endif
# Specify the target for use in elftosb call
-ELFTOSB_TARGET-$(CONFIG_MX23) = imx23
-ELFTOSB_TARGET-$(CONFIG_MX28) = imx28
+MKIMAGE_TARGET-$(CONFIG_MX23) = mx23
+MKIMAGE_TARGET-$(CONFIG_MX28) = mx28
-$(OBJTREE)/u-boot.bd: $(SRCTREE)/$(CPUDIR)/$(SOC)/u-boot-$(ELFTOSB_TARGET-y).bd
+$(OBJTREE)/mxsimage.cfg: $(SRCTREE)/$(CPUDIR)/$(SOC)/mxsimage.$(MKIMAGE_TARGET-y).cfg
sed "s@OBJTREE@$(OBJTREE)@g" $^ > $@
-$(OBJTREE)/u-boot.sb: $(OBJTREE)/u-boot.bin $(OBJTREE)/spl/u-boot-spl.bin $(OBJTREE)/u-boot.bd
- elftosb -zf $(ELFTOSB_TARGET-y) -c $(OBJTREE)/u-boot.bd -o $(OBJTREE)/u-boot.sb
+$(OBJTREE)/u-boot.sb: $(OBJTREE)/u-boot.bin $(OBJTREE)/spl/u-boot-spl.bin $(OBJTREE)/mxsimage.cfg
+ $(OBJTREE)/tools/mkimage -n $(OBJTREE)/mxsimage.cfg -T mxsimage $@
SECTION 0x0 BOOTABLE
TAG LAST
- LOAD 0x0 spl/u-boot-spl.bin
+ LOAD 0x0 OBJTREE/spl/u-boot-spl.bin
CALL 0x14 0x0
- LOAD 0x40000100 u-boot.bin
+ LOAD 0x40000100 OBJTREE/u-boot.bin
CALL 0x40000100 0x0
SECTION 0x0 BOOTABLE
TAG LAST
- LOAD 0x0 spl/u-boot-spl.bin
+ LOAD 0x0 OBJTREE/spl/u-boot-spl.bin
LOAD IVT 0x8000 0x14
CALL HAB 0x8000 0x0
- LOAD 0x40000100 u-boot.bin
+ LOAD 0x40000100 OBJTREE/u-boot.bin
LOAD IVT 0x8000 0x40000100
CALL HAB 0x8000 0x0
clrsetbits_le32(&power_regs->hw_power_5vctrl,
POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
0x8 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
+
+ mxs_power_enable_4p2();
}
/**
*/
_reset:
+ /*
+ * If the CPU is configured in "Wait JTAG connection mode", the stack
+ * pointer is not configured and is zero. This will cause crash when
+ * trying to push data onto stack right below here. Load the SP and make
+ * it point to the end of OCRAM if the SP is zero.
+ */
+ cmp sp, #0x00000000
+ ldreq sp, =CONFIG_SYS_INIT_SP_ADDR
+
/*
* Store all registers on old stack pointer, this will allow us later to
* return to the BootROM and let the BootROM load U-Boot into RAM.
#include <linux/usb/gadget.h>
#include <linux/usb/musb.h>
#include <asm/omap_musb.h>
+#include <asm/davinci_rtc.h>
DECLARE_GLOBAL_DATA_PTR;
static void rtc32k_enable(void)
{
- struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
+ struct davinci_rtc *rtc = (struct davinci_rtc *)RTC_BASE;
/*
* Unlock the RTC's registers. For more details please see the
* RTC_SS section of the TRM. In order to unlock we need to
* write these specific values (keys) in this order.
*/
- writel(0x83e70b13, &rtc->kick0r);
- writel(0x95a4f1e0, &rtc->kick1r);
+ writel(RTC_KICK0R_WE, &rtc->kick0r);
+ writel(RTC_KICK1R_WE, &rtc->kick1r);
/* Enable the RTC 32K OSC by setting bits 3 and 6. */
writel((1 << 3) | (1 << 6), &rtc->osc);
#endif
mcr 15, 1, r0, c9, c0, 2
+
+ /* enable L2 cache */
+ mrc 15, 0, r0, c1, c0, 1
+ orr r0, r0, #2
+ mcr 15, 0, r0, c1, c0, 1
+
.endm /* init_l2cc */
/* AIPS setup - Only setup MPROTx registers.
#endif /* CONFIG_MX53 */
.endm
-.macro setup_wdog
- ldr r0, =WDOG1_BASE_ADDR
- mov r1, #0x30
- strh r1, [r0]
-.endm
-
ENTRY(lowlevel_init)
mov r10, lr
mov r4, #0 /* Fix R4 to 0 */
}
/* NOTREACHED */
}
+static u32 mxc_get_pll_pfd(enum pll_clocks pll, int pfd_num)
+{
+ u32 div;
+ u64 freq;
+
+ switch (pll) {
+ case PLL_BUS:
+ if (pfd_num == 3) {
+ /* No PFD3 on PPL2 */
+ return 0;
+ }
+ div = __raw_readl(&imx_ccm->analog_pfd_528);
+ freq = (u64)decode_pll(PLL_BUS, MXC_HCLK);
+ break;
+ case PLL_USBOTG:
+ div = __raw_readl(&imx_ccm->analog_pfd_480);
+ freq = (u64)decode_pll(PLL_USBOTG, MXC_HCLK);
+ break;
+ default:
+ /* No PFD on other PLL */
+ return 0;
+ }
+
+ return (freq * 18) / ((div & ANATOP_PFD_FRAC_MASK(pfd_num)) >>
+ ANATOP_PFD_FRAC_SHIFT(pfd_num));
+}
static u32 get_mcu_main_clk(void)
{
freq = decode_pll(PLL_BUS, MXC_HCLK);
break;
case 1:
- freq = PLL2_PFD2_FREQ;
+ freq = mxc_get_pll_pfd(PLL_BUS, 2);
break;
case 2:
- freq = PLL2_PFD0_FREQ;
+ freq = mxc_get_pll_pfd(PLL_BUS, 0);
break;
case 3:
- freq = PLL2_PFD2_DIV_FREQ;
+ /* static / 2 divider */
+ freq = mxc_get_pll_pfd(PLL_BUS, 2) / 2;
break;
default:
break;
static u32 get_uart_clk(void)
{
u32 reg, uart_podf;
- u32 freq = PLL3_80M;
+ u32 freq = decode_pll(PLL_USBOTG, MXC_HCLK) / 6; /* static divider */
reg = __raw_readl(&imx_ccm->cscdr1);
#ifdef CONFIG_MX6SL
if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL)
reg &= MXC_CCM_CSCDR2_ECSPI_CLK_PODF_MASK;
cspi_podf = reg >> MXC_CCM_CSCDR2_ECSPI_CLK_PODF_OFFSET;
- return PLL3_60M / (cspi_podf + 1);
+ return decode_pll(PLL_USBOTG, MXC_HCLK) / (8 * (cspi_podf + 1));
}
static u32 get_axi_clk(void)
if (cbcdr & MXC_CCM_CBCDR_AXI_SEL) {
if (cbcdr & MXC_CCM_CBCDR_AXI_ALT_SEL)
- root_freq = PLL2_PFD2_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
else
- root_freq = PLL3_PFD1_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_USBOTG, 1);
} else
root_freq = get_periph_clk();
root_freq = decode_pll(PLL_USBOTG, MXC_HCLK);
break;
case 2:
- root_freq = PLL2_PFD2_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
break;
case 3:
- root_freq = PLL2_PFD0_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 0);
break;
}
freq = decode_pll(PLL_BUS, MXC_HCLK);
break;
case 1:
- freq = PLL2_PFD2_FREQ;
+ freq = mxc_get_pll_pfd(PLL_BUS, 2);
break;
case 2:
- freq = PLL2_PFD0_FREQ;
+ freq = mxc_get_pll_pfd(PLL_BUS, 0);
break;
case 3:
- freq = PLL2_PFD2_DIV_FREQ;
+ /* static / 2 divider */
+ freq = mxc_get_pll_pfd(PLL_BUS, 2) / 2;
}
return freq / (podf + 1);
}
if (clk_sel)
- root_freq = PLL2_PFD0_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 0);
else
- root_freq = PLL2_PFD2_FREQ;
+ root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
return root_freq / (usdhc_podf + 1);
}
#include <asm/arch/omap.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
+#include <watchdog.h>
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_AM33XX) && defined(CONFIG_SPL_MUSB_NEW_SUPPORT)
arch_misc_init();
#endif
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
+#endif
#ifdef CONFIG_AM33XX
am33xx_spl_board_init();
#endif
#include <asm/arch/hardware.h>
void lowlevel_init(void)
+{
+}
+
+int arch_cpu_init(void)
{
zynq_slcr_unlock();
/* remap DDR to zero, FILTERSTART */
writel(0xC, &slcr_base->ddr_urgent);
zynq_slcr_lock();
+
+ return 0;
}
void reset_cpu(ulong addr)
unsigned int tcar2; /* offset 0x58 */
};
-/* RTC Registers */
-struct rtc_regs {
- unsigned int res[21];
- unsigned int osc; /* offset 0x54 */
- unsigned int res2[5];
- unsigned int kick0r; /* offset 0x6c */
- unsigned int kick1r; /* offset 0x70 */
-};
-
/* UART Registers */
struct uart_sys {
unsigned int resv1[21];
#endif
#define AT91_PMC_USBS_USB_PLLA (0x0) /* USB Clock Input is PLLA */
#define AT91_PMC_USBS_USB_UPLL (0x1) /* USB Clock Input is UPLL */
+#define AT91_PMC_USBS_USB_PLLB (0x1) /* USB Clock Input is PLLB, AT91SAM9N12 only */
+#define AT91_PMC_USB_DIV_2 (0x1 << 8) /* USB Clock divided by 2 */
#define AT91_PMC_USBDIV_8 (0x7 << 8) /* USB Clock divided by 8 */
#define AT91_PMC_USBDIV_10 (0x9 << 8) /* USB Clock divided by 10 */
#define AT91_RSTC_SR_NRSTL 0x00010000
+#define AT91_RSTC_RSTTYP (7 << 8) /* Reset Type */
+#define AT91_RSTC_RSTTYP_GENERAL (0 << 8)
+#define AT91_RSTC_RSTTYP_WAKEUP (1 << 8)
+#define AT91_RSTC_RSTTYP_WATCHDOG (2 << 8)
+#define AT91_RSTC_RSTTYP_SOFTWARE (3 << 8)
+#define AT91_RSTC_RSTTYP_USER (4 << 8)
+
#endif
#endif
-struct davinci_rtc {
- dv_reg second;
- dv_reg minutes;
- dv_reg hours;
- dv_reg day;
- dv_reg month; /* 0x10 */
- dv_reg year;
- dv_reg dotw;
- dv_reg resv1;
- dv_reg alarmsecond; /* 0x20 */
- dv_reg alarmminute;
- dv_reg alarmhour;
- dv_reg alarmday;
- dv_reg alarmmonth; /* 0x30 */
- dv_reg alarmyear;
- dv_reg resv2[2];
- dv_reg ctrl; /* 0x40 */
- dv_reg status;
- dv_reg irq;
- dv_reg complsb;
- dv_reg compmsb; /* 0x50 */
- dv_reg osc;
- dv_reg resv3[2];
- dv_reg scratch0; /* 0x60 */
- dv_reg scratch1;
- dv_reg scratch2;
- dv_reg kick0r;
- dv_reg kick1r; /* 0x70 */
-};
-
-#define RTC_STATE_BUSY 0x01
-#define RTC_STATE_RUN 0x02
-
-#define RTC_KICK0R_WE 0x83e70b13
-#define RTC_KICK1R_WE 0x95a4f1e0
-
-#define davinci_rtc_base ((struct davinci_rtc *)DAVINCI_RTC_BASE)
-
#endif /* __ASM_ARCH_HARDWARE_H */
#define BF_ANADIG_PFD_528_PFD0_FRAC(v) \
