Commit 3ff291f371fa9858426774f3732924bacb61ed1c
(kconfig: convert Kconfig helper script into a shell script)
restored "<board>_config" target for backward compatibility.
It should be documented.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
Stefan Roese [Mon, 25 Aug 2014 09:26:19 +0000 (11:26 +0200)]
net: cpsw: am335x: Drop constant link checking from rx/tx path's
We noticed on the DXR2 platform (AM335x with a SMSC LAN9303 switch connected
to the CPSW MAC) that the network performance in U-Boot is quite poor. Only
when the transfer is started without a cable connected, and the cable is
plugged after the first timeout "T" occured, an increased in performance
can be seen. Debugging has revealed, that the cpsw driver has constant
link checking builtin into the rx and tx functions. This results in the
bad performance and seems to be unnecessary. The link has already been
checked in the init function, before the transfer is started. This usually
is sufficient.
BTW: I have seen no other network driver in U-Boot so far, that constantly
checks for link in the rx / tx functions.
The performance numbers on the DXR2 board are:
0.56 MiB/s cpsw_check_link() in rx and tx path
0.87 MiB/s cpsw_check_link() only in tx path
1.0 MiB/s cpsw_check_link() only in rx path
2.7 MiB/s no cpsw_check_link() in rx and tx path
So with this patch the network performance on DXR2 increases from 0.56
to 2.7 MiB/s (nearly 5 times as fast).
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Samuel Egli <samuel.egli@siemens.com> Tested-by: Heiko Schocher <hs@denx.de> Cc: Vladimir Koutny <vladimir.koutny@streamunlimited.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Tom Rini <trini@ti.com>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:48 +0000 (12:39 +0900)]
tools/genboardscfg.py: improve performance
I guess some developers are already getting sick of this tool
because it generally takes a few minites to generate the boards.cfg
on a reasonable computer.
The idea popped up on my mind was to skip Makefiles and
to run script/kconfig/conf directly.
This tool should become about 4 times faster.
You might still not be satisfied, but better than doing nothing.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:46 +0000 (12:39 +0900)]
tools/genboardscfg.py: fix minor problems on termination
This tool deletes the incomplete boards.cfg
if it encounters an error or is is terminated by the user.
I notice some problems even though they rarely happen.
[1] The boards.cfg is removed if the program is terminated
during __gen_boards_cfg() function but before boards.cfg
is actually touched. In this case, the previous boards.cfg
should be kept as it is.
[2] If an error occurs while deleting the incomplete boards.cfg,
the program throws another exception. This hides the privious
exception and we will not be able to know the real cause.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:45 +0000 (12:39 +0900)]
tools/genboardscfg.py: wait for unfinished subprocesses before error-out
When an error occurs or the program is terminated by the user
on the way, the destructer __del__ of class Slot is invoked and
the work directories are removed.
We have to make sure there are no subprocesses (in this case,
"make O=<work_dir> ...") using the work directories before
removing them. Otherwise the subprocess spits a bunch of error
messages possibly causing more problems. Perhaps some users
may get upset to see too many error messages.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:44 +0000 (12:39 +0900)]
tools/genboardscfg.py: be tolerant of insane Kconfig
The tools/genboardscfg.py expects all the Kconfig and defconfig are
written correctly. Imagine someone accidentally has broken a board.
Error-out just for one broken board is annoying for the other
developers. Let the tool skip insane boards and continue processing.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:43 +0000 (12:39 +0900)]
tools/genboardscfg.py: be tolerant of missing MAINTAINERS
tools/genboardscfg.py expects all the boards have MAINTAINERS.
If someone adds a new board but misses to add its MAINTAINERS file,
tools/genboardscfg.py fails to generate the boards.cfg file.
It is annoying for the other developers.
This commit allows tools/genboardscfg.py to display warning messages
and continue processing even if some MAINTAINERS files are missing
or have broken formats.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Aug 2014 03:39:42 +0000 (12:39 +0900)]
tools/genboardscfg.py: ignore defconfigs starting with a dot
Kconfig in U-Boot creates a temporary file configs/.tmp_defconfig
during processing "make <board>_defconfig". The temporary file
might be left over for some reasons.
