRL 0x15555550 /* Chip selects */
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* UART_DTR-pin 27 alt out */
+#define CONFIG_SYS_GPIO0_ISR1L 0x10000041 /* Pin 2, 12 is input */
+#define CONFIG_SYS_GPIO0_ISR1H 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
#define CONFIG_SYS_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */
#define CONFIG_SYS_GPIO0_ODR 0x00000000
#define CONFIG_SYS_TIME_POST 5000
#define CONFIG_SYS_TIME_FACTORY_RESET 10000
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
projects / karo-tx-uboot.git / blobdiff