(((v) << 0) & BM_ANADIG_PFD_528_PFD0_FRAC)
-#define PLL2_PFD0_FREQ 352000000
-#define PLL2_PFD1_FREQ 594000000
-#define PLL2_PFD2_FREQ 396000000
-#define PLL2_PFD2_DIV_FREQ 200000000
-#define PLL3_PFD0_FREQ 720000000
-#define PLL3_PFD1_FREQ 540000000
-#define PLL3_PFD2_FREQ 508200000
-#define PLL3_PFD3_FREQ 454700000
-#define PLL3_80M 80000000
-#define PLL3_60M 60000000
-
#endif /*__ARCH_ARM_MACH_MX6_CCM_REGS_H__ */
MX6_PAD_DI0_PIN3__MMDC_MMDC_DEBUG_3 = IOMUX_PAD(0x03BC, 0x00A8, 6, 0x0000, 0, 0),
MX6_PAD_DI0_PIN3__PL301_SIM_MX6DL_PER1_HADDR_10 = IOMUX_PAD(0x03BC, 0x00A8, 7, 0x0000, 0, 0),
MX6_PAD_DI0_PIN3__LCDIF_CS = IOMUX_PAD(0x03BC, 0x00A8, 8, 0x0000, 0, 0),
- MX6_PAD_DI0_PIN4__IPU1_DI0_PIN4 = IOMUX_PAD(0x03C0, 0x00AC, 0, 0x0000, 0, PAD_CTL_DSE_120ohm),
+ MX6_PAD_DI0_PIN4__IPU1_DI0_PIN4 = IOMUX_PAD(0x03C0, 0x00AC, 0, 0x0000, 0, 0),
MX6_PAD_DI0_PIN4__LCDIF_BUSY = IOMUX_PAD(0x03C0, 0x00AC, 1, 0x08D8, 1, 0),
MX6_PAD_DI0_PIN4__AUDMUX_AUD6_RXD = IOMUX_PAD(0x03C0, 0x00AC, 2, 0x0000, 0, 0),
MX6_PAD_DI0_PIN4__USDHC1_WP = IOMUX_PAD(0x03C0, 0x00AC, 3, 0x092C, 0, 0),
{ 0x02, 0x1f, "SSP SPI #1, master, NOR" },
{ 0x03, 0x1f, "SSP SPI #2, master, NOR" },
{ 0x04, 0x1f, "NAND" },
+ { 0x06, 0x1f, "JTAG" },
{ 0x08, 0x1f, "SSP SPI #3, master, EEPROM" },
{ 0x09, 0x1f, "SSP SD/MMC #0" },
{ 0x0a, 0x1f, "SSP SD/MMC #1" },
{ 0x13, 0x1f, "SSP SPI #3, master, 1V8 NOR" },
{ 0x04, 0x1f, "NAND, 3V3" },
{ 0x14, 0x1f, "NAND, 1V8" },
+ { 0x06, 0x1f, "JTAG" },
{ 0x08, 0x1f, "SSP SPI #3, master, 3V3 EEPROM" },
{ 0x18, 0x1f, "SSP SPI #3, master, 1V8 EEPROM" },
{ 0x09, 0x1f, "SSP SD/MMC #0, 3V3" },
#define DDR_IO_2_VREF_CELLS_DDR3_VALUE 0x0
#define DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL_ES2 0x7C7C7C7C
-#define DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL_ES2 0x64656465
+#define DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL_ES2 0x64646464
#define DDR_IO_0_VREF_CELLS_DDR3_VALUE_ES2 0xBAE8C631
-#define DDR_IO_1_VREF_CELLS_DDR3_VALUE_ES2 0xB46318D8
+#define DDR_IO_1_VREF_CELLS_DDR3_VALUE_ES2 0xBC6318DC
#define DDR_IO_2_VREF_CELLS_DDR3_VALUE_ES2 0x84210000
#define EFUSE_1 0x45145100
#define BOOT_DEVICE_MMC2 6
#define BOOT_DEVICE_MMC2_2 7
#define BOOT_DEVICE_SPI 10
+#define BOOT_DEVICE_UART 0x43
#define MMC_BOOT_DEVICES_START BOOT_DEVICE_MMC1
#define MMC_BOOT_DEVICES_END BOOT_DEVICE_MMC2_2
--- /dev/null
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * Based on:
+ *
+ * -------------------------------------------------------------------------
+ *
+ * linux/include/asm-arm/arch-davinci/hardware.h
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+#ifndef __ASM_DAVINCI_RTC_H
+#define __ASM_DAVINCI_RTC_H
+
+struct davinci_rtc {
+ unsigned int second;
+ unsigned int minutes;
+ unsigned int hours;
+ unsigned int day;
+ unsigned int month; /* 0x10 */
+ unsigned int year;
+ unsigned int dotw;
+ unsigned int resv1;
+ unsigned int alarmsecond; /* 0x20 */
+ unsigned int alarmminute;
+ unsigned int alarmhour;
+ unsigned int alarmday;
+ unsigned int alarmmonth; /* 0x30 */
+ unsigned int alarmyear;
+ unsigned int resv2[2];
+ unsigned int ctrl; /* 0x40 */
+ unsigned int status;
+ unsigned int irq;
+ unsigned int complsb;
+ unsigned int compmsb; /* 0x50 */
+ unsigned int osc;
+ unsigned int resv3[2];
+ unsigned int scratch0; /* 0x60 */
+ unsigned int scratch1;
+ unsigned int scratch2;
+ unsigned int kick0r;
+ unsigned int kick1r; /* 0x70 */
+};
+
+#define RTC_STATE_BUSY 0x01
+#define RTC_STATE_RUN 0x02
+
+#define RTC_KICK0R_WE 0x83e70b13
+#define RTC_KICK1R_WE 0x95a4f1e0
+#endif
;NANDFCR = 0x00000000
[EMIF25ASYNC]
A1CR = 0x00000000
-A2CR = 0x3FFFFFFE
+A2CR = 0x04202110
A3CR = 0x00000000
A4CR = 0x00000000
NANDFCR = 0x00000012
static int green;
if (red == 0)
- red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
+ red = init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
if (red != CONFIG_IPAM390_GPIO_LED_RED)
return;
if (green == 0)
case BOOTSTAGE_ID_RUN_OS:
/*
* set normal state
- * LED Red : off
+ * LED Red : on
* LED green: off
*/
- gpio_set_value(red, LED_OFF);
+ gpio_set_value(red, LED_ON);
gpio_set_value(green, LED_OFF);
break;
case BOOTSTAGE_ID_MAIN_LOOP:
if (!bootmode)
if (ret == 0)
bootmode = 1;
- if (bootmode) {
- /*
- * Booting U-Boot
- * LED Red : on
- * LED green: off
- */
- init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
- init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
- } else {
- /*
- * Booting Linux
- * LED Red : off
- * LED green: off
- */
- init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_OFF);
- init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
- }
+ /*
+ * LED red : on
+ * LED green: off
+ */
+ init_led(CONFIG_IPAM390_GPIO_LED_RED, "red", LED_ON);
+ init_led(CONFIG_IPAM390_GPIO_LED_GREEN, "green", LED_OFF);
return bootmode;
}
#endif
}
#endif
+#ifdef CONFIG_USB_ATMEL
+void at91sam9n12ek_usb_hw_init(void)
+{
+ at91_set_pio_output(AT91_PIO_PORTB, 7, 0);
+}
+#endif
+
int board_early_init_f(void)
{
/* Enable clocks for all PIOs */
at91sam9n12ek_ks8851_hw_init();
#endif
+#ifdef CONFIG_USB_ATMEL
+ at91sam9n12ek_usb_hw_init();
+#endif
+
return 0;
}
sleep 1 ;
done
echo "erasing" ;
- sf erase 0 0x50000 ;
+ sf erase 0 0xC0000 ;
# two steps to prevent bricking
echo "programming" ;
sf write 0x12000000 $offset $filesize ;
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
-obj-$(CONFIG_LCD) += display.o
-
obj-y += cm_t35.o leds.o
#include <asm/ehci-omap.h>
#include <asm/gpio.h>
-#include "eeprom.h"
+#include "../common/eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
u32 get_board_rev(void)
{
if (!cm_t3x_rev)
- cm_t3x_rev = cm_t3x_eeprom_get_board_rev();
+ cm_t3x_rev = cl_eeprom_get_board_rev();
return cm_t3x_rev;
};
if (rc)
return 0;
- rc = cm_t3x_eeprom_read_mac_addr(enetaddr);
+ rc = cl_eeprom_read_mac_addr(enetaddr);
if (rc)
return rc;
{
return omap_ehci_hcd_stop();
}
-
#endif /* CONFIG_USB_EHCI_OMAP */
--- /dev/null
+#
+# (C) Copyright 2011 - 2013 CompuLab, Ltd. <www.compulab.co.il>
+#
+# Author: Igor Grinberg <grinberg@compulab.co.il>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_DRIVER_OMAP34XX_I2C) += eeprom.o
+obj-$(CONFIG_LCD) += omap3_display.o
#define LAYOUT_INVALID 0
#define LAYOUT_LEGACY 0xff
-static int eeprom_layout; /* Implicitly LAYOUT_INVALID */
+static int cl_eeprom_layout; /* Implicitly LAYOUT_INVALID */
-static int cm_t3x_eeprom_read(uint offset, uchar *buf, int len)
+static int cl_eeprom_read(uint offset, uchar *buf, int len)
{
return i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, buf, len);
}
-static int eeprom_setup_layout(void)
+static int cl_eeprom_setup_layout(void)
{
int res;
- if (eeprom_layout != LAYOUT_INVALID)
+ if (cl_eeprom_layout != LAYOUT_INVALID)
return 0;
- res = cm_t3x_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
- (uchar *)&eeprom_layout, 1);
+ res = cl_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
+ (uchar *)&cl_eeprom_layout, 1);
if (res) {
- eeprom_layout = LAYOUT_INVALID;
+ cl_eeprom_layout = LAYOUT_INVALID;
return res;
}
- if (eeprom_layout == 0 || eeprom_layout >= 0x20)
- eeprom_layout = LAYOUT_LEGACY;
+ if (cl_eeprom_layout == 0 || cl_eeprom_layout >= 0x20)
+ cl_eeprom_layout = LAYOUT_LEGACY;
return 0;
}
uint offset;
memset(serialnr, 0, sizeof(*serialnr));
- if (eeprom_setup_layout())
+
+ if (cl_eeprom_setup_layout())
return;
- offset = (eeprom_layout != LAYOUT_LEGACY) ?
- BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
- if (cm_t3x_eeprom_read(offset, (uchar *)serial, 8))
+ offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
+ BOARD_SERIAL_OFFSET : BOARD_SERIAL_OFFSET_LEGACY;
+
+ if (cl_eeprom_read(offset, (uchar *)serial, 8))
return;
if (serial[0] != 0xffffffff && serial[1] != 0xffffffff) {
}
/*
- * Routine: cm_t3x_eeprom_read_mac_addr
+ * Routine: cl_eeprom_read_mac_addr
* Description: read mac address and store it in buf.
*/
-int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+int cl_eeprom_read_mac_addr(uchar *buf)
{
uint offset;
- if (eeprom_setup_layout())
+ if (cl_eeprom_setup_layout())
return 0;
- offset = (eeprom_layout != LAYOUT_LEGACY) ?
+ offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
MAC_ADDR_OFFSET : MAC_ADDR_OFFSET_LEGACY;
- return cm_t3x_eeprom_read(offset, buf, 6);
+
+ return cl_eeprom_read(offset, buf, 6);
}
/*
- * Routine: cm_t3x_eeprom_get_board_rev
+ * Routine: cl_eeprom_get_board_rev
* Description: read system revision from eeprom
*/
-u32 cm_t3x_eeprom_get_board_rev(void)
+u32 cl_eeprom_get_board_rev(void)
{
u32 rev = 0;
char str[5]; /* Legacy representation can contain at most 4 digits */
uint offset = BOARD_REV_OFFSET_LEGACY;
- if (eeprom_setup_layout())
+ if (cl_eeprom_setup_layout())
return 0;
- if (eeprom_layout != LAYOUT_LEGACY)
+ if (cl_eeprom_layout != LAYOUT_LEGACY)
offset = BOARD_REV_OFFSET;
- if (cm_t3x_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
+ if (cl_eeprom_read(offset, (uchar *)&rev, BOARD_REV_SIZE))
return 0;
/*
* Convert legacy syntactic representation to semantic
* representation. i.e. for rev 1.00: 0x100 --> 0x64
*/
- if (eeprom_layout == LAYOUT_LEGACY) {
+ if (cl_eeprom_layout == LAYOUT_LEGACY) {
sprintf(str, "%x", rev);
rev = simple_strtoul(str, NULL, 10);
}
#define _EEPROM_
#ifdef CONFIG_DRIVER_OMAP34XX_I2C
-int cm_t3x_eeprom_read_mac_addr(uchar *buf);
-u32 cm_t3x_eeprom_get_board_rev(void);
+int cl_eeprom_read_mac_addr(uchar *buf);
+u32 cl_eeprom_get_board_rev(void);
#else
-static inline int cm_t3x_eeprom_read_mac_addr(uchar *buf)
+static inline int cl_eeprom_read_mac_addr(uchar *buf)
{
return 1;
}
-static inline u32 cm_t3x_eeprom_get_board_rev(void)
+static inline u32 cl_eeprom_get_board_rev(void)
{
return 0;
}
.lcd_size = PANEL_LCD_SIZE(640, 480),
.timing_h = DSS_HBP(48) | DSS_HFP(16) | DSS_HSW(96),
.timing_v = DSS_VBP(33) | DSS_VFP(10) | DSS_VSW(2),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
.divisor = 12 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
.lcd_size = PANEL_LCD_SIZE(800, 600),
.timing_h = DSS_HBP(88) | DSS_HFP(40) | DSS_HSW(128),
.timing_v = DSS_VBP(23) | DSS_VFP(1) | DSS_VSW(4),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
.divisor = 8 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
.lcd_size = PANEL_LCD_SIZE(1024, 768),
.timing_h = DSS_HBP(160) | DSS_HFP(24) | DSS_HSW(136),
.timing_v = DSS_VBP(29) | DSS_VFP(3) | DSS_VSW(6),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
.divisor = 5 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
.lcd_size = PANEL_LCD_SIZE(1152, 864),
.timing_h = DSS_HBP(256) | DSS_HFP(64) | DSS_HSW(128),
.timing_v = DSS_VBP(32) | DSS_VFP(1) | DSS_VSW(3),
- .divisor = 3 | (1 << 16),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
+ .divisor = 4 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
.load_mode = 2,
.lcd_size = PANEL_LCD_SIZE(1280, 960),
.timing_h = DSS_HBP(312) | DSS_HFP(96) | DSS_HSW(112),
.timing_v = DSS_VBP(36) | DSS_VFP(1) | DSS_VSW(3),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
.divisor = 3 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
.lcd_size = PANEL_LCD_SIZE(1280, 1024),
.timing_h = DSS_HBP(248) | DSS_HFP(48) | DSS_HSW(112),
.timing_v = DSS_VBP(38) | DSS_VFP(1) | DSS_VSW(3),
+ .pol_freq = DSS_IHS | DSS_IVS | DSS_IPC,
.divisor = 3 | (1 << 16),
.data_lines = LCD_INTERFACE_24_BIT,
.panel_type = ACTIVE_DISPLAY,
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y := tricorder.o
+obj-y := tricorder.o tricorder-eeprom.o led.o
--- /dev/null
+/*
+ * Copyright (c) 2013 Corscience GmbH & Co.KG
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <status_led.h>
+#include <twl4030.h>
+#include <asm/arch/cpu.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+
+#define TRICORDER_STATUS_LED_YELLOW 42
+#define TRICORDER_STATUS_LED_GREEN 43
+
+void __led_init(led_id_t mask, int state)
+{
+ __led_set(mask, state);
+}
+
+void __led_toggle(led_id_t mask)
+{
+ int toggle_gpio = 0;
+#ifdef STATUS_LED_BIT
+ if (!toggle_gpio && STATUS_LED_BIT & mask)
+ toggle_gpio = TRICORDER_STATUS_LED_GREEN;
+#endif
+#ifdef STATUS_LED_BIT1
+ if (!toggle_gpio && STATUS_LED_BIT1 & mask)
+ toggle_gpio = TRICORDER_STATUS_LED_YELLOW;
+#endif
+#ifdef STATUS_LED_BIT2
+ if (!toggle_gpio && STATUS_LED_BIT2 & mask) {
+ uint8_t val;
+ twl4030_i2c_read_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+ &val);
+ val ^= (TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDAPWM);
+ twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+ val);
+ }
+#endif
+ if (toggle_gpio) {
+ int state;
+ gpio_request(toggle_gpio, "");
+ state = gpio_get_value(toggle_gpio);
+ gpio_set_value(toggle_gpio, !state);
+ }
+}
+
+void __led_set(led_id_t mask, int state)
+{
+#ifdef STATUS_LED_BIT
+ if (STATUS_LED_BIT & mask) {
+ gpio_request(TRICORDER_STATUS_LED_GREEN, "");
+ gpio_direction_output(TRICORDER_STATUS_LED_GREEN, 0);
+ gpio_set_value(TRICORDER_STATUS_LED_GREEN, state);
+ }
+#endif
+#ifdef STATUS_LED_BIT1
+ if (STATUS_LED_BIT1 & mask) {
+ gpio_request(TRICORDER_STATUS_LED_YELLOW, "");
+ gpio_direction_output(TRICORDER_STATUS_LED_YELLOW, 0);
+ gpio_set_value(TRICORDER_STATUS_LED_YELLOW, state);
+ }
+#endif
+#ifdef STATUS_LED_BIT2
+ if (STATUS_LED_BIT2 & mask) {
+ if (STATUS_LED_OFF == state)
+ twl4030_i2c_write_u8(TWL4030_CHIP_LED,
+ TWL4030_LED_LEDEN, 0);
+ else
+ twl4030_i2c_write_u8(TWL4030_CHIP_LED,
+ TWL4030_LED_LEDEN,
+ (TWL4030_LED_LEDEN_LEDAON |
+ TWL4030_LED_LEDEN_LEDAPWM));
+ }
+#endif
+}
--- /dev/null
+/*
+ * (C) Copyright 2013
+ * Corscience GmbH & Co. KG, <www.corscience.de>
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <i2c.h>
+
+#include "tricorder-eeprom.h"
+
+static inline void warn_wrong_value(const char *msg, unsigned int a,
+ unsigned int b)
+{
+ printf("Expected EEPROM %s %08x, got %08x\n", msg, a, b);
+}
+
+static int handle_eeprom_v0(struct tricorder_eeprom *eeprom)
+{
+ struct tricorder_eeprom_v0 {
+ uint32_t magic;
+ uint16_t length;
+ uint16_t version;
+ char board_name[TRICORDER_BOARD_NAME_LENGTH];
+ char board_version[TRICORDER_BOARD_VERSION_LENGTH];
+ char board_serial[TRICORDER_BOARD_SERIAL_LENGTH];
+ uint32_t crc32;
+ } __packed eepromv0;
+ uint32_t crc;
+
+ printf("Old EEPROM (v0), consider rewrite!\n");
+
+ if (be16_to_cpu(eeprom->length) != sizeof(eepromv0)) {
+ warn_wrong_value("length", sizeof(eepromv0),
+ be16_to_cpu(eeprom->length));
+ return 1;
+ }
+
+ memcpy(&eepromv0, eeprom, sizeof(eepromv0));
+
+ crc = crc32(0L, (unsigned char *)&eepromv0,
+ sizeof(eepromv0) - sizeof(eepromv0.crc32));
+ if (be32_to_cpu(eepromv0.crc32) != crc) {
+ warn_wrong_value("CRC", be32_to_cpu(eepromv0.crc32),
+ crc);
+ return 1;
+ }
+
+ /* Ok the content is correct, do the conversion */
+ memset(eeprom->interface_version, 0x0,
+ TRICORDER_INTERFACE_VERSION_LENGTH);
+ crc = crc32(0L, (unsigned char *)eeprom, TRICORDER_EEPROM_CRC_SIZE);
+ eeprom->crc32 = cpu_to_be32(crc);
+
+ return 0;
+}
+
+static int handle_eeprom_v1(struct tricorder_eeprom *eeprom)
+{
+ uint32_t crc;
+
+ if (be16_to_cpu(eeprom->length) != TRICORDER_EEPROM_SIZE) {
+ warn_wrong_value("length", TRICORDER_EEPROM_SIZE,
+ be16_to_cpu(eeprom->length));
+ return 1;
+ }
+
+ crc = crc32(0L, (unsigned char *)eeprom, TRICORDER_EEPROM_CRC_SIZE);
+ if (be32_to_cpu(eeprom->crc32) != crc) {
+ warn_wrong_value("CRC", be32_to_cpu(eeprom->crc32), crc);
+ return 1;
+ }
+
+ return 0;
+}
+
+int tricorder_get_eeprom(int addr, struct tricorder_eeprom *eeprom)
+{
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+ unsigned int bus = i2c_get_bus_num();
+ i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+ memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
+
+ i2c_read(addr, 0, 2, (unsigned char *)eeprom, TRICORDER_EEPROM_SIZE);
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+ i2c_set_bus_num(bus);
+#endif
+
+ if (be32_to_cpu(eeprom->magic) != TRICORDER_EEPROM_MAGIC) {
+ warn_wrong_value("magic", TRICORDER_EEPROM_MAGIC,
+ be32_to_cpu(eeprom->magic));
+ return 1;
+ }
+
+ switch (be16_to_cpu(eeprom->version)) {
+ case 0:
+ return handle_eeprom_v0(eeprom);
+ case 1:
+ return handle_eeprom_v1(eeprom);
+ default:
+ warn_wrong_value("version", TRICORDER_EEPROM_VERSION,
+ be16_to_cpu(eeprom->version));
+ return 1;
+ }
+}
+
+#if !defined(CONFIG_SPL)
+int tricorder_eeprom_read(unsigned devaddr)
+{
+ struct tricorder_eeprom eeprom;
+ int ret = tricorder_get_eeprom(devaddr, &eeprom);
+
+ if (ret)
+ return ret;
+
+ printf("Board type: %.*s\n",
+ sizeof(eeprom.board_name), eeprom.board_name);
+ printf("Board version: %.*s\n",
+ sizeof(eeprom.board_version), eeprom.board_version);
+ printf("Board serial: %.*s\n",
+ sizeof(eeprom.board_serial), eeprom.board_serial);
+ printf("Board interface version: %.*s\n",
+ sizeof(eeprom.interface_version),
+ eeprom.interface_version);
+
+ return ret;
+}
+
+int tricorder_eeprom_write(unsigned devaddr, const char *name,
+ const char *version, const char *serial, const char *interface)
+{
+ struct tricorder_eeprom eeprom, eeprom_verify;
+ size_t length;
+ uint32_t crc;
+ int ret;
+ unsigned char *p;
+ int i;
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+ unsigned int bus;
+#endif
+
+ memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
+ memset(eeprom_verify, 0, TRICORDER_EEPROM_SIZE);
+
+ eeprom.magic = cpu_to_be32(TRICORDER_EEPROM_MAGIC);
+ eeprom.length = cpu_to_be16(TRICORDER_EEPROM_SIZE);
+ eeprom.version = cpu_to_be16(TRICORDER_EEPROM_VERSION);
+
+ length = min(sizeof(eeprom.board_name), strlen(name));
+ strncpy(eeprom.board_name, name, length);
+
+ length = min(sizeof(eeprom.board_version), strlen(version));
+ strncpy(eeprom.board_version, version, length);
+
+ length = min(sizeof(eeprom.board_serial), strlen(serial));
+ strncpy(eeprom.board_serial, serial, length);
+
+ if (interface) {
+ length = min(sizeof(eeprom.interface_version),
+ strlen(interface));
+ strncpy(eeprom.interface_version, interface, length);
+ }
+
+ crc = crc32(0L, (unsigned char *)&eeprom, TRICORDER_EEPROM_CRC_SIZE);
+ eeprom.crc32 = cpu_to_be32(crc);
+
+#if defined(DEBUG)
+ puts("Tricorder EEPROM content:\n");
+ print_buffer(0, &eeprom, 1, sizeof(eeprom), 16);
+#endif
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+ bus = i2c_get_bus_num();
+ i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM);
+#endif
+
+ /* do page write to the eeprom */
+ for (i = 0, p = (unsigned char *)&eeprom;
+ i < sizeof(eeprom);
+ i += 32, p += 32) {
+ ret = i2c_write(devaddr, i, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
+ p, min(sizeof(eeprom) - i, 32));
+ if (ret)
+ break;
+ udelay(5000); /* 5ms write cycle timing */
+ }
+
+ ret = i2c_read(devaddr, 0, 2, (unsigned char *)&eeprom_verify,
+ TRICORDER_EEPROM_SIZE);
+
+ if (memcmp(&eeprom, &eeprom_verify, sizeof(eeprom)) != 0) {
+ printf("Tricorder: Could not verify EEPROM content!\n");
+ ret = 1;
+ }
+
+#ifdef CONFIG_SYS_EEPROM_BUS_NUM
+ i2c_set_bus_num(bus);
+#endif
+ return ret;
+}
+
+int do_tricorder_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ if (argc == 3) {
+ ulong dev_addr = simple_strtoul(argv[2], NULL, 16);
+ eeprom_init();
+ if (strcmp(argv[1], "read") == 0) {
+ int rcode;
+
+ rcode = tricorder_eeprom_read(dev_addr);
+
+ return rcode;
+ }
+ } else if (argc == 6 || argc == 7) {
+ ulong dev_addr = simple_strtoul(argv[2], NULL, 16);
+ char *name = argv[3];
+ char *version = argv[4];
+ char *serial = argv[5];
+ char *interface = NULL;
+ eeprom_init();
+
+ if (argc == 7)
+ interface = argv[6];
+
+ if (strcmp(argv[1], "write") == 0) {
+ int rcode;
+
+ rcode = tricorder_eeprom_write(dev_addr, name, version,
+ serial, interface);
+
+ return rcode;
+ }
+ }
+
+ return CMD_RET_USAGE;
+}
+
+U_BOOT_CMD(
+ tricordereeprom, 7, 1, do_tricorder_eeprom,
+ "Tricorder EEPROM",
+ "read devaddr\n"
+ " - read Tricorder EEPROM at devaddr and print content\n"
+ "tricordereeprom write devaddr name version serial [interface]\n"
+ " - write Tricorder EEPROM at devaddr with 'name', 'version'"
+ "and 'serial'\n"
+ " optional add an HW interface parameter"
+);