Just in case, tools/genboardscfg.py should make sure to
not read such garbage files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 22 Aug 2014 20:26:43 +0000 (14:26 -0600)]
Fix test failure caused by bad handling of ramdisk
Commit e3a5bbce broke the FIT image tests by not loading a ramdisk even if
a load address is provided in the FIT. The rationale was that a load address
of 0 should be considered to mean 'do not load'.
Add a new load operation which supports this feature, so that the ramdisk
will be loaded if a non-zero load address is provided.
Masahiro Yamada [Fri, 22 Aug 2014 10:42:28 +0000 (19:42 +0900)]
scripts: refetch scripts/setlocalversion from Linux 3.16
Now we have CONFIG_LOCALVERSION and CONFIG_LOCALVERSION_AUTO
in Kconfig so we can use scripts/setlocalversion without
any adjustment. Copy it from Linux 3.16 as is.
Masahiro Yamada [Fri, 22 Aug 2014 05:33:41 +0000 (14:33 +0900)]
buildman: run genboardscfg.py all the time
This commit makes sure boards.cfg is up to date before starting
the build tests. tools/genboardscfg.py exits immediately printing
"boards.cfg is up to date. Nothing to do." when boards.cfg is
already new.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Fri, 22 Aug 2014 05:33:40 +0000 (14:33 +0900)]
MAKEALL: run genboardscfg.py all the time
This commit makes sure boards.cfg is up to date before starting
the build tests. tools/genboardscfg.py exits immediately printing
"boards.cfg is up to date. Nothing to do." when boards.cfg is
already new.
Masahiro Yamada [Fri, 22 Aug 2014 05:10:43 +0000 (14:10 +0900)]
tools/genboardscfg.py: fix a bug of MAINTAINERS handling
This patch fixes a minor problem:
If a block without "F: configs/*_defconfig" is followed by another
block with "F: configs/*_defconfig", the maintainers from the
former block are squashed into the latter.
Łukasz Majewski [Fri, 22 Aug 2014 07:12:58 +0000 (09:12 +0200)]
samsung: s5p_goni: fix: Add missing definitions for G_DNL_UMS gadget
The commit (SHA1: 8fc171318e352) reintroduced correct values for vendor and
product IDs required for UMS gadget to work properly either at Windows or
Linux.
This data was missing for GONI target, so this commit corrects this mistake.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Heiko Schocher [Tue, 24 Jun 2014 08:10:03 +0000 (10:10 +0200)]
lib, linux: move linux specific defines to linux/compat.h
- move linux specific defines from usb and video code
into linux/compat.h
- move common linux specific defines from include/ubi_uboot.h
to linux/compat.h
- add for new mtd/ubi/ubifs sync new needed linux specific
defines to linux/compat.h
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
[trini: Add spin_lock_irqsave/spin_unlock_irqrestore dummies from
usb/lin_gadet_compat.h] Signed-off-by: Tom Rini <trini@ti.com>
Just copied the files from Linux, and added in the c-file
the "#define __UBOOT__" for adding U-Boot special code. In
this case we use this just for adding including U-Boot
headers.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Sergey Lapin <slapin@ossfans.org> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Sergey Lapin <slapin@ossfans.org> Cc: Scott Wood <scottwood@freescale.com> Cc: Tom Rini <trini@ti.com>
Vasili Galka [Thu, 14 Aug 2014 14:42:05 +0000 (17:42 +0300)]
nios2: Fix printf size_t format related warnings (again...)
When compiling the current code on GCC 4.8.3, the following warnings
appear:
warning: format '%zu' expects argument of type 'size_t', but argument
2 has type 'long unsigned int' [-Wformat=]
There were many mails about such warnings on different architectures.
This patch limits itself to the nios2 architecture.
