Active powerpc ppc4xx - xilinx ppc405-generic xilinx-ppc405-generic_flash xilinx-ppc405-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC Ricardo Ribalda <ricardo.ribalda@uam.es>
Active powerpc ppc4xx - xilinx ppc440-generic xilinx-ppc440-generic xilinx-ppc440-generic:SYS_TEXT_BASE=0x04000000,RESET_VECTOR_ADDRESS=0x04100000,BOOT_FROM_XMD=1 Ricardo Ribalda <ricardo.ribalda@uam.es>
Active powerpc ppc4xx - xilinx ppc440-generic xilinx-ppc440-generic_flash xilinx-ppc440-generic:SYS_TEXT_BASE=0xF7F60000,RESET_VECTOR_ADDRESS=0xF7FFFFFC Ricardo Ribalda <ricardo.ribalda@uam.es>
-Active sandbox sandbox - - <none> sandbox - Simon Glass <sjg@chromium.org>
+Active sandbox sandbox - - sandbox sandbox - Simon Glass <sjg@chromium.org>
Active sh sh2 - renesas rsk7203 rsk7203 - Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>:Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Active sh sh2 - renesas rsk7264 rsk7264 - Phil Edworthy <phil.edworthy@renesas.com>
Active sh sh2 - renesas rsk7269 rsk7269 - -
*/
#define TWSI_FREQUENCY(m, n) \
- ((u8) (CONFIG_SYS_TCLK / (10 * (m + 1) * 2 * (1 << n))))
-
-/*
- * These are required to be reprogrammed before enabling the controller
- * because a reset loses them.
- * Default values come from the spec, but a twsi_reset will change them.
- * twsi_slave_address left uninitialized lest checkpatch.pl complains.
- */
-
-/* Baudrate generator: m (bits 7..4) =4, n (bits 3..0) =4 */
-static u8 twsi_baud_rate = 0x44; /* baudrate at controller reset */
-/* Default frequency corresponding to default m=4, n=4 */
-static u8 twsi_actual_speed = TWSI_FREQUENCY(4, 4);
-/* Default slave address is 0 (so is an uninitialized static) */
-static u8 twsi_slave_address;
+ (CONFIG_SYS_TCLK / (10 * (m + 1) * (1 << n)))
/*
* Reset controller.
* Controller reset also resets the baud rate and slave address, so
* re-establish them.
*/
-static void twsi_reset(void)
+static void twsi_reset(u8 baud_rate, u8 slave_address)
{
/* ensure controller will be enabled by any twsi*() function */
twsi_control_flags = MVTWSI_CONTROL_TWSIEN;
/* wait 2 ms -- this is what the Marvell LSP does */
udelay(20000);
/* set baud rate */
- writel(twsi_baud_rate, &twsi->baudrate);
+ writel(baud_rate, &twsi->baudrate);
/* set slave address even though we don't use it */
- writel(twsi_slave_address, &twsi->slave_address);
+ writel(slave_address, &twsi->slave_address);
writel(0, &twsi->xtnd_slave_addr);
/* assert STOP but don't care for the result */
(void) twsi_stop(0);
}
}
}
- /* save baud rate and slave for later calls to twsi_reset */
- twsi_baud_rate = baud;
- twsi_actual_speed = highest_speed;
- twsi_slave_address = slaveadd;
/* reset controller */
- twsi_reset();
+ twsi_reset(baud, slaveadd);
}
/*