3 years agoarm: mx6: fix cpu_rev calculation
Lothar Waßmann [Thu, 9 May 2019 13:48:22 +0000 (15:48 +0200)]
arm: mx6: fix cpu_rev calculation

3 years agoarm: mx6: implement refcounting for the ocotp clock and use 'fuse_read()' rather...
Lothar Waßmann [Thu, 9 May 2019 13:47:12 +0000 (15:47 +0200)]
arm: mx6: implement refcounting for the ocotp clock and use 'fuse_read()' rather than 'readl()' to access the HAB fuses

3 years agokaro: common: remove '_' from DT property names
Lothar Waßmann [Thu, 9 May 2019 13:41:59 +0000 (15:41 +0200)]
karo: common: remove '_' from DT property names

DT property names should not contain underscores but dashes as word
delimiters. The DT files in Linux have been updated to reflect this.
For compatibility with older DTBs support both variants of certain
property names.

3 years agokaro: tx6: make pixelclock overridable via DT or 'video_mode'
Lothar Waßmann [Thu, 9 May 2019 13:39:46 +0000 (15:39 +0200)]
karo: tx6: make pixelclock overridable via DT or 'video_mode'

3 years agokaro: txul: fix LDO4 output voltage
Lothar Waßmann [Wed, 30 Jan 2019 12:25:45 +0000 (13:25 +0100)]
karo: txul: fix LDO4 output voltage

Currently the LDO4 which supplies the pins of the CSI interface is
programmed for a voltage of 1.8V (default setting for this LDO of the
Change this to 3.3V to match the specification of the TXUL modules.
Also configure the sleep state voltages for the LDOs.

3 years agofix TXUL module name
Lothar Waßmann [Wed, 17 Oct 2018 15:46:20 +0000 (17:46 +0200)]
fix TXUL module name

4 years agokaro: tx6: enable vsnprintf for safer string operations
Lothar Waßmann [Thu, 8 Feb 2018 16:35:12 +0000 (17:35 +0100)]
karo: tx6: enable vsnprintf for safer string operations

4 years agokaro: txul: add support for TX-Tester-V5 baseboard
Lothar Waßmann [Thu, 8 Feb 2018 16:34:23 +0000 (17:34 +0100)]
karo: txul: add support for TX-Tester-V5 baseboard

4 years agokaro: txul: read second mac address from fuses
Lothar Waßmann [Thu, 8 Feb 2018 16:33:54 +0000 (17:33 +0100)]
karo: txul: read second mac address from fuses

4 years agoarm: mx6ull: initialize AIPS-TZ3 bus
Lothar Waßmann [Thu, 8 Feb 2018 16:32:36 +0000 (17:32 +0100)]
arm: mx6ull: initialize AIPS-TZ3 bus

4 years agokaro: add workaround for Linux hang on i.MX6QP when tzasc1_ipg_clock is disabled
Lothar Waßmann [Wed, 10 Jan 2018 14:19:40 +0000 (15:19 +0100)]
karo: add workaround for Linux hang on i.MX6QP when tzasc1_ipg_clock is disabled

The IPU on i.MX6QP apparently requires the tzasc1_ipg_clock
(CCGR2[11]) to be enabled which is not documented anywhere.

Enable this clock in the DCD to prevent Linux from hanging when using
the IPU.

4 years agokaro: tx6: enable raw initrd support
Lothar Waßmann [Mon, 8 Jan 2018 12:26:13 +0000 (13:26 +0100)]
karo: tx6: enable raw initrd support

4 years agokaro: bootce: suppress mtdparts related error message when CMD_MTDPARTS is not set
Lothar Waßmann [Mon, 8 Jan 2018 12:24:05 +0000 (13:24 +0100)]
karo: bootce: suppress mtdparts related error message when CMD_MTDPARTS is not set

4 years agokaro: txul: remove i2c_gpio_pads
Lothar Waßmann [Mon, 8 Jan 2018 12:21:28 +0000 (13:21 +0100)]
karo: txul: remove i2c_gpio_pads

The I2C bus for accessing the PMIC uses the soft I2C driver via GPIO
pins. There is no need for reconfiguring the pads for I2C recovery and
no need for a special i2c_gpio_pads definition.

4 years agokaro: tx6: change drive strength of Ethernet related pads to improve EMC
Lothar Waßmann [Mon, 8 Jan 2018 12:14:01 +0000 (13:14 +0100)]
karo: tx6: change drive strength of Ethernet related pads to improve EMC

EMC measurements have revealed excessive noise at multiples of the
50MHz ethernet reference clock on TX6 modules. Changing the drive
strength of the ENET_REF_CLK pad vastly reduces this noise and
improves the signal waveform substanitally.

On TXUL also the MDC and MDIO pads contribute to this noise, since
they are routed off-board for connecting an optional second ethernet
PHY. Adjusting the drive strength for those pads on the TXUL modules
also improves the signal quality and reduces EMI.