The problem is that for the size_t (%zu, %zd, ...) arguments of
printf GCC does not verify the type match to size_t type. It verifies
the type match to the compiler-defined __SIZE_TYPE__ type. Thus, if
size_t is defined different from __SIZE_TYPE__ - warnings inevitably
appear.
There is a comment by Thomas Chou to the (rejected) patch:
http://patchwork.ozlabs.org/patch/272102/
which explains that the older GCC toolchains (gcc-3.4.6 and gcc-4.1.2)
expect size_t to be "unsigned long" and the newer expect it to be
"unsigned int". Thus, no matter how we define size_t - either way
warnings appear when using some GCC version.
By rejecting that patch, a choice was made to prefer older GCC versions
and leave the warnings when building with the newer toolchains.
Personally, I disagree with this choice...
In any case, this patch proposes a way to fix the warnings for any GCC
version. Just define size_t using the __SIZE_TYPE__ compiler-defined
type and the type verification will pass.
I tested that this fixes the warning on GCC 4.8.3. I don't have an
older toolchain to test with, but __SIZE_TYPE__ was definitely defined
in GCC 3.4.6, so it should work there too.
Signed-off-by: Vasili Galka <vvv444@gmail.com> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Masahiro Yamada [Thu, 21 Aug 2014 02:44:34 +0000 (11:44 +0900)]
kconfig: convert Kconfig helper script into a shell script
Commit 51148790 added scripts/multiconfig.py written in Python 2
to adjust Kconfig for U-Boot.
It has been hard for Python 3 users because Python 2 and Python 3
are not compatible with each other.
We are not happy about adding a new host tool dependency
(in this case, Python version dependency) for the core build process.
After some discussion, we decided to use only basic tools.
The script may get a bit more unreadable by shell scripting,
but we believe it is worthwhile.
In addition, this commit revives "<board>_config" target that is
equivalent to "<board>_defconfig" for backwards compatibility.
It is annoying to adjust various projects which use U-Boot.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Stephen Warren <swarren@nvidia.com>
Roger Meier [Wed, 20 Aug 2014 20:10:29 +0000 (22:10 +0200)]
Makefile: remove generated boards.cfg within make distclean
Signed-off-by: Roger Meier <roger@bufferoverflow.ch> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org>
Thierry Reding [Tue, 19 Aug 2014 08:21:24 +0000 (10:21 +0200)]
net: More BOOTP retry timeout improvements
It's not unusual for DHCP servers to take a couple hundred milliseconds
to respond to DHCP discover messages. One possible reason for the delay
can be that the server checks (typically using an ARP request) that the
IP it's about to hand out isn't in use yet. To make matters worse, some
servers may also queue up requests and process them sequentially, which
can cause excessively long delays if clients retry too fast.
Commit f59be6e850b3 ("net: BOOTP retry timeout improvements") shortened
the retry timeouts significantly, but the BOOTP/DHCP implementation in
U-Boot doesn't handle that well because it will ignore incoming replies
to earlier requests. In one particular setup this increases the time it
takes to obtain a DHCP lease from 630 ms to 8313 ms.
This commit attempts to fix this in two ways. First it increases the
initial retry timeout from 10 ms to 250 ms to give DHCP servers some
more time to respond. At the same time a cache of outstanding DHCP
request IDs is kept so that the implementation will know to continue
transactions even after a retransmission of the DISCOVER message. The
maximum retry timeout is also increased from 1 second to 2 seconds. An
ID cache of size 4 will keep DHCP requests around for 8 seconds (once
the maximum retry timeout has been reached) before dropping them. This
should give servers plenty of time to respond. If it ever turns out
that this isn't enough, the size of the cache can easily be increased.
With this commit the DHCP lease on the above-mentioned setup still takes
longer (1230 ms) than originally, but that's an acceptable compromise to
improve DHCP lease acquisition time for a broader range of setups.
To make it easier to benchmark DHCP in the future, this commit also adds
the time it took to obtain a lease to the final "DHCP client bound to
address x.x.x.x" message.
Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Bryan Wu [Fri, 15 Aug 2014 23:51:38 +0000 (16:51 -0700)]
image: fix bootm failure for FIT image
Commit b3dd64f5d537 "bootm: use genimg_get_kernel_addr()" introduced
a bug for booting FIT image. It's because calling fit_parse_config()
twice will give us wrong value in img_addr.
Add a new function genimg_get_kernel_addr_fit() whichl will always
return fit_uname_config and fit_uname_kernel for CONFIG_FIT.
genimg_get_kernel_addr() will ignore those to parameters.
Reported-by: York Sun <yorksun@freescale.com> Signed-off-by: Bryan Wu <pengw@nvidia.com>
Masahiro Yamada [Fri, 15 Aug 2014 17:50:12 +0000 (02:50 +0900)]
kconfig: remove DEFCONFIG_LIST
CONFIG_DEFCONFIG_LIST specifies the default defconfig.
It is used by "make savedefconfig" when .config is missing.
But that's it. I could not find other useful cases.
As a side effect, CONFIG_DEFCONFIG_LIST="configs/sandbox_defconfig"
is contained in .config of every target board, which some people
think is odd. So, let's remove it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
Vasili Galka [Thu, 14 Aug 2014 09:40:55 +0000 (12:40 +0300)]
Makefile: Use Kbuild style for system_map.o generation step
The command generating the "common/system_map.o" file was always shown
during the build making the output messy. Now it is called using the
Kbuild "cmd" macro, so that the full command is shown only when
building in verbose mode.
Colin Cross [Tue, 12 Aug 2014 17:59:27 +0000 (10:59 -0700)]
add header for Android sparse image format
Add a BSD-3 relicensed version of the Android sparse format image
header from:
https://android.googlesource.com/platform/system/core/+/28fa5bc347390480fe190294c6c385b6a9f0d68b/libsparse/sparse_format.h
Unchanged except for the license header.
Cc: Tom Rini <trini@ti.com> Signed-off-by: Colin Cross <ccross@android.com>
Masahiro Yamada [Wed, 6 Aug 2014 04:42:34 +0000 (13:42 +0900)]
tools/genboardscfg.py: Do not output SPLCPU field
Prior to Kconfig, the CPU field of boards.cfg could optionally have
":SPLCPU", like "armv7:arm720t".
(Actually this syntax was only used for Tegra platform.)
Now it is not necessary at all because CPU is defined by
CONFIG_SYS_CPU in Kconfig.
For Tegra platform, the Kconfig option is described as follows:
config SYS_CPU
string
default "arm720t" if SPL_BUILD
default "armv7" if !SPL_BUILD
Masahiro Yamada [Tue, 5 Aug 2014 06:56:43 +0000 (15:56 +0900)]
kbuild: move extra gcc checks to scripts/Makefile.extrawarn
This commit was imported from Linux Kernel:
commit a86fe353 written by me.
W=... provides extra gcc checks.
Having such code in scripts/Makefile.build results in the same flags
being added to KBUILD_CFLAGS multiple times becuase
scripts/Makefile.build is invoked every time Kbuild descends into
the subdirectories.
Since the top Makefile is already too cluttered, this commit moves
all of extra gcc check stuff to a new file scripts/Makefile.extrawarn,
which is included from the top Makefile.
Masahiro Yamada [Fri, 15 Aug 2014 15:59:26 +0000 (00:59 +0900)]
tools, scripts: refactor error-out statements of Python scripts
In Python, sys.exit() function can also take an object other
than an integer.
If an integer is given to the argument, Python exits with the return
code of it. If a non-integer argument is given, Python outputs it
to stderr and exits with the return code of 1.
That means,
print >> sys.stderr, "Blah Blah"
sys.exit(1)
is equivalent to
sys.exit("Blah Blah")
The latter is a useful shorthand.
Note:
Some error messages in Buildman and Patman were output to stdout.
But they should go to stderr. They are also fixed by this commit.
