karo-tx-uboot.git
7 years agousb: ehci: fully align interrupt QHs/QTDs
Stephen Warren [Thu, 6 Feb 2014 20:13:06 +0000 (13:13 -0700)]
usb: ehci: fully align interrupt QHs/QTDs

These data structures are passed to cache-flushing routines, and hence
must be conform to both the USB the cache-flusing alignment requirements.
That means aligning to USB_DMA_MINALIGN. This is important on systems
where cache lines are >32 bytes.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
7 years agoush: ehci: initialize altnext pointers in QH
Stephen Warren [Fri, 7 Feb 2014 16:53:50 +0000 (09:53 -0700)]
ush: ehci: initialize altnext pointers in QH

Section 4.10.2 "Advance Queue" of ehci-specification-for-usb.pdf
specifies how an EHCI controller loads a new QTD for processing if the
QH is not already marked as active. It states:

=====
If the field Bytes to Transfer is not zero and the T-bit in the Alternate
Next qTD Pointer is set to zero, then the host controller uses the
Alternate Next qTD Pointer. Otherwise, the host controller uses the Next
qTD Pointer. If Next qTD Pointer’s T-bit is set to a one, then the host
controller exits this state and uses the horizontal pointer to the next
schedule data structure.
=====

Hence, we must ensure that the alternate next QTD pointer's T-bit
(TERMINATE) is set, so the EHCI controller knows to use the next QTD
pointer.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Sat, 8 Mar 2014 01:54:22 +0000 (20:54 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

7 years agopowerpc/t104xrdb: Update DDR initialization related settings
Priyanka Jain [Wed, 26 Feb 2014 04:08:37 +0000 (09:38 +0530)]
powerpc/t104xrdb: Update DDR initialization related settings

Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/t1040qds: Add Video - HDMI support
Priyanka Jain [Wed, 26 Feb 2014 10:41:53 +0000 (16:11 +0530)]
powerpc/t1040qds: Add Video - HDMI support

T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder

Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040
Priyanka Jain [Thu, 30 Jan 2014 10:09:58 +0000 (15:39 +0530)]
powerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040

T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.

Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/t2080rdb: Add T2080PCIe-RDB board support
Shengzhou Liu [Wed, 5 Mar 2014 07:04:48 +0000 (15:04 +0800)]
powerpc/t2080rdb: Add T2080PCIe-RDB board support

T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.

T2080PCIe-RDB Feature Overview
------------------------------
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP devices
 - 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
 - Two 10M/100M/1G RGMII ports on-board
 - Two 10Gbps SFP+ ports on-board
 - Two 10Gbps Base-T ports on-board
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
 - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
 - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
 - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
 - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
 - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
 - SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
 - NOR:  128MB 16-bit NOR flash
 - NAND: 512MB 8-bit NAND flash
 - CPLD: for system controlling with programable header on-board
eSPI:
 - 64MB N25Q512 SPI flash
USB:
 - Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
 - One PCIe x4 gold-finger
 - One PCIe x4 connector
 - One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
 - Two SATA 2.0 ports on-board
SDHC:
 - support a TF-card on-board
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/t208xqds: fixup for t208xqds
Shengzhou Liu [Thu, 6 Mar 2014 07:07:39 +0000 (15:07 +0800)]
powerpc/t208xqds: fixup for t208xqds

Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0.
Fix EMI2 for t2080qds, which was caused by adding t2081qds.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agobootstage: powerpc: support fdt stash and reporting
Mela Custodio [Wed, 19 Feb 2014 15:16:57 +0000 (00:16 +0900)]
bootstage: powerpc: support fdt stash and reporting

This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.

Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/usb: Workaround for erratum-A006261
Suresh Gupta [Wed, 26 Feb 2014 08:59:12 +0000 (14:29 +0530)]
powerpc/usb: Workaround for erratum-A006261

USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agopowerpc/b4860: Add workaround for errata A006384 and A006475
Shaveta Leekha [Wed, 26 Feb 2014 10:38:22 +0000 (16:08 +0530)]
powerpc/b4860: Add workaround for errata A006384 and A006475

SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration

Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agoB4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to work
Shaveta Leekha [Wed, 26 Feb 2014 10:37:51 +0000 (16:07 +0530)]
B4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to work

Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agoB4860/B4420: Add PLL_NUM define for B4420/B4860 to use SerDes2 Refclks re-configuration
Shaveta Leekha [Wed, 26 Feb 2014 10:37:37 +0000 (16:07 +0530)]
B4860/B4420: Add PLL_NUM define for B4420/B4860 to use SerDes2 Refclks re-configuration

B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes,
add their defines in arch/powerpc/include/asm/config_mpc85xx.h

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years ago85xx/b4860: Alternate serdes protocols for B4860/B4420
poonam aggrwal [Mon, 17 Feb 2014 03:08:58 +0000 (08:38 +0530)]
85xx/b4860: Alternate serdes protocols for B4860/B4420

On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.

Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.