+#endif /* CONFIG_SPL */
--- /dev/null
+/*
+ * (C) Copyright 2013
+ * Corscience GmbH & Co. KG, <www.corscience.de>
+ * Andreas Bießmann <andreas.biessmann@corscience.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef TRICORDER_EEPROM_H_
+#define TRICORDER_EEPROM_H_
+
+#include <linux/compiler.h>
+
+#define TRICORDER_EEPROM_MAGIC 0xc2a94f52
+#define TRICORDER_EEPROM_VERSION 1
+
+#define TRICORDER_BOARD_NAME_LENGTH 12
+#define TRICORDER_BOARD_VERSION_LENGTH 4
+#define TRICORDER_BOARD_SERIAL_LENGTH 12
+#define TRICORDER_INTERFACE_VERSION_LENGTH 4
+
+struct tricorder_eeprom {
+ uint32_t magic;
+ uint16_t length;
+ uint16_t version;
+ char board_name[TRICORDER_BOARD_NAME_LENGTH];
+ char board_version[TRICORDER_BOARD_VERSION_LENGTH];
+ char board_serial[TRICORDER_BOARD_SERIAL_LENGTH];
+ char interface_version[TRICORDER_INTERFACE_VERSION_LENGTH];
+ uint32_t crc32;
+} __packed;
+
+#define TRICORDER_EEPROM_SIZE sizeof(struct tricorder_eeprom)
+#define TRICORDER_EEPROM_CRC_SIZE (TRICORDER_EEPROM_SIZE - \
+ sizeof(uint32_t))
+
+/**
+ * @brief read eeprom information from a specific eeprom address
+ */
+int tricorder_get_eeprom(int addr, struct tricorder_eeprom *eeprom);
+
+#endif /* TRICORDER_EEPROM_H_ */
#include <common.h>
#include <twl4030.h>
#include <asm/io.h>
+#include <asm/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include "tricorder.h"
+#include "tricorder-eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
return 0;
}
+/**
+ * get_eeprom - read the eeprom
+ *
+ * @eeprom - pointer to a eeprom struct to fill
+ *
+ * This function will panic() on wrong EEPROM content
+ */
+static void get_eeprom(struct tricorder_eeprom *eeprom)
+{
+ int ret;
+
+ if (!eeprom)
+ panic("No eeprom given!\n");
+
+ ret = gpio_request(7, "BMS");
+ if (ret)
+ panic("gpio: requesting BMS pin failed\n");
+
+ ret = gpio_direction_input(7);
+ if (ret)
+ panic("gpio: set BMS as input failed\n");
+
+ ret = gpio_get_value(7);
+ if (ret < 0)
+ panic("gpio: get BMS pin state failed\n");
+
+ gpio_free(7);
+
+ if (ret == 0) {
+ /* BMS is _not_ set, do the EEPROM check */
+ ret = tricorder_get_eeprom(0x51, eeprom);
+ if (!ret) {
+ if (strncmp(eeprom->board_name, "CS10411", 7) != 0)
+ panic("Wrong board name '%.*s'\n",
+ sizeof(eeprom->board_name),
+ eeprom->board_name);
+ if (eeprom->board_version[0] < 'D')
+ panic("Wrong board version '%.*s'\n",
+ sizeof(eeprom->board_version),
+ eeprom->board_version);
+ } else {
+ panic("Could not get board revision\n");
+ }
+ }
+}
+
+/**
+ * print_hwversion - print out a HW version string
+ *
+ * @eeprom - pointer to the eeprom
+ */
+static void print_hwversion(struct tricorder_eeprom *eeprom)
+{
+ size_t len;
+ if (!eeprom)
+ panic("No eeprom given!");
+
+ printf("Board %.*s:%.*s serial %.*s",
+ sizeof(eeprom->board_name), eeprom->board_name,
+ sizeof(eeprom->board_version), eeprom->board_version,
+ sizeof(eeprom->board_serial), eeprom->board_serial);
+
+ len = strnlen(eeprom->interface_version,
+ sizeof(eeprom->interface_version));
+ if (len > 0)
+ printf(" HW interface version %.*s",
+ sizeof(eeprom->interface_version),
+ eeprom->interface_version);
+ puts("\n");
+}
+
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
+ struct tricorder_eeprom eeprom;
+ get_eeprom(&eeprom);
+ print_hwversion(&eeprom);
+
twl4030_power_init();
-#ifdef CONFIG_TWL4030_LED
- twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
-#endif
+ status_led_set(0, STATUS_LED_ON);
+ status_led_set(1, STATUS_LED_ON);
+ status_led_set(2, STATUS_LED_ON);
dieid_num_r();
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
+ struct tricorder_eeprom eeprom;
+ get_eeprom(&eeprom);
+
/* General SDRC config */
- timings->mcfg = MICRON_V_MCFG_165(128 << 20);
- timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ if (eeprom.board_version[0] > 'D') {
+ /* use optimized timings for our SDRAM device */
+ timings->mcfg = MCFG((256 << 20), 14);
+#define MT46H64M32_TDAL 6 /* Twr/Tck + Trp/tck */
+ /* 15/6 + 18/6 = 5.5 -> 6 */
+#define MT46H64M32_TDPL 3 /* 15/6 = 2.5 -> 3 (Twr) */
+#define MT46H64M32_TRRD 2 /* 12/6 = 2 */
+#define MT46H64M32_TRCD 3 /* 18/6 = 3 */
+#define MT46H64M32_TRP 3 /* 18/6 = 3 */
+#define MT46H64M32_TRAS 7 /* 42/6 = 7 */
+#define MT46H64M32_TRC 10 /* 60/6 = 10 */
+#define MT46H64M32_TRFC 12 /* 72/6 = 12 */
+ timings->ctrla = ACTIM_CTRLA(MT46H64M32_TRFC, MT46H64M32_TRC,
+ MT46H64M32_TRAS, MT46H64M32_TRP,
+ MT46H64M32_TRCD, MT46H64M32_TRRD,
+ MT46H64M32_TDPL,
+ MT46H64M32_TDAL);
+
+#define MT46H64M32_TWTR 1
+#define MT46H64M32_TCKE 1
+#define MT46H64M32_XSR 19 /* 112.5/6 = 18.75 => ~19 */
+#define MT46H64M32_TXP 1
+ timings->ctrlb = ACTIM_CTRLB(MT46H64M32_TWTR, MT46H64M32_TCKE,
+ MT46H64M32_TXP, MT46H64M32_XSR);
- /* AC timings */
- timings->ctrla = MICRON_V_ACTIMA_165;
- timings->ctrlb = MICRON_V_ACTIMB_165;
- timings->mr = MICRON_V_MR_165;
+ timings->mr = MICRON_V_MR_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ } else {
+ /* use conservative beagleboard timings as default */
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->mr = MICRON_V_MR_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ }
}
MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
- MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
- MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M4)) /*GPIO 42*/\
+ MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M4)) /*GPIO 43*/\
MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
#include <asm/arch/hardware.h>
#include <asm/arch/sdmmc_defs.h>
#include <asm/arch/timer_defs.h>
+#include <asm/davinci_rtc.h>
DECLARE_GLOBAL_DATA_PTR;
#
-# (C) Copyright 2006
+# (C) Copyright 2000-2006
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y := flash.o pdnb3.o nand.o
+ifndef CONFIG_SPL_BUILD
+obj-y := bg0900.o
+else
+obj-y := spl_boot.o
+endif
--- /dev/null
+/*
+ * PPC-AG BG0900 board
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+ /* IO0 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK0, 480000);
+ /* IO1 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK1, 480000);
+
+ /* SSP2 clock at 160MHz */
+ mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return mxs_dram_init();
+}
+
+int board_init(void)
+{
+ /* Adress of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_NET
+int board_eth_init(bd_t *bis)
+{
+ struct mxs_clkctrl_regs *clkctrl_regs =
+ (struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
+ struct eth_device *dev;
+ int ret;
+
+ ret = cpu_eth_init(bis);
+
+ /* BG0900 uses ENET_CLK PAD to drive FEC clock */
+ writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+ &clkctrl_regs->hw_clkctrl_enet);
+
+ /* Reset FEC PHYs */
+ gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+ udelay(200);
+ gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+ ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+ if (ret) {
+ puts("FEC MXS: Unable to init FEC0\n");
+ return ret;
+ }
+
+ dev = eth_get_dev_by_name("FEC0");
+ if (!dev) {
+ puts("FEC MXS: Unable to get FEC0 device entry\n");
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+#endif
--- /dev/null
+/*
+ * PPC-AG BG0900 Boot setup
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define MUX_CONFIG_GPMI (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_ENET (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_EMI (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_SSP2 (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+
+const iomux_cfg_t iomux_setup[] = {
+ /* DUART */
+ MX28_PAD_PWM0__DUART_RX,
+ MX28_PAD_PWM1__DUART_TX,
+
+ /* GPMI NAND */
+ MX28_PAD_GPMI_D00__GPMI_D0 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D01__GPMI_D1 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D02__GPMI_D2 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D03__GPMI_D3 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D04__GPMI_D4 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D05__GPMI_D5 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D06__GPMI_D6 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_D07__GPMI_D7 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_CE0N__GPMI_CE0N | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_RDY0__GPMI_READY0 | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_RDN__GPMI_RDN |
+ (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_WRN__GPMI_WRN | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_ALE__GPMI_ALE | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_CLE__GPMI_CLE | MUX_CONFIG_GPMI,
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN | MUX_CONFIG_GPMI,
+
+ /* FEC0 */
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+
+ /* FEC0 Reset */
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+ /* EMI */
+ MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+ MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+ /* SPI2 (for SPI flash) */
+ MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
+ MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
+ MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
+ MX28_PAD_SSP2_SS0__SSP2_D3 |
+ (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
+};
+
+void mxs_adjust_memory_params(uint32_t *dram_vals)
+{
+ /*
+ * DDR Controller Registers
+ * Manufacturer: Winbond
+ * Device Part Number: W972GG6JB-25I
+ * Clock Freq.: 200MHz
+ * Density: 2Gb
+ * Chip Selects: 1
+ * Number of Banks: 8
+ * Row address: 14
+ * Column address: 10
+ */
+
+ dram_vals[0x74 / 4] = 0x0102010A;
+ dram_vals[0x98 / 4] = 0x04005003;
+ dram_vals[0x9c / 4] = 0x090000c8;
+
+ dram_vals[0xa8 / 4] = 0x0036b009;
+ dram_vals[0xac / 4] = 0x03270612;
+
+ dram_vals[0xb0 / 4] = 0x02020202;
+ dram_vals[0xb4 / 4] = 0x00c80029;
+
+ dram_vals[0xc0 / 4] = 0x00011900;
+
+ dram_vals[0x12c / 4] = 0x07400300;
+ dram_vals[0x130 / 4] = 0x07400300;
+ dram_vals[0x2c4 / 4] = 0x02030303;
+}
+
+void board_init_ll(const uint32_t arg, const uint32_t *resptr)
+{
+ mxs_common_spl_init(arg, resptr, iomux_setup, ARRAY_SIZE(iomux_setup));
+}
+++ /dev/null
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/ixp425.h>
-
-#if !defined(CONFIG_FLASH_CFI_DRIVER)
-
-/*
- * include common flash code (for esd boards)
- */
-#include "../common/flash.c"
-
-/*
- * Prototypes
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-
-static inline ulong ld(ulong x)
-{
- ulong k = 0;
-
- while (x >>= 1)
- ++k;
-
- return k;
-}
-
-unsigned long flash_init(void)
-{
- unsigned long size;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; i++)
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- size = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN)
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size, size<<20);
-
- /* Reconfigure CS0 to actual FLASH size */
- *IXP425_EXP_CS0 = (*IXP425_EXP_CS0 & ~0x00003C00) | ((ld(size) - 9) << 10);
-
- /* Monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- /* Environment protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- /* Redundant environment protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR_REDUND,
- CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]);
-
- flash_info[0].size = size;
-
- return size;
-}
-
-#endif /* CONFIG_FLASH_CFI_DRIVER */
+++ /dev/null
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-
-struct pdnb3_ndfc_regs {
- uchar cmd;
- uchar wait;
- uchar addr;
- uchar term;
- uchar data;
-};
-
-static u8 hwctl;
-static struct pdnb3_ndfc_regs *pdnb3_ndfc;
-
-#define readb(addr) *(volatile u_char *)(addr)
-#define readl(addr) *(volatile u_long *)(addr)
-#define writeb(d,addr) *(volatile u_char *)(addr) = (d)
-
-/*
- * The PDNB3 has a NAND Flash Controller (NDFC) that handles all accesses to
- * the NAND devices. The NDFC has command, address and data registers that
- * when accessed will set up the NAND flash pins appropriately. We'll use the
- * hwcontrol function to save the configuration in a global variable.