This is a nice side effect.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
Shaohui Xie [Wed, 13 Aug 2014 10:19:15 +0000 (18:19 +0800)]
powerpc/T4240QDS/eth: some fix for XFI
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
km-powerpc: define CONFIG_PRAM to protect PHRAM and PNVRAM
When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.
This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
powerpc/mpc85xx: Enabling CPC conditionally based on hwconfig options
If hwconfig does not contains "en_cpc" then by default all cpcs are enabled
If this config is defined then only those individual cpcs which are defined
in the subargument of "en_cpc" will be enabled e.g en_cpc:cpc1,cpc2; (this
will enable cpc1 and cpc2) or en_cpc:cpc2; (this enables just cpc2)
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Lukasz Majewski [Mon, 18 Aug 2014 10:12:27 +0000 (12:12 +0200)]
test: dfu: cosmetic: Add missing license information to DFU test scripts
By mistake I've forgotten to add the SPDX license tags for the DFU testing
scripts.
This commit fixes that and also provides some other relevant information.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Stephen Warren <swarren@nvidia.com>
Tim Harvey [Fri, 8 Aug 2014 05:35:45 +0000 (22:35 -0700)]
imx: ventana: add econfig command
The Gateworks Ventana EEPROM contains a set of configuration bits that
affect the removal of device-tree nodes that support peripherals that do not
exist on sub-loaded boards. This patch adds:
- a structure to define a config bit name, dt node alias, bit position
- an array of supported configuration items
- an econfig command to get/set/list configuration bits
- use of the array when adjusting the FDT prior to boot
Tim Harvey [Fri, 8 Aug 2014 05:35:48 +0000 (22:35 -0700)]
imx: ventana: configure i2c_dis# pin properly for gw53xx
The i2c_dis# pinmux/padconf was missing for the GW53xx (this feature was
added to the GW53xx on revB PCB's). Additionally, remove the duplicate
config for GW54xx.
Tim Harvey [Fri, 8 Aug 2014 05:35:41 +0000 (22:35 -0700)]
imx: ventana: set dynamic env var for flash layout
NAND devices have differing layouts with respect to page size and pages per
block. These parameters affect the parameters that need to be passed to
mkfs.ubifs and ubinize used to create UBI images. The various NAND chips
supported by Gateworks Ventana fall into two different layouts which we
refer to as 'normal' and 'large'. This layout is useful when referencing
ubi files to download and flash so we create a dynamic env variable for it.
Tim Harvey [Fri, 8 Aug 2014 05:57:29 +0000 (22:57 -0700)]
pci: mx6: fix occasional link failures
According to the IMX6 reference manuals, REF_SSP_EN (Reference clock enable
for SS function) must remain deasserted until the reference clock is running
at the appropriate frequency.
Without this patch we find a high link failure rate (>5%) on certain
IMX6 boards at various temperatures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Marek Vasut [Sun, 3 Aug 2014 23:47:10 +0000 (01:47 +0200)]
ARM: mx6: Handle the MMDCx_MDCTL COL field caprices
The COL field value cannot be easily calculated from the desired
column number. Instead, there are special cases for that, see the
datasheet, MMDCx_MDCTL field description, field COL . Cater for
those special cases.
Marek Vasut [Sun, 3 Aug 2014 23:47:09 +0000 (01:47 +0200)]
ARM: mx6: Prevent overflow in DRAM size detection
The MX6 DRAM controller can be configured to handle 4GiB of DRAM, but
only 3840 MiB of that can be really used. In case the controller is
configured to operate a 4GiB module, the imx_ddr_size() function will
correctly compute that there is 4GiB of DRAM in the system. Firstly,
the return value is 32-bit, so the function will effectively return
zero. Secondly, the MX6 cannot address the full 4GiB, but only 3840MiB
of all that. Thus, clamp the returned size to 3840MiB in such case.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
Gabriel Huau [Sat, 26 Jul 2014 18:35:43 +0000 (11:35 -0700)]
mx6: add support of multi-processor command
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr> Acked-by: Stefano Babic <sbabic@denx.de>
projects / karo-tx-uboot.git / log