The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agoboard/b4860qds: Add support to make PCIe SATA work on B4860QDS
Shaveta Leekha [Wed, 26 Feb 2014 10:36:56 +0000 (16:06 +0530)]
board/b4860qds: Add support to make PCIe SATA work on B4860QDS

1) SerDes2 Refclks have been set properly to make
     PCIe SATA to work as it work on SerDes refclk of 100MHz
  2) Mask the SerDes's device reset request before changing
     the Refclks for SerDes1 and SerDes2 for PLL locks to
     happen properly, device reset request bit unmasked
     after SerDes refclks configuration

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agoboard/b4860qds: Add support to make Aurora work on B4860QDS
Shaveta Leekha [Wed, 26 Feb 2014 10:36:30 +0000 (16:06 +0530)]
board/b4860qds: Add support to make Aurora work on B4860QDS

1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
   CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
   lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
   Aurora, CPRI and SGMIIs to work together properly

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
7 years agokbuild: move "checkgcc4" to PowerPC archprepare
Masahiro Yamada [Wed, 5 Mar 2014 08:49:23 +0000 (17:49 +0900)]
kbuild: move "checkgcc4" to PowerPC archprepare

"checkgcc4" is used only for PowerPC.
Move it to arch/powerpc/config.mk.

To make sure gcc is new enough before beginning build,
run "checkgcc4" during "archprepare".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: move "checkthumb" to ARM archprepare
Masahiro Yamada [Wed, 5 Mar 2014 08:49:22 +0000 (17:49 +0900)]
kbuild: move "checkthumb" to ARM archprepare

"checkthumb" makes sense only for ARM architecture.
Move it to arch/arm/config.mk.

To make sure gcc supports THUMB mode before beginning build,
run "checkthumb" during "archprepare".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agopowerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260
Masahiro Yamada [Wed, 5 Mar 2014 08:40:10 +0000 (17:40 +0900)]
powerpc: mpc8260: consolidate CONFIG_MPC8260 and CONFIG_8260

Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.

All boards with mpc8260 cpu defined both of them:
  - CONFIG_MPC8260 was defined in board config headers
      and include/common.h
  - CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk

We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.

This commit does:
 - Delete CONFIG_8260 and CONFIG_MPC8260 definition
   in config headers and include/common.h
 - Rename CONFIG_8260 to CONFIG_MPC8260
    in arch/powerpc/cpu/mpc8260/config.mk.
 - Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
7 years agomips: move CONFIG_MIPS{32, 64} definition to config.mk
Masahiro Yamada [Wed, 5 Mar 2014 08:25:37 +0000 (17:25 +0900)]
mips: move CONFIG_MIPS{32, 64} definition to config.mk

All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.

CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
7 years agokbuild: improve Kbuild speed
Masahiro Yamada [Wed, 5 Mar 2014 07:59:40 +0000 (16:59 +0900)]
kbuild: improve Kbuild speed

Kbuild brought about many advantages for us but a significant
performance regression was reported by Simon Glass.

After some discussions and analysis, it turned out
its main cause is in $(call cc-option,...).

Historically, U-Boot parses all config.mk
(arch/*/config.mk and board/*/config.mk)
every time descending into subdirectories.
That means cc-options are evaluated over and over again.

$(call cc-option,...) is useful but costly.
So we want to evaluate them only in ./Makefile
and spl/Makefile and export compiler flags.

This commit changes the build system as follows:

  - Modify scripts/Makefile.build to not include config.mk
    Instead, add $(PLATFORM_CPPFLAGS) to asflags-y, ccflags-y,
    cppflags-y.

  - Export many variables
    Going forward, Kbuild will not parse config.mk files
    when it descends into subdirectories.
    If we want to set variables in config.mk and use them
    in subdirectories, they must be exported.

    This is the list of variables to get exported:
      PLATFORM_CPPFLAGS
      CPUDIR
      BOARDDIR
      OBJCOPYFLAGS
      LDFLAGS
      LDFLAGS_FINAL
        (used in nand_spl/board/*/*/Makefile)
      CONFIG_STANDALONE_LOAD_ADDR
        (used in examples/standalone/Makefile)
      SYM_PREFIX
        (used in examples/standalone/Makefile)
      RELFLAGS
        (used in examples/standalone/Makefile)

  - Delete CPPFLAGS
    This variable has been replaced with PLATFORM_CPPFLAGS

  - Copy gcclibdir from example/standalone/Makefile
    to arch/sparc/config.mk
    The reference in CONFIG_STANDALONE_LOAD_ADDR must be
    resolved before it is exported.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> [on Sandbox]
Tested-by: Stephen Warren <swarren@nvidia.com> [on Tegra]
7 years agoconfig.mk: specify the exact path to standalone linker script
Masahiro Yamada [Wed, 5 Mar 2014 07:59:39 +0000 (16:59 +0900)]
config.mk: specify the exact path to standalone linker script

We want to change the build system to include config.mk
only from ./Makefile and spl/Makefile.
We must prepare for that in this commit.

$(src) is a moving target and not handy for our purpose.
We must replace it with a fixed path.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Masahiro Yamada [Wed, 5 Mar 2014 07:59:38 +0000 (16:59 +0900)]
kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC

Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.

We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.

By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)

Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.