- * We can then use this information in the read and write functions to
- * determine which NDFC register to access.
- *
- * There is one NAND devices on the board, a Hynix HY27US08561A (32 MByte).
- */
-static void pdnb3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
-
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- hwctl |= 0x1;
- else
- hwctl &= ~0x1;
- if ( ctrl & NAND_ALE )
- hwctl |= 0x2;
- else
- hwctl &= ~0x2;
- if ( (ctrl & NAND_NCE) != NAND_NCE)
- writeb(0x00, &(pdnb3_ndfc->term));
- }
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-
-static u_char pdnb3_nand_read_byte(struct mtd_info *mtd)
-{
- return readb(&(pdnb3_ndfc->data));
-}
-
-static void pdnb3_nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
- int i;
-
- for (i = 0; i < len; i++) {
- if (hwctl & 0x1)
- writeb(buf[i], &(pdnb3_ndfc->cmd));
- else if (hwctl & 0x2)
- writeb(buf[i], &(pdnb3_ndfc->addr));
- else
- writeb(buf[i], &(pdnb3_ndfc->data));
- }
-}
-
-static void pdnb3_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
- int i;
-
- for (i = 0; i < len; i++)
- buf[i] = readb(&(pdnb3_ndfc->data));
-}
-
-static int pdnb3_nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
- int i;
-
- for (i = 0; i < len; i++)
- if (buf[i] != readb(&(pdnb3_ndfc->data)))
- return i;
-
- return 0;
-}
-
-static int pdnb3_nand_dev_ready(struct mtd_info *mtd)
-{
- /*
- * Blocking read to wait for NAND to be ready
- */
- readb(&(pdnb3_ndfc->wait));
-
- /*
- * Return always true
- */
- return 1;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- pdnb3_ndfc = (struct pdnb3_ndfc_regs *)CONFIG_SYS_NAND_BASE;
-
- nand->ecc.mode = NAND_ECC_SOFT;
-
- /* Set address of NAND IO lines (Using Linear Data Access Region) */
- nand->IO_ADDR_R = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4);
- nand->IO_ADDR_W = (void __iomem *) ((ulong) pdnb3_ndfc + 0x4);
- /* Reference hardware control function */
- nand->cmd_ctrl = pdnb3_nand_hwcontrol;
- nand->read_byte = pdnb3_nand_read_byte;
- nand->write_buf = pdnb3_nand_write_buf;
- nand->read_buf = pdnb3_nand_read_buf;
- nand->verify_buf = pdnb3_nand_verify_buf;
- nand->dev_ready = pdnb3_nand_dev_ready;
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* predefine these here for FPGA programming (before including fpga.c) */
-#define SET_FPGA(data) *IXP425_GPIO_GPOUTR = (data)
-#define FPGA_DONE_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_DONE)
-#define FPGA_INIT_STATE (*IXP425_GPIO_GPINR & CONFIG_SYS_FPGA_INIT)
-#define OLD_VAL old_val
-
-static unsigned long old_val = 0;
-
-/*
- * include common fpga code (for prodrive boards)
- */
-#include "../common/fpga.c"
-
-/*
- * Miscelaneous platform dependent initialisations
- */
-int board_init(void)
-{
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x00000100;
-
- GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_FPGA_RESET);
-
- GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_SYS_RUNNING);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_SYS_RUNNING);
-
- /*
- * Setup GPIO's for FPGA programming
- */
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG);
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK);
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PRG);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK);
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DATA);
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_INIT);
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DONE);
-
- /*
- * Setup GPIO's for interrupts
- */
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA);
- GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA);
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB);
- GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB);
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTORE_INT);
- GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTORE_INT);
- GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RESTART_INT);
- GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RESTART_INT);
-
- /*
- * Setup GPIO's for 33MHz clock output
- */
- *IXP425_GPIO_GPCLKR = 0x01FF0000;
- GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_CLK_33M);
-
- /*
- * Setup other chip select's
- */
- *IXP425_EXP_CS1 = CONFIG_SYS_EXP_CS1;
-
- return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- puts("Board: PDNB3");
-
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return (0);
-}
-
-int dram_init(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return (0);
-}
-
-int do_fpga_boot(unsigned char *fpgadata)
-{
- unsigned char *dst;
- int status;
- int index;
- int i;
- ulong len = CONFIG_SYS_MALLOC_LEN;
-
- /*
- * Setup GPIO's for FPGA programming
- */
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PRG);
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_CLK);
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DATA);
-
- /*
- * Save value so no readback is required upon programming
- */
- old_val = *IXP425_GPIO_GPOUTR;
-
- /*
- * First try to decompress fpga image (gzip compressed?)
- */
- dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
- if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
- printf("Error: Image has to be gzipp'ed!\n");
- return -1;
- }
-
- status = fpga_boot(dst, len);
- if (status != 0) {
- printf("\nFPGA: Booting failed ");
- switch (status) {
- case ERROR_FPGA_PRG_INIT_LOW:
- printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
- break;
- case ERROR_FPGA_PRG_INIT_HIGH:
- printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
- break;
- case ERROR_FPGA_PRG_DONE:
- printf("(Timeout: DONE not high after programming FPGA)\n ");
- break;
- }
-
- /* display infos on fpgaimage */
- index = 15;
- for (i=0; i<4; i++) {
- len = dst[index];
- printf("FPGA: %s\n", &(dst[index+1]));
- index += len+3;
- }
- putc ('\n');
- /* delayed reboot */
- for (i=5; i>0; i--) {
- printf("Rebooting in %2d seconds \r",i);
- for (index=0;index<1000;index++)
- udelay(1000);
- }
- putc('\n');
- do_reset(NULL, 0, 0, NULL);
- }
-
- puts("FPGA: ");
-
- /* display infos on fpgaimage */
- index = 15;
- for (i=0; i<4; i++) {
- len = dst[index];
- printf("%s ", &(dst[index+1]));
- index += len+3;
- }
- putc('\n');
-
- free(dst);
-
- /*
- * Reset FPGA
- */
- GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_FPGA_RESET);
- udelay(10);
- GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_FPGA_RESET);
-
- return (0);
-}
-
-int do_fpga(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- ulong addr;
-
- if (argc < 2)
- return cmd_usage(cmdtp);
-
- addr = simple_strtoul(argv[1], NULL, 16);
-
- return do_fpga_boot((unsigned char *)addr);
-}
-
-U_BOOT_CMD(
- fpga, 2, 0, do_fpga,
- "boot FPGA",
- "address size\n - boot FPGA with gzipped image at <address>"
-);
-
-#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
-extern struct pci_controller hose;
-extern void pci_ixp_init(struct pci_controller * hose);
-
-void pci_init_board(void)
-{
- extern void pci_ixp_init (struct pci_controller *hose);
-
- pci_ixp_init(&hose);
-}
-#endif
#include <cpsw.h>
#include <power/tps65217.h>
#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
#include "board.h"
DECLARE_GLOBAL_DATA_PTR;
STNOR_GPMC_CONFIG5, STNOR_GPMC_CONFIG6, STNOR_GPMC_CONFIG7 };
#endif
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
+#endif
+
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
gpmc_init();
--- /dev/null
+#
+# (C) Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := udoo.o
--- /dev/null
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define WDT_EN IMX_GPIO_NR(5, 4)
+#define WDT_TRG IMX_GPIO_NR(3, 19)
+
+int dram_init(void)
+{
+ gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+ MX6_PAD_EIM_A24__GPIO_5_4 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_D19__GPIO_3_19,
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+static void setup_iomux_wdog(void)
+{
+ imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+ gpio_direction_output(WDT_TRG, 0);
+ gpio_direction_output(WDT_EN, 1);
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg = { USDHC3_BASE_ADDR };
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1; /* Always present */
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg.max_bus_width = 4;
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_wdog();
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Udoo\n");
+
+ return 0;
+}
This file contains information for the port of U-Boot to the Wandboard.
-Wandboard is a development board that has two variants: one version based
-on mx6 dual lite and another one based on mx6 solo.
+Wandboard is a development board that has three variants based on the following
+SoCs: mx6 quad, mx6 dual lite and mx6 solo.
For more details about Wandboard, please refer to:
http://www.wandboard.org/
Active arm arm926ejs mxs freescale mx28evk mx28evk_auart_console mx28evk:MXS_AUART,MXS_AUART_BASE=MXS_UARTAPP3_BASE,ENV_IS_IN_MMC Fabio Estevam <fabio.estevam@freescale.com>
Active arm arm926ejs mxs freescale mx28evk mx28evk_nand mx28evk:ENV_IS_IN_NAND Fabio Estevam <fabio.estevam@freescale.com>
Active arm arm926ejs mxs olimex mx23_olinuxino mx23_olinuxino mx23_olinuxino Marek Vasut <marek.vasut@gmail.com>
+Active arm arm926ejs mxs ppcag bg0900 bg0900 bg0900 Marek Vasut <marex@denx.de>
Active arm arm926ejs mxs sandisk sansa_fuze_plus sansa_fuze_plus - Marek Vasut <marek.vasut@gmail.com>
Active arm arm926ejs mxs schulercontrol sc_sps_1 sc_sps_1 - Marek Vasut <marek.vasut@gmail.com>
Active arm arm926ejs nomadik st nhk8815 nhk8815 - Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com>:Alessandro Rubini <rubini@unipv.it>
Active arm armv7 - armltd vexpress vexpress_ca15_tc2 - -
Active arm armv7 - armltd vexpress vexpress_ca5x2 - Matt Waddel <matt.waddel@linaro.org>
Active arm armv7 - armltd vexpress vexpress_ca9x4 - Matt Waddel <matt.waddel@linaro.org>
-Active arm armv7 am33xx isee igep0033 igep0033 - Enric Balletbo i Serra <eballetbo@iseebcn.com>
+Active arm armv7 am33xx isee igep0033 am335x_igep0033 - Enric Balletbo i Serra <eballetbo@iseebcn.com>
Active arm armv7 am33xx phytec pcm051 pcm051 pcm051 Lars Poeschel <poeschel@lemonage.de>
Active arm armv7 am33xx siemens dxr2 dxr2 - Roger Meier <r.meier@siemens.com>
Active arm armv7 am33xx siemens pxm2 pxm2 - Roger Meier <r.meier@siemens.com>
Active arm armv7 mx5 genesi mx51_efikamx mx51_efikamx mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKAMX,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_mx.cfg -
Active arm armv7 mx5 genesi mx51_efikamx mx51_efikasb mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKASB,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_sb.cfg -
Active arm armv7 mx5 ttcontrol vision2 vision2 vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg Stefano Babic <sbabic@denx.de>
+Active arm armv7 mx6 - udoo udoo_quad udoo:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q.cfg,MX6Q,DDR_MB=1024 Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 mx6 - wandboard wandboard_dl wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024 Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 mx6 - wandboard wandboard_quad wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048 Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 mx6 - wandboard wandboard_solo wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 omap3 comelit dig297 dig297 - Luca Ceresoli <luca.ceresoli@comelit.it>
Active arm armv7 omap3 compulab cm_t35 cm_t35 - Igor Grinberg <grinberg@compulab.co.il>
Active arm armv7 omap3 corscience tricorder tricorder - Thomas Weber <weber@corscience.de>
+Active arm armv7 omap3 corscience tricorder tricorder_flash tricorder:FLASHCARD Thomas Weber <weber@corscience.de>
Active arm armv7 omap3 htkw mcx mcx - Ilya Yanok <yanok@emcraft.com>
-Active arm armv7 omap3 isee igep00x0 igep0020 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
-Active arm armv7 omap3 isee igep00x0 igep0020_nand igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_NAND -
-Active arm armv7 omap3 isee igep00x0 igep0030 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
-Active arm armv7 omap3 isee igep00x0 igep0030_nand igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND -
-Active arm armv7 omap3 isee igep00x0 igep0032 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
+Active arm armv7 omap3 isee igep00x0 igep0020 omap3_igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
+Active arm armv7 omap3 isee igep00x0 igep0020_nand omap3_igep00x0:MACH_TYPE=MACH_TYPE_IGEP0020,BOOT_NAND -
+Active arm armv7 omap3 isee igep00x0 igep0030 omap3_igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
+Active arm armv7 omap3 isee igep00x0 igep0030_nand omap3_igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND -
+Active arm armv7 omap3 isee igep00x0 igep0032 omap3_igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND Enric Balletbo i Serra <eballetbo@iseebcn.com>
Active arm armv7 omap3 logicpd am3517evm am3517_evm - Vaibhav Hiremath <hvaibhav@ti.com>
Active arm armv7 omap3 logicpd omap3som omap3_logic - Peter Barada <peter.barada@logicpd.com>
Active arm armv7 omap3 logicpd zoom1 omap3_zoom1 - Nishanth Menon <nm@ti.com>
Active arm armv7 omap3 timll devkit8000 devkit8000 - Thomas Weber <weber@corscience.de>
Active arm armv7 omap4 ti panda omap4_panda - Sricharan R <r.sricharan@ti.com>
Active arm armv7 omap4 ti sdp4430 omap4_sdp4430 - Sricharan R <r.sricharan@ti.com>
-Active arm armv7 omap5 ti dra7xx dra7xx_evm - Lokesh Vutla <lokeshvutla@ti.com>
+Active arm armv7 omap5 ti dra7xx dra7xx_evm dra7xx_evm:CONS_INDEX=1 Lokesh Vutla <lokeshvutla@ti.com>
+Active arm armv7 omap5 ti dra7xx dra7xx_evm_uart3 dra7xx_evm:CONS_INDEX=3,SPL_YMODEM_SUPPORT Lokesh Vutla <lokeshvutla@ti.com>
Active arm armv7 omap5 ti omap5_uevm omap5_uevm - -
Active arm armv7 rmobile atmark-techno armadillo-800eva armadillo-800eva - Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Active arm armv7 rmobile kmc kzm9g kzm9g - Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>:Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Active arm ixp - - actux1 actux1_4_32 actux1:FLASH2X2,RAM_32MB Michael Schwingen <michael@schwingen.org>
Active arm ixp - - actux1 actux1_8_16 actux1:FLASH1X8 Michael Schwingen <michael@schwingen.org>
Active arm ixp - - actux1 actux1_8_32 actux1:FLASH1X8,RAM_32MB Michael Schwingen <michael@schwingen.org>
-Active arm ixp - prodrive pdnb3 pdnb3 - Stefan Roese <sr@denx.de>
-Active arm ixp - prodrive pdnb3 scpu pdnb3:SCPU Stefan Roese <sr@denx.de>
Active arm pxa - - - balloon3 - Marek Vasut <marek.vasut@gmail.com>
Active arm pxa - - - h2200 - Lukasz Dalek <luk0104@gmail.com>
Active arm pxa - - - palmld - Marek Vasut <marek.vasut@gmail.com>
1) Prerequisites
----------------
-To make a MXS based board bootable, some tools are necessary. The first one is
-the "elftosb" tool distributed by Freescale Semiconductor. The other one is the
-"mxsboot" tool found in U-Boot source tree.