4 years agoimx: mx6: align the SPEED_MED setting with the reset default
Lothar Waßmann [Mon, 8 Jan 2018 11:47:34 +0000 (12:47 +0100)]
imx: mx6: align the SPEED_MED setting with the reset default

The PAD_CTL SPEED settings 0x1 and 0x2 both designate 'Medium
Speed'. The PAD_CTL register HW reset default value is '0x2' for
most pads, so use this value for the PAD_CTL_SPEED_MED definition.

This partially reverts commit 9b2cc7dbfd46 ("imx: mx6 add
PAD_CTL_SPEED_LOW for i.MX6SX/UL") which inadvertently changed the
definition from '2' to '1'.

4 years agokaro: tx6: indentation cleanup
Lothar Waßmann [Mon, 8 Jan 2018 11:35:36 +0000 (12:35 +0100)]
karo: tx6: indentation cleanup

4 years agokaro: tx6: cleanup i2c_recover implementation
Lothar Waßmann [Mon, 8 Jan 2018 10:25:00 +0000 (11:25 +0100)]
karo: tx6: cleanup i2c_recover implementation

Bring the tx6qdl i2c_recover implementation in sync with the tx6ul

4 years agokaro: tx6: remove duplicate initialization of ENET pads
Lothar Waßmann [Mon, 8 Jan 2018 10:22:09 +0000 (11:22 +0100)]
karo: tx6: remove duplicate initialization of ENET pads

4 years agoboard: karo: add support for using Linux simple-panel LCD driver KARO-TX6-2017-10-27
Lothar Waßmann [Wed, 25 Oct 2017 12:04:56 +0000 (14:04 +0200)]
board: karo: add support for using Linux simple-panel LCD driver

Provide support for updating the 'compatible' property of the
simple-panel DT node according to the LCD timing selected via
the 'video_mode' variable.

4 years agokaro: tx6: add support for TX6QP-8137 KARO-TX6QP-2017-07-21
Lothar Waßmann [Fri, 21 Jul 2017 11:31:09 +0000 (13:31 +0200)]
karo: tx6: add support for TX6QP-8137

TX6QP-8137 is a variant of the TX6QP-8037 module with LVDS video

4 years agokaro: tx6: prevent DTB from either being out of reach of kernel or overwritten during...
Lothar Waßmann [Fri, 21 Jul 2017 11:33:21 +0000 (13:33 +0200)]
karo: tx6: prevent DTB from either being out of reach of kernel or overwritten during uncompress

The current setting of fdtaddr and fdt_high has proven to be
inappropriate in that either the FDT may be out of reach of the
kernel or may be overwritten by the uncompressing Linux kernel.

Set fdt_high to an offset of 256MiB from SDRAM start, so that it is
valid for any board regardless of memory size while preventing the
described problems.

4 years agokaro: tx6: add support for Ka-Ro TX6UL-8013 KARO-TX6ULL-2017-07-07
Lothar Waßmann [Fri, 7 Jul 2017 14:04:39 +0000 (16:04 +0200)]
karo: tx6: add support for Ka-Ro TX6UL-8013

4 years agoarm: mx6: add support for i.MX6ULL
Lothar Waßmann [Fri, 7 Jul 2017 14:03:47 +0000 (16:03 +0200)]
arm: mx6: add support for i.MX6ULL

5 years agokaro: add support for TX6UL-5012
Lothar Waßmann [Mon, 3 Apr 2017 11:29:40 +0000 (13:29 +0200)]
karo: add support for TX6UL-5012

5 years agokaro: tx6: use GP1 fuse for MIPI variant detection KARO-TX6Q-1230_2017-01-04
Lothar Waßmann [Wed, 4 Jan 2017 08:55:52 +0000 (09:55 +0100)]
karo: tx6: use GP1 fuse for MIPI variant detection

5 years agokaro: tx6: support MIPI variant in board name KARO-TX6Q-1230-2016-12-23
Lothar Waßmann [Fri, 23 Dec 2016 11:56:32 +0000 (12:56 +0100)]
karo: tx6: support MIPI variant in board name

The TX6Q-1230 is physically the same as TX6Q-1030 with the
distinction, that the MIPI interface is used rather than the LCD
interface. This is only a cosmetic change to adjust the displayed
board name.