It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding

  #ifdef CONFIG_SPL_BUILD
  # define CONFIG_USE_PRIVATE_LIBGCC
  #endif

to include/configs/tegra-common.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
7 years agokbuild, blackfin: Add CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
Masahiro Yamada [Wed, 5 Mar 2014 07:59:37 +0000 (16:59 +0900)]
kbuild, blackfin: Add CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED

Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.

We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.

CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.

Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
7 years agocmd_nvedit: Make 'env import -c' require size parameter
Tom Rini [Tue, 4 Mar 2014 20:52:35 +0000 (15:52 -0500)]
cmd_nvedit: Make 'env import -c' require size parameter

When importing a checksummed area we need to be told how big the area in
question is so that we know that will match the size of the area which
the checksum is generated against.

Reported-by: Pierre AUBERT <p.aubert@staubli.com>
Signed-off-by: Tom Rini <trini@ti.com>
7 years agoCosmetic: Typo fixes
Vasili Galka [Tue, 4 Mar 2014 15:24:09 +0000 (17:24 +0200)]
Cosmetic: Typo fixes

Signed-off-by: Vasili Galka <vasili@visionmap.com>
7 years agoppc4xx: Remove 4xx NAND booting support
Stefan Roese [Tue, 4 Mar 2014 14:34:35 +0000 (15:34 +0100)]
ppc4xx: Remove 4xx NAND booting support

As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.

This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
7 years agonet/phy: Correct AR8021 phy_mask
Haijun.Zhang [Tue, 4 Mar 2014 07:56:12 +0000 (15:56 +0800)]
net/phy: Correct AR8021 phy_mask

There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
7 years agoxilinx: delete meaningless .gitignore files
Masahiro Yamada [Tue, 4 Mar 2014 02:36:51 +0000 (11:36 +0900)]
xilinx: delete meaningless .gitignore files

config.tmp is never generated

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
7 years agounit-test: make "test -e" test independent of $CWD
Stephen Warren [Sun, 2 Mar 2014 05:18:00 +0000 (22:18 -0700)]
unit-test: make "test -e" test independent of $CWD

The unit-test for hush's "test -e" currently relies upon being run in
the U-Boot build directory, because it tests for the existence of a file
that exists in that directory.

Fix this by explicitly creating the file we use for the existence test,
and deleting it afterwards so that multiple successive unit-test
invocations succeed. This required adding an os.c function to erase
files.

Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
7 years agohush: fix some quoted variable expansion issues
Stephen Warren [Sun, 2 Mar 2014 05:16:10 +0000 (22:16 -0700)]
hush: fix some quoted variable expansion issues

The following shell command fails:

if test -z "$x"; then echo "zero"; else echo "non-zero"; fi

(assuming $x does not exist, it prints "non-zero" rather than "zero").

... since "$x" expands to nothing, and the argument is completely
dropped, causing too few to be passed to -z, causing cmd_test() to
error out early.

This is because when variable expansions are processed by make_string(),
the expanded results are concatenated back into a new string. However,
no quoting is applied when doing so, so any empty variables simply don't
generate any parameter when the combined string is parsed again.

Fix this by explicitly replacing quoting any argument that was originally
quoted when re-generating a string from the already-parsed argument list.

This also fixes loss of whitespace in commands such as:

setenv space " "
setenv var " 1${space}${space} 2 "
echo ">>${var}<<"

Reported-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
7 years agounit-test: clean up evironment after Hush tests
Stephen Warren [Fri, 28 Feb 2014 05:01:28 +0000 (22:01 -0700)]
unit-test: clean up evironment after Hush tests

Delete the temporary variables that are used to save unit-test results
from the environment after running the test. This prevents polluting
the environment, or growing it too much.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
7 years agonet: asix: don't pad odd-length TX packets
Stephen Warren [Thu, 27 Feb 2014 20:27:02 +0000 (13:27 -0700)]
net: asix: don't pad odd-length TX packets

For Ethernet/USB RX packets, the ASIX HW pads odd-sized packets so that
they have an even size. Currently, asix_recv() does remove this padding,
and asic_send() adds equivalent padding in the TX path. However, the HW
does not appear to need this packing for TX packets in practical testing
with "ASIX Elec. Corp. AX88x72A 000001" Vendor: 0x0b95 Product 0x7720
Version 0.1. The Linux kernel does no such padding for the TX path.

Remove the padding from the TX path:

* For consistency with the Linux kernel.
* NVIDIA has a Tegra simulator which validates that the length of USB
  packets sent to an ASIX device matches the packet length value inside
  the packet data. Having U-Boot and the kernel do the same thing when
  creating the TX packets simplifies the simulator's validation.