+To make a MXS based board bootable, some tools are necessary. The only
+mandatory tool is the "mxsboot" tool found in U-Boot source tree. The
+tool is built automatically when compiling U-Boot for i.MX23 or i.MX28.
+
+The production of BootStream image is handled via "mkimage", which is
+also part of the U-Boot source tree. The "mkimage" requires OpenSSL
+development libraries to be installed. In case of Debian and derivates,
+this is installed by running:
+
+ $ sudo apt-get install libssl-dev
+
+NOTE: The "elftosb" tool distributed by Freescale Semiconductor is no
+ longer necessary for general use of U-Boot on i.MX23 and i.MX28.
+ The mkimage supports generation of BootStream images encrypted
+ with a zero key, which is the vast majority of use-cases. In
+ case you do need to produce image encrypted with non-zero key
+ or other special features, please use the "elftosb" tool,
+ otherwise continue to section 2). The installation procedure of
+ the "elftosb" is outlined below:
Firstly, obtain the elftosb archive from the following location:
Make sure the "elftosb" binary can be found in your $PATH, in this case this
means "/usr/local/bin/" has to be in your $PATH.
-Install the 'libssl-dev' package as well. On a Debian-based distribution, this
-package can be installed as follows:
-
- $ sudo apt-get install libssl-dev
-
2) Compiling U-Boot for a MXS based board
-------------------------------------------
proper header to allow successful boot from SD or NAND. Adding the header is
discussed in the following chapters.
+NOTE: The process that produces u-boot.sb uses the mkimage to generate the
+ BootStream. The BootStream is encrypted with zero key. In case you need
+ some special features of the BootStream and plan on using the "elftosb"
+ tool instead, the invocation to produce a compatible BootStream with the
+ one produced by mkimage is outlined below. For further details, refer to
+ the documentation bundled with the "elftosb" package.
+
+ $ elftosb -zf imx23 -c arch/arm/cpu/arm926ejs/mxs/u-boot-imx23.bd \
+ -o u-boot.sb
+ $ elftosb -zf imx28 -c arch/arm/cpu/arm926ejs/mxs/u-boot-imx28.bd \
+ -o u-boot.sb
+
3) Installation of U-Boot for a MXS based board to SD card
----------------------------------------------------------
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-omap1510inn arm arm925t - - Kshitij Gupta <kshitij@ti.com>
+pdnb3 arm ixp - 2013-09-24 Stefan Roese <sr@denx.de>
+scpu arm ixp - 2013-09-24 Stefan Roese <sr@denx.de>
+omap1510inn arm arm925t 0610a16 2013-09-23 Kshitij Gupta <kshitij@ti.com>
CANBT powerpc 405CR fb8f4fd 2013-08-07 Matthias Fuchs <matthias.fuchs@esd.eu>
Alaska8220 powerpc mpc8220 d6ed322 2013-05-11
Yukon8220 powerpc mpc8220 d6ed322 2013-05-11
obj-$(CONFIG_AT91SAM9XE) += bootcount_at91.o
obj-$(CONFIG_BLACKFIN) += bootcount_blackfin.o
obj-$(CONFIG_SOC_DA8XX) += bootcount_davinci.o
+obj-$(CONFIG_AM33XX) += bootcount_davinci.o
obj-$(CONFIG_BOOTCOUNT_RAM) += bootcount_ram.o
*/
#include <bootcount.h>
-#include <asm/arch/da850_lowlevel.h>
-#include <asm/arch/davinci_misc.h>
+#include <asm/davinci_rtc.h>
void bootcount_store(ulong a)
{
*/
writel(RTC_KICK0R_WE, ®->kick0r);
writel(RTC_KICK1R_WE, ®->kick1r);
- raw_bootcount_store(®->scratch0, a);
- raw_bootcount_store(®->scratch1, BOOTCOUNT_MAGIC);
+ raw_bootcount_store(®->scratch2,
+ (BOOTCOUNT_MAGIC & 0xffff0000) | (a & 0x0000ffff));
}
ulong bootcount_load(void)
{
+ unsigned long val;
struct davinci_rtc *reg =
(struct davinci_rtc *)CONFIG_SYS_BOOTCOUNT_ADDR;
- if (raw_bootcount_load(®->scratch1) != BOOTCOUNT_MAGIC)
+ val = raw_bootcount_load(®->scratch2);
+ if ((val & 0xffff0000) != (BOOTCOUNT_MAGIC & 0xffff0000))
return 0;
else
- return raw_bootcount_load(®->scratch0);
+ return val & 0x0000ffff;
}
static struct nand_ecclayout nand_davinci_4bit_layout_oobfirst = {
#if defined(CONFIG_SYS_NAND_PAGE_2K)
.eccbytes = 40,
+#ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
+ .eccpos = {
+ 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,
+ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+ 38, 39, 40, 41, 42, 43, 44, 45, 46, 47,
+ 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,
+ },
+ .oobfree = {
+ {2, 4}, {16, 6}, {32, 6}, {48, 6},
+ },
+#else
.eccpos = {
24, 25, 26, 27, 28,
29, 30, 31, 32, 33, 34, 35, 36, 37, 38,
.oobfree = {
{.offset = 2, .length = 22, },
},
+#endif /* #ifdef CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC */
#elif defined(CONFIG_SYS_NAND_PAGE_4K)
.eccbytes = 80,
.eccpos = {
return config;
}
+/*
+ * Get the DMA bus width field of the network configuration register that we
+ * should program. We find the width from decoding the design configuration
+ * register to find the maximum supported data bus width.
+ */
+static u32 macb_dbw(struct macb_device *macb)
+{
+ switch (GEM_BFEXT(DBWDEF, gem_readl(macb, DCFG1))) {
+ case 4:
+ return GEM_BF(DBW, GEM_DBW128);
+ case 2:
+ return GEM_BF(DBW, GEM_DBW64);
+ case 1:
+ default:
+ return GEM_BF(DBW, GEM_DBW32);
+ }
+}
+
int macb_eth_initialize(int id, void *regs, unsigned int phy_addr)
{
struct macb_device *macb;
*/
if (macb_is_gem(macb)) {
ncfgr = gem_mdc_clk_div(id, macb);
- ncfgr |= GEM_BF(DBW, 1);
+ ncfgr |= macb_dbw(macb);
} else {
ncfgr = macb_mdc_clk_div(id, macb);
}
#define MACB_WOL 0x00c4
#define MACB_MID 0x00fc
+/* GEM specific register offsets */
+#define GEM_DCFG1 0x0280
+
/* Bitfields in NCR */
#define MACB_LB_OFFSET 0
#define MACB_LB_SIZE 1
#define MACB_IDNUM_SIZE 16
/* Bitfields in DCFG1 */
+#define GEM_DBWDEF_OFFSET 25
+#define GEM_DBWDEF_SIZE 3
+
+/* constants for data bus width */
+#define GEM_DBW32 0
+#define GEM_DBW64 1
+#define GEM_DBW128 2
+
/* Constants for CLK */
#define MACB_CLK_DIV8 0
#define MACB_CLK_DIV16 1
#include <command.h>
#include <rtc.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <asm/davinci_rtc.h>
#if defined(CONFIG_CMD_DATE)
int rtc_get(struct rtc_time *tmp)
{
- struct davinci_rtc *rtc = davinci_rtc_base;
+ struct davinci_rtc *rtc = (struct davinci_rtc *)DAVINCI_RTC_BASE;
unsigned long sec, min, hour, mday, wday, mon_cent, year;
unsigned long status;
int rtc_set(struct rtc_time *tmp)
{
- struct davinci_rtc *rtc = davinci_rtc_base;
+ struct davinci_rtc *rtc = (struct davinci_rtc *)DAVINCI_RTC_BASE;
debug("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
void rtc_reset(void)
{
- struct davinci_rtc *rtc = davinci_rtc_base;
+ struct davinci_rtc *rtc = (struct davinci_rtc *)DAVINCI_RTC_BASE;
/* run RTC counter */
writel(0x01, &rtc->ctrl);
{
at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC;
-#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
- defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20) || \
- defined(CONFIG_AT91SAM9261)
+#ifdef CONFIG_USB_ATMEL_CLK_SEL_PLLB
/* Enable PLLB */
writel(get_pllb_init(), &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != AT91_PMC_LOCKB)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
- defined(CONFIG_AT91SAM9X5) || defined(CONFIG_SAMA5D3)
+#ifdef CONFIG_AT91SAM9N12
+ writel(AT91_PMC_USBS_USB_PLLB | AT91_PMC_USB_DIV_2, &pmc->usb);
+#endif
+#elif defined(CONFIG_USB_ATMEL_CLK_SEL_UPLL)
/* Enable UPLL */
writel(readl(&pmc->uckr) | AT91_PMC_UPLLEN | AT91_PMC_BIASEN,
&pmc->uckr);
writel(ATMEL_PMC_UHP, &pmc->scdr);
#endif
-#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || \
- defined(CONFIG_AT91SAM9263) || defined(CONFIG_AT91SAM9G20)
+#ifdef CONFIG_USB_ATMEL_CLK_SEL_PLLB
+#ifdef CONFIG_AT91SAM9N12
+ writel(0, &pmc->usb);
+#endif
/* Disable PLLB */
writel(0, &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != 0)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
- defined(CONFIG_AT91SAM9X5) || defined(CONFIG_SAMA5D3)
+#elif defined(CONFIG_USB_ATMEL_CLK_SEL_UPLL)
/* Disable UPLL */
writel(readl(&pmc->uckr) & (~AT91_PMC_UPLLEN), &pmc->uckr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKU) == AT91_PMC_LOCKU)
#define WCR_WDBG 0x02
#define WCR_WDE 0x04 /* WDOG enable */
#define WCR_WDT 0x08
+#define WCR_SRS 0x10
#define WCR_WDW 0x80
#define SET_WCR_WT(x) (x << 8)
#define CONFIG_WATCHDOG_TIMEOUT_MSECS 128000
#endif
timeout = (CONFIG_WATCHDOG_TIMEOUT_MSECS / 500) - 1;
- writew(WCR_WDZST | WCR_WDBG | WCR_WDE | WCR_WDT |
+ writew(WCR_WDZST | WCR_WDBG | WCR_WDE | WCR_WDT | WCR_SRS |
WCR_WDW | SET_WCR_WT(timeout), &wdog->wcr);
hw_watchdog_reset();
}
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
* USB Config
*/
#define CONFIG_USB_ATMEL 1
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_KEYBOARD 1
#define CONFIG_USB_STORAGE 1
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_CMD_SF
#define CONFIG_CMD_MMC
#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x26e00000
+/* USB host */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9n12"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
+#define CONFIG_USB_STORAGE
+#endif
+
#ifdef CONFIG_SYS_USE_SPIFLASH
/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#else
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9x5"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
#endif
-#define CONFIG_USB_ATMEL
#define CONFIG_USB_STORAGE
#endif
--- /dev/null
+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __CONFIGS_BG0900_H__
+#define __CONFIGS_BG0900_H__
+
+/* System configurations */
+#define CONFIG_MX28 /* i.MX28 SoC */
+
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+
+/* Memory configuration */
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x10000000 /* Max 256 MB RAM */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Environment */
+#define CONFIG_ENV_SIZE (16 * 1024)
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_IS_NOWHERE
+
+/* FEC Ethernet on SoC */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_NET_MULTI
+#endif
+
+/* SPI */
+#ifdef CONFIG_CMD_SPI
+#define CONFIG_DEFAULT_SPI_BUS 2
+#define CONFIG_DEFAULT_SPI_CS 0
+#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
+
+/* SPI FLASH */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SF_DEFAULT_BUS 2
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 40000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
+#define CONFIG_ENV_SPI_BUS 2
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 40000000
+#define CONFIG_ENV_SPI_MODE SPI_MODE_0
+#endif
+
+#endif
+
+/* Boot Linux */
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_BOOTARGS "console=ttyAMA0,115200"
+#define CONFIG_BOOTCOMMAND "bootm"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/* Extra Environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "update_spi_firmware_filename=u-boot.sb\0" \
+ "update_spi_firmware_maxsz=0x80000\0" \
+ "update_spi_firmware=" /* Update the SPI flash firmware */ \
+ "if sf probe 2:0 ; then " \
+ "if tftp ${update_spi_firmware_filename} ; then " \
