mxs: spl: remove duplicate debug messages

diff --git a/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c b/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c
index daae30c451058cb21854106cb336d1d9d2e72cb3..561c04db279f9161979fb23e310d3c7c295a46c0 100644 (file)
--- a/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c
+++ b/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c
@@ -324,8 +324,6 @@ static void mxs_src_power_init(void)
 {
        debug("SPL: Pre-Configuring power block\n");
 
-       debug("SPL: Pre-Configuring power block\n");
-
        /* Improve efficieny and reduce transient ripple */
        writel(POWER_LOOPCTRL_TOGGLE_DIF | POWER_LOOPCTRL_EN_CM_HYST |
                POWER_LOOPCTRL_EN_DF_HYST, &power_regs->hw_power_loopctrl_set);
@@ -370,8 +368,6 @@ static void mxs_power_init_4p2_params(void)
 {
        debug("SPL: Configuring common 4P2 regulator params\n");
 
-       debug("SPL: Configuring common 4P2 regulator params\n");
-
        /* Setup 4P2 parameters */
        clrsetbits_le32(&power_regs->hw_power_dcdc4p2,
                POWER_DCDC4P2_CMPTRIP_MASK | POWER_DCDC4P2_TRG_MASK,
@@ -596,8 +592,6 @@ static void mxs_power_init_dcdc_4p2_source(void)
 {
        debug("SPL: Switching DC-DC converters to 4P2\n");
 
-       debug("SPL: Switching DC-DC converters to 4P2\n");
-
        if (!(readl(&power_regs->hw_power_dcdc4p2) &
                POWER_DCDC4P2_ENABLE_DCDC)) {
                debug("SPL: Already switched - aborting\n");
@@ -695,8 +689,6 @@ static void mxs_boot_valid_5v(void)
 {
        debug("SPL: Booting from 5V supply\n");
 
-       debug("SPL: Booting from 5V supply\n");
-
        /*
         * Use VBUSVALID level instead of VDD5V_GT_VDDIO level to trigger a 5V
         * disconnect event. FIXME
@@ -739,8 +731,6 @@ static void mxs_batt_boot(void)
 {
        debug("SPL: Configuring power block to boot from battery\n");
 
-       debug("SPL: Configuring power block to boot from battery\n");
-
        clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT);
        clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_ENABLE_DCDC);
 
@@ -844,8 +834,6 @@ static void mxs_5v_boot(void)
 {
        debug("SPL: Configuring power block to boot from 5V input\n");
 
-       debug("SPL: Configuring power block to boot from 5V input\n");
-
        /*
         * NOTE: In original IMX-Bootlets, this also checks for VBUSVALID,
         * but their implementation always returns 1 so we omit it here.
@@ -907,8 +895,6 @@ static void mxs_init_batt_bo(void)
 {
        debug("SPL: Initialising battery brown-out level to 3.0V\n");
 
-       debug("SPL: Initialising battery brown-out level to 3.0V\n");
-
        /* Brownout at 3V */
        clrsetbits_le32(&power_regs->hw_power_battmonitor,
                POWER_BATTMONITOR_BRWNOUT_LVL_MASK,
@@ -928,8 +914,6 @@ static void mxs_switch_vddd_to_dcdc_source(void)
 {
        debug("SPL: Switching VDDD to DC-DC converters\n");
 
-       debug("SPL: Switching VDDD to DC-DC converters\n");
-
        clrsetbits_le32(&power_regs->hw_power_vdddctrl,
                POWER_VDDDCTRL_LINREG_OFFSET_MASK,
                POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW);
@@ -1011,8 +995,6 @@ static void mxs_enable_output_rail_protection(void)
 {
        debug("SPL: Enabling output rail protection\n");
 
-       debug("SPL: Enabling output rail protection\n");
-
        writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ |
                POWER_CTRL_VDDIO_BO_IRQ, &power_regs->hw_power_ctrl_clr);
 
@@ -1353,8 +1335,6 @@ void mxs_power_init(void)
 {
        debug("SPL: Initialising Power Block\n");
 
-       debug("SPL: Initialising Power Block\n");
-
        mxs_ungate_power();
 
        mxs_power_clock2xtal();