Cc: Lucas Stach <dev@lynxeye.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Gerhard Sittig <gsi@denx.de>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-nand-flash
Tom Rini [Wed, 5 Mar 2014 02:23:42 +0000 (21:23 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash

7 years agomtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
pekon gupta [Fri, 22 Nov 2013 11:23:30 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand

omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
pekon gupta [Fri, 22 Nov 2013 11:23:29 +0000 (16:53 +0530)]
mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand

omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common...
pekon gupta [Fri, 22 Nov 2013 11:23:28 +0000 (16:53 +0530)]
mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h

Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: remove unused #defines from common omap_gpmc.h
pekon gupta [Fri, 22 Nov 2013 11:23:27 +0000 (16:53 +0530)]
mtd: nand: omap: remove unused #defines from common omap_gpmc.h

OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: remove redundant platform specific header: arch-xx/omap_gpmc.h
pekon gupta [Fri, 22 Nov 2013 11:23:26 +0000 (16:53 +0530)]
mtd: nand: omap: remove redundant platform specific header: arch-xx/omap_gpmc.h

Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
 common header file for all platforms, containing defines and declarations used
 by GPMC NAND driver.

(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
 SoC platform specific header file containing defines like ECC layout.

This patch removes platform specific arch-xx/omap_gpmc.c because:
 - GPMC hardware engine is common for all SoC platforms hence only (a) is enough
 - ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
   selected. Hence all ECC layout declarations in (b) are redundant.

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-mips
Tom Rini [Tue, 4 Mar 2014 23:13:06 +0000 (18:13 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mips

7 years agomalta: correct tcl script path in README.malta
James Hogan [Tue, 4 Mar 2014 14:48:42 +0000 (14:48 +0000)]
malta: correct tcl script path in README.malta

README.malta referred to board/malta, but malta has now been moved
within board/imgtec/, so correct the path.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
7 years agoMIPS: fix types u64 and __u64 to unsigned long long
Daniel Schwierzeck [Tue, 4 Mar 2014 22:01:11 +0000 (23:01 +0100)]
MIPS: fix types u64 and __u64 to unsigned long long

Linux MIPS uses asm-generic/int-ll64.h in asm/types.h.
Thus u64 and __u64 are defined as unsigned long long. Port this
over to U-Boot.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
7 years agoarc: arcangel4: set board entry <none> to fix a build error
Masahiro Yamada [Mon, 3 Mar 2014 10:03:18 +0000 (19:03 +0900)]
arc: arcangel4: set board entry <none> to fix a build error

There are no source files in board/synopsys/arcangel4/
directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
7 years agokbuild: allow empty board directories
Masahiro Yamada [Mon, 3 Mar 2014 10:03:17 +0000 (19:03 +0900)]
kbuild: allow empty board directories

U-Boot has compelled all boards to have
board/${BOARD}/ or board/${VENDOR}/${BOARD}/ directory.

Sometimes it does not seem suitable for some boards,
for example Sandbox. (Is it a board?)

And arcangel4 board has nothing to compile
under the board directory.

This commit makes the build system more flexible:
If '<none>' is given to the 6th column (=Board name) of boards.cfg,
Kbuild will not descend into the board directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: tools: fix a bug that always builds Denx logo
Masahiro Yamada [Mon, 3 Mar 2014 09:40:56 +0000 (18:40 +0900)]
kbuild: tools: fix a bug that always builds Denx logo

LOGO_BMP was never overwritten by board-specific or
vendor-specific logos.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
7 years agokbuild: add "cross_tools" target to build tools for the target
Masahiro Yamada [Mon, 3 Mar 2014 02:06:19 +0000 (11:06 +0900)]
kbuild: add "cross_tools" target to build tools for the target

Programs in tools/ directory are usually built for the host.
But some of them (mkimage, dumpimge, gen_eth_addr, etc.) are
useful on the target OS too.

Actually, prior to Kbuild, U-Boot could build tools for
the target like follows:

  $ make <target_board>_config
  $ export CROSS_COMPILE=<cross_gcc_prefix>
  $ make HOSTCC=${CROSS_COMPILE}gcc HOSTSTRIP=${CROSS_COMPILE}strip tools

In Kbuild, we can no longer replace HOSTCC at the command line.

In order to get back that feature, this commit adds "cross-tools" target.

Usage:

  Build tools for the host
  $ make CROSS_COMPILE=<cross_gcc_prefix> tools

  Build tools for the target
  $ make CROSS_COMPILE=<cross_gcc_prefix> cross_tools

Besides, "make cross_tools" strip tools programs because we
generally expect smaller storages on embedded systems.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
7 years agokbuild: fix "tools-all" target
Masahiro Yamada [Mon, 3 Mar 2014 02:06:18 +0000 (11:06 +0900)]
kbuild: fix "tools-all" target

The top Makefile must export HOST_TOOLS_ALL to use it
in tools/Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
7 years agoboard: config.mk: delete unused sinclude directive
Masahiro Yamada [Fri, 28 Feb 2014 11:12:34 +0000 (20:12 +0900)]
board: config.mk: delete unused sinclude directive

config.tmp is not there.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agoboard: .gitignore: ignore board-specific generated files
Masahiro Yamada [Fri, 28 Feb 2014 10:59:16 +0000 (19:59 +0900)]
board: .gitignore: ignore board-specific generated files

Ignore
  - board/cray/L1/bootscript.{c|image}
  - board/matrix_vision/mvblm7/bootscript.img
  - board/maxtir_vision/mvsmr/bootscript.img

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
7 years agoboard: gaisler: delete unnecessary include path
Masahiro Yamada [Fri, 28 Feb 2014 10:42:26 +0000 (19:42 +0900)]
board: gaisler: delete unnecessary include path

The same outputs are generated with or without -I$(TOPDIR)/board.
I cannot understand why it is necessary. Remove.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
7 years agokbuild: fix CROSS_COMPILE settings in config.mk
Masahiro Yamada [Fri, 28 Feb 2014 05:33:30 +0000 (14:33 +0900)]
kbuild: fix CROSS_COMPILE settings in config.mk

The syntax
  CROSS_COMIPLE ?= <cross_compiler_prefix>
does not work because config.mk is parsed after
exporting CROSS_COMPILE.