+ "sf erase 0x0 +${filesize} ; " \
+ "sf write ${loadaddr} 0x0 ${filesize} ; " \
+ "fi ; " \
+ "fi\0"
+
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_BG0900_H__ */
#define CONFIG_OMAP /* in a TI OMAP core */
#define CONFIG_OMAP34XX /* which is a 34XX */
#define CONFIG_OMAP_GPIO
+#define CONFIG_CMD_GPIO
#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
#define CONFIG_OMAP_COMMON
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
-#define CONFIG_BOOTDELAY 10
+#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_EXTRA_ENV_SETTINGS \
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#if defined(CONFIG_CMD_USB)
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_CMD_SAVEENV
+#if (CONFIG_CONS_INDEX == 1)
#define CONSOLEDEV "ttyO0"
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 UART1_BASE
+#elif (CONFIG_CONS_INDEX == 3)
+#define CONSOLEDEV "ttyO2"
+#endif
+#define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has UART0 */
+#define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */
+#define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_OMAP_ABE_SYSCK
#define CONFIG_SYS_TEXT_BASE 0x00000000
#else
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SYS_TEXT_BASE 0x21f00000
+#define CONFIG_SYS_TEXT_BASE 0x21800000
#endif
#define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */
#define CONFIG_STANDALONE_LOAD_ADDR 0x21000000
#define CONFIG_CMD_UBI
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_UBIFS
+
#define CONFIG_SYS_LONGHELP
/*
* Hardware drivers
*/
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_AT91C_PQFP_UHPBUG
#define CONFIG_USB_STORAGE
/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000
(3 << DV_DDR_SDCR_IBANK_SHIFT) | \
(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
-#define CONFIG_SYS_DA850_CS3CFG (DAVINCI_ABCR_WSETUP(2) | \
+#define CONFIG_SYS_DA850_CS3CFG (DAVINCI_ABCR_WSETUP(1) | \
DAVINCI_ABCR_WSTROBE(2) | \
- DAVINCI_ABCR_WHOLD(1) | \
+ DAVINCI_ABCR_WHOLD(0) | \
DAVINCI_ABCR_RSETUP(1) | \
- DAVINCI_ABCR_RSTROBE(4) | \
- DAVINCI_ABCR_RHOLD(0) | \
- DAVINCI_ABCR_TA(1) | \
+ DAVINCI_ABCR_RSTROBE(2) | \
+ DAVINCI_ABCR_RHOLD(1) | \
+ DAVINCI_ABCR_TA(0) | \
DAVINCI_ABCR_ASIZE_8BIT)
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
CONFIG_SYS_MALLOC_LEN - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { \
- 24, 25, 26, 27, 28, \
- 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
- 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
- 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
- 59, 60, 61, 62, 63 }
+ 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \
+ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
+ 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
+ 54, 55, 56, 57, 58, 59, 60, 61, 62, 63}
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_CMDLINE_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS \
- "mem=128M console=ttyS0,115200n8 root=/dev/mtdblock0p4 rw noinitrd ip=dhcp"
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 2
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "defbootargs=setenv bootargs mem=128M console=ttyS0,115200n8 " \
+ "root=/dev/mtdblock5 rw noinitrd " \
+ "rootfstype=jffs2 noinitrd\0" \
"hwconfig=dsp:wake=yes\0" \
+ "bootcmd=nboot kernel;run defbootargs addmtd;bootm 0xc0700000\0" \
+ "bootfile=uImage\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "mtddevname=uboot-env\0" \
+ "mtddevnum=0\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "u-boot=/tftpboot/ipam390/u-boot.ais\0" \
+ "upd_uboot=tftp c0000000 ${u-boot};nand erase.part u-boot;" \
+ "nand write c0000000 20000 ${filesize}\0" \
"setbootparms=nand read c0100000 200000 400000;" \
+ "run defbootargs addmtd;" \
"spl export atags c0100000;" \
"nand erase.part bootparms;" \
"nand write c0000100 180000 20000\0" \
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
/*
* High Level Configuration Options
*/
-#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP44XX 1 /* which is a 44XX */
#define CONFIG_OMAP4430 1 /* which is in a 4430 */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
+#define CONFIG_MISC_INIT_R
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
+#define CONFIG_SYS_THUMB_BUILD
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define CONFIG_SYS_L2_PL310 1
+#define CONFIG_SYS_PL310_BASE 0x48242000
+#endif
+#define CONFIG_SYS_CACHELINE_SIZE 32
/* Get CPU defs */
#include <asm/arch/cpu.h>
#include <asm/arch/omap.h>
-/* Display CPU and Board Info */
-#define CONFIG_DISPLAY_CPUINFO 1
-#define CONFIG_DISPLAY_BOARDINFO 1
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_REVISION_TAG 1
+/* Use General purpose timer 1 */
+#define CONFIG_SYS_TIMERBASE GPT2_BASE
/*
- * Size of malloc() pool
* Total Size Environment - 128k
- * Malloc - add 256k
*/
#define CONFIG_ENV_SIZE (128 << 10)
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
-/* Vector Base */
-#define CONFIG_SYS_CA9_VECTOR_BASE SRAM_ROM_VECT_BASE
/*
- * Hardware drivers
+ * For the DDR timing information we can either dynamically determine
+ * the timings to use or use pre-determined timings (based on using the
+ * dynamic method. Default to the static timing infomation.
*/
+#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
+#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
+#endif
+
+#include <configs/ti_armv7_common.h>
/*
- * serial port - NS16550 compatible
+ * Hardware drivers
*/
-#define V_NS16550_CLK 48000000
-
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+#define CONFIG_SYS_NS16550_CLK 48000000
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
-
-/* CPU */
-#define CONFIG_ARCH_CPU_INIT
-
-/* I2C */
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_DRIVER_OMAP34XX_I2C 1
-#define CONFIG_I2C_MULTI_BUS 1
-
/* TWL6030 */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_TWL6030_POWER 1
#endif
-/* MMC */
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_MMC 1
-#define CONFIG_OMAP_HSMMC 1
-#define CONFIG_DOS_PARTITION 1
-
-
/* USB */
#define CONFIG_MUSB_UDC 1
#define CONFIG_USB_OMAP3 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-/* Flash */
-#define CONFIG_SYS_NO_FLASH 1
-
-/* commands to include */
-#include <config_cmd_default.h>
-
-/* Enabled commands */
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-
-/* Disabled commands */
+/* Per-Soc commands */
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_IMLS /* List all found images */
/*
* Environment setup
*/
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ENV_VARS_UBOOT_CONFIG
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-
-#define CONFIG_ENV_OVERWRITE
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyO2,115200n8\0" \
"fi; " \
"fi"
-#define CONFIG_AUTO_COMPLETE 1
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_CBSIZE 512
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-
-/*
- * memtest setup
- */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (32 << 20))
-
-/* Default load address */
-#define CONFIG_SYS_LOAD_ADDR 0x80000000
-
-/* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE GPT2_BASE
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*
- * SDRAM Memory Map
- * Even though we use two CS all the memory
- * is mapped to one contiguous block
- */
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define CONFIG_SYS_SDRAM_BASE 0x80000000
-#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
- GENERATED_GBL_DATA_SIZE)
-
-#ifndef CONFIG_SYS_L2CACHE_OFF
-#define CONFIG_SYS_L2_PL310 1
-#define CONFIG_SYS_PL310_BASE 0x48242000
-#endif
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
-/* Defines for SDRAM init */
-#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-
-#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
-#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
-#endif
-
/* Defines for SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40304350
#define CONFIG_SPL_MAX_SIZE (38 * 1024)
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SPL_DISPLAY_PRINT
-
-/*
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 80E7FFC0--0x80E80000 should not be used for any
- * other needs.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80E80000
-
-/*
- * BSS and malloc area 64MB into memory to allow enough
- * space for the kernel at the beginning of memory
- */
-#define CONFIG_SPL_BSS_START_ADDR 0x84000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
-#define CONFIG_SYS_SPL_MALLOC_START 0x84100000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-#define CONFIG_SYS_THUMB_BUILD
-
#endif /* __CONFIG_OMAP4_COMMON_H */
/* ENV related config options */
#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_SYS_PROMPT "Panda # "
-
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#endif /* __CONFIG_PANDA_H */
#define CONFIG_ENV_OFFSET 0xE0000
#define CONFIG_CMD_SAVEENV
-#define CONFIG_SYS_PROMPT "OMAP4430 SDP # "
-
#endif /* __CONFIG_SDP4430_H */
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
- "console=" CONSOLEDEV ",115200n8\0" \
+ "loadaddr=0x80200000\0" \
+ "fdtaddr=0x80F80000\0" \
"fdt_high=0xffffffff\0" \
- "fdtaddr=0x80f80000\0" \
+ "rdaddr=0x81000000\0" \
+ "console=" CONSOLEDEV ",115200n8\0" \
"fdtfile=undefined\0" \
"bootpart=0:2\0" \
"bootdir=/boot\0" \
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
+++ /dev/null
-/*
- * (C) Copyright 2006-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * Configuation settings for the PDNB3 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_IXP425 1 /* This is an IXP425 CPU */
-#define CONFIG_PDNB3 1 /* on an PDNB3 board */
-
-#define CONFIG_MACH_TYPE 1002
-
-#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
-#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
-
-/*
- * Ethernet
- */
-#define CONFIG_IXP4XX_NPE 1 /* include IXP4xx NPE support */
-#define CONFIG_PHY_ADDR 16 /* NPE0 PHY address */
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR 18 /* NPE1 PHY address */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
-
-/*
- * Misc configuration options
- */
-#define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */
-#define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1 << 20)
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_IXP_SERIAL
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_PING
-
-#if !defined(CONFIG_SCPU)
-#define CONFIG_CMD_NAND
-#endif
-
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
-
-#define CONFIG_IXP425_TIMER_CLK 66666666
-
-/***************************************************************
- * Platform/Board specific defines start here.
- ***************************************************************/
-
-/*-----------------------------------------------------------------------
- * Default configuration (environment varibles...)