Like Linux Kernel's arch/$(ARCH)/Makefile,
we must write as follows:

  ifeq ($(CROSS_COMPILE),)
  CROSS_COMPILE := <cross_compiler_prefix>
  endif

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: consolidate PLATFORM_LIBS
Masahiro Yamada [Thu, 27 Feb 2014 13:40:34 +0000 (22:40 +0900)]
kbuild: consolidate PLATFORM_LIBS

We had switched to Kbuild so now we can specify
PLATFORM_LIBS/PLATFORM_LIBGCC with relative path.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
7 years agoscripts: update checkpatch.pl to latest upstream version
Tom Rini [Thu, 27 Feb 2014 13:27:28 +0000 (08:27 -0500)]
scripts: update checkpatch.pl to latest upstream version

Update to v3.14-rc4's version of checkpatch.pl.  In doing so we drop the
changes to top_of_kernel_tree() as we pass in --no-tree and drop our
changes about MAINTAINERS as that's for reporting checkpatch.pl problems
itself (and upstream has said they'll reword this section to be
clearer).

Signed-off-by: Tom Rini <trini@ti.com>
7 years agoAdd 64-bit data support for memory commands
York Sun [Thu, 27 Feb 2014 01:03:19 +0000 (17:03 -0800)]
Add 64-bit data support for memory commands

Add 64-bit data for memory commands, such as md, mw, mm, cmp. The new
size ".q " is introduced.

For 64-bit architecture, 64-bit data is enabled by default, by detecting
compiler __LP64__. It is optional for other architectures.

Signed-off-by: York Sun <yorksun@freescale.com>
7 years agodm: Remove old driver model documentation
Simon Glass [Wed, 26 Feb 2014 22:59:27 +0000 (15:59 -0700)]
dm: Remove old driver model documentation

This documentation pertains to the planned implementation of driver model
in U-Boot for each subsystem, but it has not been superseded. It is
probably better to have this documentation in the source code for each
subsystem where possible, so that docbook will pick it up. Where this does
not make sense, new documentation can be placed in some suitable file in
doc/driver-model.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agodm: Enable gpio command to support driver model
Simon Glass [Wed, 26 Feb 2014 22:59:26 +0000 (15:59 -0700)]
dm: Enable gpio command to support driver model

Now that named GPIO banks are supported, along with a way of obtaining
the status of a GPIO (input or output), we can provide an enhanced
GPIO command for driver model. Where the driver provides its own operation
for obtaining the GPIO state, this is used, otherwise a generic version
is sufficient.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agosandbox: Convert GPIOs to use driver model
Simon Glass [Wed, 26 Feb 2014 22:59:25 +0000 (15:59 -0700)]
sandbox: Convert GPIOs to use driver model

Convert sandbox over to use driver model GPIOs.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agodm: Add GPIO support and tests
Simon Glass [Wed, 26 Feb 2014 22:59:24 +0000 (15:59 -0700)]
dm: Add GPIO support and tests

Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.

Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.

The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.

Anonymous GPIO banks are also supported, and are just numbered without any
prefix.

Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
7 years agodm: Add a demonstration/example driver
Simon Glass [Wed, 26 Feb 2014 22:59:23 +0000 (15:59 -0700)]
dm: Add a demonstration/example driver

As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.

To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.

The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
7 years agodm: Add a 'dm' command for testing
Simon Glass [Wed, 26 Feb 2014 22:59:22 +0000 (15:59 -0700)]
dm: Add a 'dm' command for testing

This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
7 years agodm: Add basic tests
Simon Glass [Wed, 26 Feb 2014 22:59:21 +0000 (15:59 -0700)]
dm: Add basic tests

Add some tests of driver model functionality. Coverage includes:

- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed

This function is enabled for sandbox, using CONFIG_DM_TEST.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agodm: Set up driver model after relocation
Simon Glass [Wed, 26 Feb 2014 22:59:20 +0000 (15:59 -0700)]
dm: Set up driver model after relocation

Make driver model available after relocation, by setting up data structures
and scanning for devices using compiled-in platform_data and (when available)
the device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agosandbox: config: Enable driver model
Simon Glass [Wed, 26 Feb 2014 22:59:19 +0000 (15:59 -0700)]
sandbox: config: Enable driver model

Use driver model in sandbox to permit running of driver model unit test.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agodm: Add base driver model support
Simon Glass [Wed, 26 Feb 2014 22:59:18 +0000 (15:59 -0700)]
dm: Add base driver model support

Add driver model functionality for generic board.