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=pdnb3\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} ethaddr=${ethaddr} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate} " \
- "mtdparts=${mtdparts}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/buildroot\0" \
- "bootfile=/tftpboot/netbox/uImage\0" \
- "kernel_addr=50080000\0" \
- "ramdisk_addr=50200000\0" \
- "load=tftp 100000 /tftpboot/netbox/u-boot.bin\0" \
- "update=protect off 50000000 5007dfff;era 50000000 5007dfff;" \
- "cp.b 100000 50000000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "ipaddr=10.0.0.233\0" \
- "serverip=10.0.0.152\0" \
- "netmask=255.255.0.0\0" \
- "ethaddr=c6:6f:13:36:f3:81\0" \
- "eth1addr=c6:6f:13:36:f3:82\0" \
- "mtdparts=IXP4XX-Flash.0:504k@0(uboot),4k@504k(env)," \
- "4k@508k(renv)\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-
-#define CONFIG_SYS_TEXT_BASE 0x50000000
-#define CONFIG_SYS_FLASH_BASE 0x50000000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#if defined(CONFIG_SCPU)
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 512 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (504 << 10) /* Reserve 512 kB for Monitor */
-#endif
-
-/*
- * Expansion bus settings
- */
-#if defined(CONFIG_SCPU)
-#define CONFIG_SYS_EXP_CS0 0x94d23C42 /* 8bit, max size */
-#else
-#define CONFIG_SYS_EXP_CS0 0x94913C43 /* 8bit, max size */
-#endif
-#define CONFIG_SYS_EXP_CS1 0x85000043 /* 8bit, 512bytes */
-
-/*
- * SDRAM settings
- */
-#define CONFIG_SYS_SDR_CONFIG 0x18
-#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
-#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
-
-/*
- * FLASH and environment organization
- */
-#if defined(CONFIG_SCPU)
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
-#endif
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-#if defined(CONFIG_SCPU)
-/* no redundant environment on SCPU */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-#else
-#define CONFIG_ENV_SECT_SIZE 0x1000 /* size of one complete sector */
-#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif
-
-#if !defined(CONFIG_SCPU)
-/*
- * NAND-FLASH stuff
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x51000000 /* NAND FLASH Base Address */
-#endif
-
-/*
- * GPIO settings
- */
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_GPIO_PRG 12 /* FPGA program pin (cpu output)*/
-#define CONFIG_SYS_GPIO_CLK 10 /* FPGA clk pin (cpu output) */
-#define CONFIG_SYS_GPIO_DATA 14 /* FPGA data pin (cpu output) */
-#define CONFIG_SYS_GPIO_INIT 13 /* FPGA init pin (cpu input) */
-#define CONFIG_SYS_GPIO_DONE 11 /* FPGA done pin (cpu input) */
-
-/* other GPIO's */
-#define CONFIG_SYS_GPIO_RESTORE_INT 0
-#define CONFIG_SYS_GPIO_RESTART_INT 1
-#define CONFIG_SYS_GPIO_SYS_RUNNING 2
-#define CONFIG_SYS_GPIO_PCI_INTA 3
-#define CONFIG_SYS_GPIO_PCI_INTB 4
-#define CONFIG_SYS_GPIO_I2C_SCL 6
-#define CONFIG_SYS_GPIO_I2C_SDA 7
-#define CONFIG_SYS_GPIO_FPGA_RESET 9
-#define CONFIG_SYS_GPIO_CLK_33M 15
-
-/*
- * I2C stuff
- */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL (1 << CONFIG_SYS_GPIO_I2C_SCL)
-#define PB_SDA (1 << CONFIG_SYS_GPIO_I2C_SDA)
-
-#define I2C_INIT GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SCL)
-#define I2C_ACTIVE GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_I2C_SDA)
-#define I2C_TRISTATE GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_I2C_SDA)
-#define I2C_READ ((*IXP425_GPIO_GPINR & PB_SDA) != 0)
-#define I2C_SDA(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SDA); \
- else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SDA)
-#define I2C_SCL(bit) if (bit) GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_I2C_SCL); \
- else GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_I2C_SCL)
-#define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */
-
-/*
- * I2C RTC
- */
-#if 0 /* test-only */
-#define CONFIG_RTC_DS1340 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#else
-/* M41T11 Serial Access Timekeeper(R) SRAM */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with the linux driver */
-#endif
-
-/*
- * Spartan3 FPGA configuration support
- */
-#define CONFIG_SYS_FPGA_MAX_SIZE 700*1024 /* 700kByte for XC3S500E */
-
-#define CONFIG_SYS_FPGA_PRG (1 << CONFIG_SYS_GPIO_PRG) /* FPGA program pin (cpu output)*/
-#define CONFIG_SYS_FPGA_CLK (1 << CONFIG_SYS_GPIO_CLK) /* FPGA clk pin (cpu output) */
-#define CONFIG_SYS_FPGA_DATA (1 << CONFIG_SYS_GPIO_DATA) /* FPGA data pin (cpu output) */
-#define CONFIG_SYS_FPGA_INIT (1 << CONFIG_SYS_GPIO_INIT) /* FPGA init pin (cpu input) */
-#define CONFIG_SYS_FPGA_DONE (1 << CONFIG_SYS_GPIO_DONE) /* FPGA done pin (cpu input) */
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
/* USB configuration */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
#define CONFIG_MII /* Required in net/eth.c */
+/*
+ * RTC related defines. To use bootcount you must set bootlimit in the
+ * environment to a non-zero value.
+ */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000
+
+/* Enable the HW watchdog, since we can use this with bootcount */
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_OMAP_WATCHDOG
+
/*
* SPL related defines. The Public RAM memory map the ROM defines the
* area between 0x402F0400 and 0x4030B800 as a download area and
#define CONFIG_SPL_TEXT_BASE 0x402F0400
#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE)
+/* Enable the watchdog inside of SPL */
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+
/*
* Since SPL did pll and ddr initialization for us,
* we don't need to do it twice.
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000
/* FAT */
#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SILENT_CONSOLE
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
#define CONFIG_OF_LIBFDT
/* Size of malloc() pool */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
- /* Sector */
#define CONFIG_SYS_MALLOC_LEN (1024*1024)
/* Hardware drivers */
+/* GPIO support */
+#define CONFIG_OMAP_GPIO
+
+/* LED support */
+#define CONFIG_STATUS_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define CONFIG_CMD_LED /* LED command */
+#define STATUS_LED_BIT (1 << 0)
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1 (1 << 1)
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT2 (1 << 2)
+#define STATUS_LED_STATE2 STATUS_LED_ON
+#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
+
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
+#define CONFIG_I2C_MULTI_BUS
+
+/* EEPROM */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_BUS_NUM 1
/* TWL4030 */
#define CONFIG_TWL4030_POWER
/* Board NAND Info */
#define CONFIG_SYS_NO_FLASH /* no NOR flash */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define MTDIDS_DEFAULT "nand0=nand"
-#define MTDPARTS_DEFAULT "mtdparts=nand:" \
- "512k(u-boot-spl)," \
- "1920k(u-boot)," \
- "128k(u-boot-env)," \
- "4m(kernel)," \
- "-(fs)"
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
+ "128k(SPL)," \
+ "1m(u-boot)," \
+ "384k(u-boot-env1)," \
+ "1152k(mtdoops)," \
+ "384k(u-boot-env2)," \
+ "5m(kernel)," \
+ "2m(fdt)," \
+ "-(ubi)"
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
-/* Environment information */
-#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
+/* Environment information (this is the common part) */
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 0
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
+/* hang() the board on panic() */
+#define CONFIG_PANIC_HANG
+
+/* environment placement (for NAND), is different for FLASHCARD but does not
+ * harm there */
+#define CONFIG_ENV_OFFSET 0x120000 /* env start */
+#define CONFIG_ENV_OFFSET_REDUND 0x2A0000 /* redundant env start */
+#define CONFIG_ENV_SIZE (16 << 10) /* use 16KiB for env */
+#define CONFIG_ENV_RANGE (384 << 10) /* allow badblocks in env */
+
+/* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend
+ * value can not be used here! */
+#define CONFIG_LOADADDR 0x82000000
+
+#define CONFIG_COMMON_ENV_SETTINGS \
"console=ttyO2,115200n8\0" \
"mmcdev=0\0" \
- "vram=12M\0" \
- "lcdmode=800x600\0" \
+ "vram=3M\0" \
"defaultdisplay=lcd\0" \
- "kernelopts=rw rootwait\0" \
+ "kernelopts=mtdoops.mtddev=3\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
"commonargs=" \
"setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${kernelopts} " \
+ "vt.global_cursor_default=0 " \
"vram=${vram} " \
- "omapfb.mode=lcd:${lcdmode} " \
- "omapdss.def_disp=${defaultdisplay}\0" \
+ "omapdss.def_disp=${defaultdisplay}\0"
+
+#define CONFIG_BOOTCOMMAND "run autoboot"
+
+/* specific environment settings for different use cases
+ * FLASHCARD: used to run a rdimage from sdcard to program the device
+ * 'NORMAL': used to boot kernel from sdcard, nand, ...
+ *
+ * The main aim for the FLASHCARD skin is to have an embedded environment
+ * which will not be influenced by any data already on the device.
+ */
+#ifdef CONFIG_FLASHCARD
+
+#define CONFIG_ENV_IS_NOWHERE
+
+/* the rdaddr is 16 MiB before the loadaddr */
+#define CONFIG_ENV_RDADDR "rdaddr=0x81000000\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_COMMON_ENV_SETTINGS \
+ CONFIG_ENV_RDADDR \
+ "autoboot=" \
+ "run commonargs; " \
+ "setenv bootargs ${bootargs} " \
+ "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \
+ "rdinit=/sbin/init; " \
+ "mmc dev ${mmcdev}; mmc rescan; " \
+ "fatload mmc ${mmcdev} ${loadaddr} uImage; " \
+ "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \
+ "bootm ${loadaddr} ${rdaddr}\0"
+
+#else /* CONFIG_FLASHCARD */
+
+#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
+
+#define CONFIG_ENV_IS_IN_NAND
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_COMMON_ENV_SETTINGS \
"mmcargs=" \
"run commonargs; " \
"setenv bootargs ${bootargs} " \
"root=/dev/mmcblk0p2 " \
- "${kernelopts}\0" \
+ "rootwait " \
+ "rw\0" \
"nandargs=" \
"run commonargs; " \
"setenv bootargs ${bootargs} " \
- "omapfb.mode=lcd:${lcdmode} " \
- "omapdss.def_disp=${defaultdisplay} " \
"root=ubi0:root " \
- "ubi.mtd=4 " \
+ "ubi.mtd=7 " \
"rootfstype=ubifs " \
- "${kernelopts}\0" \
+ "ro\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
- "eraseenv=nand unlock 0x260000 0x20000; nand erase 0x260000 0x20000\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
- "loaduimage_ubi=mtd default; " \
- "ubi part fs; " \
+ "loaduimage_ubi=ubi part ubi; " \
"ubifsmount ubi:root; " \
"ubifsload ${loadaddr} /boot/uImage\0" \
+ "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
- "run loaduimage_ubi; " \
+ "run loaduimage_nand; " \
"bootm ${loadaddr}\0" \
"autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"fi; " \
"else run nandboot; fi\0"
-
-#define CONFIG_BOOTCOMMAND "run autoboot"
+#endif /* CONFIG_FLASHCARD */
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_CMDLINE_EDITING /* enable cmdline history */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_PROMPT "OMAP3 Tricorder # "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x07000000)
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x00000000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
- 0x01000000) /* 16MB */
+ 0x07000000) /* 112 MB */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000)
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
-
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
-#define CONFIG_SPL_MAX_SIZE (55 * 1024) /* 7 KB for stack */
+#define CONFIG_SPL_MAX_SIZE (57 * 1024) /* 7 KB for stack */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
#define CONFIG_SPL_BSS_START_ADDR 0x80000000 /*CONFIG_SYS_SDRAM_BASE*/
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x81000000
#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for Udoo board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+#include <asm/sizes.h>
+
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define MACH_TYPE_UDOO 4800
+#define CONFIG_MACH_TYPE MACH_TYPE_UDOO
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART2_BASE
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_SETEXPR
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
+#define CONFIG_LOADADDR 0x12000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+/* MMC Configuration */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_DEFAULT_FDT_FILE "imx6q-udoo.dtb"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "uimage=uImage\0" \
+ "console=ttymxc1\0" \
+ "splashpos=m,m\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "fdt_addr=0x11000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+ "update_sd_firmware_filename=u-boot.imx\0" \
+ "update_sd_firmware=" \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "if mmc dev ${mmcdev}; then " \
+ "if ${get_cmd} ${update_sd_firmware_filename}; then " \
+ "setexpr fw_sz ${filesize} / 0x200; " \
+ "setexpr fw_sz ${fw_sz} + 1; " \
+ "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+ "fi; " \
+ "fi\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${uimage}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE (8 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#endif /* __CONFIG_H * */
/* USB */
#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
#define CONFIG_USB_OHCI_NEW
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_USB_OHCI_CPU_INIT
projects / karo-tx-uboot.git / commitdiff