This includes data structures and base code for registering devices and
uclasses (groups of devices with the same purpose, e.g. all I2C ports will
be in the same uclass).

The feature is enabled with CONFIG_DM.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
7 years agodm: Add README for driver model
Simon Glass [Wed, 26 Feb 2014 22:59:17 +0000 (15:59 -0700)]
dm: Add README for driver model

This adds a README to help with understanding of this series.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agoyaffs: Remove private list implementation
Simon Glass [Wed, 26 Feb 2014 22:59:16 +0000 (15:59 -0700)]
yaffs: Remove private list implementation

U-Boot already has a list implementation, and files which include both
that and the yaffs implementation will get errors:

In file included from ydirectenv.h:80:0,
                 from yportenv.h:81,
                 from yaffs_guts.h:19,
                 from yaffs_allocator.h:19,
                 from yaffs_allocator.c:14:
yaffs_list.h:32:8: error: redefinition of ‘struct list_head’
 struct list_head {
        ^

Remove the yaffs implementation.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agoAdd cmd_process_error() to report and process errors
Simon Glass [Wed, 26 Feb 2014 22:59:15 +0000 (15:59 -0700)]
Add cmd_process_error() to report and process errors

U-Boot now uses errors defined in include/errno.h which are negative
integers. Commands which fail need to report the error and return 1
to indicate failure. Add this functionality in cmd_process_error().

For now this merely reports the error number. It would be possible
also to produce a helpful error message by storing the error strings
in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agosandbox: Build a device tree file for sandbox
Simon Glass [Wed, 26 Feb 2014 22:59:14 +0000 (15:59 -0700)]
sandbox: Build a device tree file for sandbox

Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE
option to make it easier to use device tree with sandbox.

This adjusts the Makefile to build a u-boot.dtb file which can be passed
to sandbox U-Boot with:

   ./u-boot -d u-boot.dtb

Signed-off-by: Simon Glass <sjg@chromium.org>
7 years agosizes.h - consolidate for all architectures
Alexey Brodkin [Wed, 26 Feb 2014 13:47:58 +0000 (17:47 +0400)]
sizes.h - consolidate for all architectures

Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
7 years agonand_spl: display warning message to inform the end of nand_spl
Masahiro Yamada [Wed, 26 Feb 2014 08:51:11 +0000 (17:51 +0900)]
nand_spl: display warning message to inform the end of nand_spl

Now we have two different frameworks for doing the same thing.
I'd like to propose to drop nand_spl framework.
How about deleting it before v2014.07 release?

In the interim, this commit will display a warning message
when compiling nand_spl board.

Now we have 19 nand_spl boards:

  MPC8315ERDB_NAND
  SIMPC8313_LP
  SIMPC8313_SP
  MPC8536DS_NAND
  MPC8569MDS_NAND
  MPC8572DS_NAND
  P1023RDS_NAND
  P1011RDB_NAND
  P1020RDB_NAND
  P2010RDB_NAND
  P2020RDB_NAND
  acadia_nand
  bamboo_nand
  canyonlands_nand
  glacier_nand
  haleakala_nand
  kilauea_nand
  rainier_nand
  sequoia_nand

They must be ported to SPL before the deadline,
otherwise they will be removed.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
7 years agom68k: merge compile flags -ffixed-d7 -sep-data
Masahiro Yamada [Wed, 26 Feb 2014 05:51:04 +0000 (14:51 +0900)]
m68k: merge compile flags -ffixed-d7 -sep-data

All arch/m68k/cpu/*/config.mk define the same flags
  PLAGFORM_REFLFLAGS += -ffixed-d7 -msep-data
Move it to arch/m68k/config.mk

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
7 years agosh: merge compiler flag -ffixed-r13
Masahiro Yamada [Wed, 26 Feb 2014 05:51:03 +0000 (14:51 +0900)]
sh: merge compiler flag -ffixed-r13

-ffixed-r13 is defined commonly for sh2, sh3, sh4.
Move it to arch/sh/config.mk

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
7 years agosh: Do not define -ffreestanding twice
Masahiro Yamada [Wed, 26 Feb 2014 05:51:02 +0000 (14:51 +0900)]
sh: Do not define -ffreestanding twice

-ffreestanding is defined at the top Makefile for all architectures.
Do not define it twice for SH2A.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
7 years agox86: Delete redundant compiler flags
Masahiro Yamada [Wed, 26 Feb 2014 05:51:01 +0000 (14:51 +0900)]
x86: Delete redundant compiler flags

-Wstrict-prototypes, -ffreestanding, -fno-stack-protector
are defined at the top Makefile for all architectures.

Do not define them twice for x86.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
7 years agonand_spl: simpc8313: move config.mk used only for nand_spl
Masahiro Yamada [Wed, 26 Feb 2014 05:51:00 +0000 (14:51 +0900)]
nand_spl: simpc8313: move config.mk used only for nand_spl

board/sheldon/simpc8313/config.mk is used only for nand_spl.
So it should go into nand_spl/board/sheldon/simpc8313/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agoMakefile: delete unused variable LDSCRIPT_MAKEFILE_DIR
Masahiro Yamada [Wed, 26 Feb 2014 05:50:59 +0000 (14:50 +0900)]
Makefile: delete unused variable LDSCRIPT_MAKEFILE_DIR

LDSCRIPT_MAKEFILE_DIR is not referenced from anywhere. Remove.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agoconfig.mk: Delete unused variable BCURDIR
Masahiro Yamada [Wed, 26 Feb 2014 05:50:58 +0000 (14:50 +0900)]
config.mk: Delete unused variable BCURDIR

This variable was abolished by Kbuild series.
I forgot to delete it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: post: fix dependency tracking correctly
Masahiro Yamada [Wed, 26 Feb 2014 02:26:08 +0000 (11:26 +0900)]
kbuild: post: fix dependency tracking correctly

$(call if_changed,...) must take FORCE as a prerequite.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
7 years agoserial: zynq: Add OF initialization support
Michal Simek [Mon, 24 Feb 2014 10:16:33 +0000 (11:16 +0100)]
serial: zynq: Add OF initialization support

Add console selection from DTB which is enough to have
OF driven solution.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agozynq: Add OF ram initialization support
Michal Simek [Mon, 24 Feb 2014 10:16:32 +0000 (11:16 +0100)]
zynq: Add OF ram initialization support

Read ram size directly from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agommc: zynq: Add OF initialization support
Michal Simek [Mon, 24 Feb 2014 10:16:31 +0000 (11:16 +0100)]
mmc: zynq: Add OF initialization support

Enable initialize sdhci from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agonet: gem: Add OF initialization support
Michal Simek [Mon, 24 Feb 2014 10:16:30 +0000 (11:16 +0100)]
net: gem: Add OF initialization support

Gem can be directly initialized from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agozynq: Do not use SPL OF initialization
Michal Simek [Mon, 24 Feb 2014 10:16:29 +0000 (11:16 +0100)]
zynq: Do not use SPL OF initialization

Disable CONFIG_OF_CONTROL for SPL compilation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agonet: emaclite: Fix OF initialization
Michal Simek [Mon, 24 Feb 2014 10:16:28 +0000 (11:16 +0100)]
net: emaclite: Fix OF initialization

- Add xilinx_emaclite_of_init to netdev.h
- Remove global data pointer from the driver
- Add better handling for error state.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
7 years agoboard/ti/am335x/README: update for NAND boot
pekon gupta [Tue, 19 Nov 2013 05:32:18 +0000 (11:02 +0530)]
board/ti/am335x/README: update for NAND boot

NAND boot mode on AM335x EVM has been verified, and steps
to use it has been documented and update in this README

Signed-off-by: Pekon Gupta <pekon@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Tom Rini <trini@ti.com>
7 years agomtd: nand: omap: optimized chip->ecc.correct() for H/W ECC schemes
pekon gupta [Tue, 19 Nov 2013 05:32:17 +0000 (11:02 +0530)]
mtd: nand: omap: optimized chip->ecc.correct() for H/W ECC schemes

chip->ecc.correct() is used for detecting and correcting bit-flips during read
operations. In omap-nand driver it implemented as:
(a) omap_correct_data(): for h/w based ECC_HAM1 scheme
(b) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
for ECC_BCH8 scheme using GPMC and software lib/bch.c
(c) omap_correct_data_bch() + CONFIG_NAND_OMAP_ECC_BCH8_CODE_HW
for ECC_BCH8 scheme using GPMC and ELM

This patch updates (c)
- checks for calc_ecc[]==0x00 so that error_correction is not required for
  known good pages.
- adds scalability for other ECC_BCHx scheme by merging following
  omap_rotate_ecc_bch() + omap_fix_errors_bch() => omap_correct_data_bch()
- fixing logic for bit-flip correction based on error_loc[count]

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: optimize chip->ecc.calculate() for H/W ECC schemes
pekon gupta [Tue, 19 Nov 2013 05:32:16 +0000 (11:02 +0530)]
mtd: nand: omap: optimize chip->ecc.calculate() for H/W ECC schemes

chip->ecc.calculate() is used for calculating and fetching of ECC syndrome by
processing the data passed during Read/Write accesses.

All H/W based ECC schemes use GPMC controller to calculate ECC syndrome.
But each BCHx_ECC scheme has its own implemetation of post-processing and
fetching ECC syndrome from GPMC controller.

This patch updates OMAP_ECC_BCH8_CODE_HW ECC scheme in following way:
- merges multiple chip->calculate API for different ECC schemes
  omap_calculate_ecc() + omap_calculate_ecc_bch() + omap_calculate_ecc_bch_sw()
==> omap_calculate_ecc()
- removes omap_ecc_disable() and instead uses it as inline.

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agomtd: nand: omap: optimize chip->ecc.hwctl() for H/W ECC schemes
pekon gupta [Tue, 19 Nov 2013 05:32:15 +0000 (11:02 +0530)]
mtd: nand: omap: optimize chip->ecc.hwctl() for H/W ECC schemes

chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)

Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()

(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()

Signed-off-by: Pekon Gupta <pekon@ti.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Wed, 26 Feb 2014 21:49:58 +0000 (16:49 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
arch/arm/cpu/armv7/config.mk
board/ti/am43xx/mux.c
include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
7 years agoarm: Switch to -mno-unaligned-access when supported by the compiler
Tom Rini [Tue, 25 Feb 2014 15:27:01 +0000 (10:27 -0500)]
arm: Switch to -mno-unaligned-access when supported by the compiler

When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level.  We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.

To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@ti.com>
7 years agocheckpatch.pl: Add warning for new __packed additions
Tom Rini [Tue, 25 Feb 2014 15:27:00 +0000 (10:27 -0500)]
checkpatch.pl: Add warning for new __packed additions

While there are valid reasons to use __packed, often the answer is that
you should be doing something else here instead.

Signed-off-by: Tom Rini <trini@ti.com>
7 years agoarm: remove unneeded symbol offsets and _TEXT_BASE
Albert ARIBAUD [Sat, 22 Feb 2014 16:53:43 +0000 (17:53 +0100)]
arm: remove unneeded symbol offsets and _TEXT_BASE

Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
7 years agoarm: make _end compiler-generated
Albert ARIBAUD [Sat, 22 Feb 2014 16:53:42 +0000 (17:53 +0100)]
arm: make _end compiler-generated

This prevents references to _end from generating absolute
relocation records.

This change is binary invariant for ARM targets.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
7 years agocm_t335: fix linker file to produce full ELF
Albert ARIBAUD [Sat, 22 Feb 2014 16:53:41 +0000 (17:53 +0100)]
cm_t335: fix linker file to produce full ELF

Newly added cm_t335 was missed in commit 47ed5dd0 which
made ARM targets produce full ELF files. Fix its linker
script.

This change is binary-invariant when only .dynsym, .dynstr,
.dynamic, .plt, .interp and .gun sections are declared.

Sections .hash, .got.plt, .dynbss and .ARM.exidx are also
declared so that their (unused) content is moved out of the
u-boot binary.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
7 years agoRevert "ext4fs: Add ext4 extent cache for read operations"
Tom Rini [Wed, 26 Feb 2014 13:18:58 +0000 (08:18 -0500)]
Revert "ext4fs: Add ext4 extent cache for read operations"

This reverts commit fc0fc50f38a4d7d0554558076a79dfe8b0d78cd5.

The author has asked on the mailing list that we revert this for now as
it breaks write support.

Reported-by: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
7 years agoMerge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Tue, 25 Feb 2014 17:44:13 +0000 (12:44 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
7 years agoarm: omap: delete unincluded omap-common/config.mk
Masahiro Yamada [Tue, 25 Feb 2014 01:01:50 +0000 (10:01 +0900)]
arm: omap: delete unincluded omap-common/config.mk

arch/arm/cpu/armv7/omap-common/config.mk is never included
because "omap-common" is not SoC name.

If we want to add OMAP-specific compiler flags,
they must be added to omap3/config.mk, omap4/config.mk, omap5/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
7 years agokbuild: Move linker sciript check to prepare1
Masahiro Yamada [Tue, 25 Feb 2014 10:26:48 +0000 (19:26 +0900)]
kbuild: Move linker sciript check to prepare1

Same as the previous commit.
Move sanity check to prepare1 target to avoid nasty troubles.

Before this commit, LDSCRIPT existence was not checked
when it was specified by CONFIG_SYS_LDSCRIPT.
Now LDSCRIPT existence is checked for all boards.

$(wildcard $(LDSCRIPT)) must point to the linker scripts
with absolute path.
Otherwise, make will terminate with a false error
on out-of-tree build.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: Fix a false error of generic board support
Masahiro Yamada [Tue, 25 Feb 2014 10:26:47 +0000 (19:26 +0900)]
kbuild: Fix a false error of generic board support

Before this commit, make terminated with an error
where is shouldn't under some condition.

This bug happened when we built a board unsupporting
generic board right after building with generic board.

For example, the following sequence failed.
(harmony uses generic board but microblaze-generic does not
support it)

  $ make harmony_config
  Configuring for harmony board...
  $ make CROSS_COMPILE=arm-linux-gnueabi-
    [ Build succeed ]
  $ make microblaze-generic_config
  Configuring for microblaze-generic board...
  $ make CROSS_COMPILE=microblaze-linux-
  Makefile:488: *** Your architecture does not support generic board.
  Please undefined CONFIG_SYS_GENERIC_BOARD in your board config file.  Stop.

We had to do "make clean" before building the microblaze board.

This commit fixes this unconvenience.

Move generic board sanity check to "prepare1" target,
which is run after generation of include/autoconf.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
7 years agokbuild: get back DTB at the top directory
Masahiro Yamada [Fri, 21 Feb 2014 06:34:30 +0000 (15:34 +0900)]
kbuild: get back DTB at the top directory

Commit 6ab6b2af deleted ./u-boot.dtb because it was a copy
of dts/dt.dtb.

But Simon suggested to keep u-boot.dtb at the top directory
because it is a build output.

After discussions, we agreed on revival of ./u-boot.dtb.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>