5 years agokaro: tx6ul: configure some more PMIC regs and disable unused DCDC2 regulator KARO-TX-2016-07-11
Lothar Waßmann [Mon, 11 Jul 2016 09:19:59 +0000 (11:19 +0200)]
karo: tx6ul: configure some more PMIC regs and disable unused DCDC2 regulator

5 years agokaro: tx6: configure PMIC to a consistent state upon boot
Lothar Waßmann [Mon, 11 Jul 2016 09:18:38 +0000 (11:18 +0200)]
karo: tx6: configure PMIC to a consistent state upon boot

5 years agokaro: tx6: fix offset voltage in formulas for calculating VDDRTC
Lothar Waßmann [Mon, 11 Jul 2016 09:01:13 +0000 (11:01 +0200)]
karo: tx6: fix offset voltage in formulas for calculating VDDRTC

5 years agokaro: tx6: remove obsolete TX6Q-1020
Lothar Waßmann [Mon, 11 Jul 2016 08:40:30 +0000 (10:40 +0200)]
karo: tx6: remove obsolete TX6Q-1020

5 years agokaro: tx6ul: fix wrong board name in U-Boot messages KARO-TX-2016-07-05
Lothar Waßmann [Tue, 5 Jul 2016 12:37:18 +0000 (14:37 +0200)]
karo: tx6ul: fix wrong board name in U-Boot messages

5 years agoMerge branch 'tx6-bugfix'
Lothar Waßmann [Mon, 4 Jul 2016 12:49:53 +0000 (14:49 +0200)]
Merge branch 'tx6-bugfix'

5 years agoMerge branch 'tx53-bugfix'
Lothar Waßmann [Mon, 4 Jul 2016 12:49:50 +0000 (14:49 +0200)]
Merge branch 'tx53-bugfix'

5 years agoMerge branch 'tx28-bugfix'
Lothar Waßmann [Mon, 4 Jul 2016 12:49:42 +0000 (14:49 +0200)]
Merge branch 'tx28-bugfix'

5 years agokaro: tx6: remove unreachable 'return' statements
Lothar Waßmann [Fri, 1 Jul 2016 14:06:24 +0000 (16:06 +0200)]
karo: tx6: remove unreachable 'return' statements

5 years agokaro: tx6: fix miscalculated start block for 'romupdate' command
Lothar Waßmann [Fri, 1 Jul 2016 14:05:58 +0000 (16:05 +0200)]
karo: tx6: fix miscalculated start block for 'romupdate' command

5 years agokaro: tx6ul: rework PMIC support and print PMIC name in boot message
Lothar Waßmann [Fri, 1 Jul 2016 14:05:15 +0000 (16:05 +0200)]
karo: tx6ul: rework PMIC support and print PMIC name in boot message

5 years agokaro: tx6ul: enable soft i2c driver and 'i2c' command
Lothar Waßmann [Fri, 1 Jul 2016 14:04:11 +0000 (16:04 +0200)]
karo: tx6ul: enable soft i2c driver and 'i2c' command

5 years agokaro: tx6ul: rework I2C recovery routine to be more generic
Lothar Waßmann [Fri, 1 Jul 2016 14:02:40 +0000 (16:02 +0200)]
karo: tx6ul: rework I2C recovery routine to be more generic

5 years agokaro: tx6ul: change local 'tx6_' prefixes to 'tx6ul'
Lothar Waßmann [Fri, 1 Jul 2016 14:01:46 +0000 (16:01 +0200)]
karo: tx6ul: change local 'tx6_' prefixes to 'tx6ul'

5 years agokaro: tx6ul: configure JTAG_* pads for JTAG function unless disabled by env. variable
Lothar Waßmann [Fri, 1 Jul 2016 14:00:55 +0000 (16:00 +0200)]
karo: tx6ul: configure JTAG_* pads for JTAG function unless disabled by env. variable

5 years agokaro: tx6: configure all pads with explicit pad_ctl values
Lothar Waßmann [Fri, 1 Jul 2016 13:41:16 +0000 (15:41 +0200)]
karo: tx6: configure all pads with explicit pad_ctl values

5 years agokaro: tx6: add TX6S LVDS module variants
Lothar Waßmann [Fri, 1 Jul 2016 12:03:48 +0000 (14:03 +0200)]
karo: tx6: add TX6S LVDS module variants

5 years agokaro: tx6: remove obsolete configs
Lothar Waßmann [Fri, 1 Jul 2016 11:41:48 +0000 (13:41 +0200)]
karo: tx6: remove obsolete configs

5 years agokaro: tx6: introduce generic TARGET_EMMC/TARGET_NAND to simplify Kconfig
Lothar Waßmann [Fri, 1 Jul 2016 11:30:48 +0000 (13:30 +0200)]
karo: tx6: introduce generic TARGET_EMMC/TARGET_NAND to simplify Kconfig

5 years agokaro: tx28: fix bugs in 'romupdate' command
Lothar Waßmann [Thu, 30 Jun 2016 13:41:36 +0000 (15:41 +0200)]
karo: tx28: fix bugs in 'romupdate' command

5 years agokaro: tx28: enable 'gpio' command
Lothar Waßmann [Thu, 30 Jun 2016 13:41:08 +0000 (15:41 +0200)]
karo: tx28: enable 'gpio' command

5 years agomxs_gpio: correctly use the GPIO API
Lothar Waßmann [Thu, 30 Jun 2016 13:40:18 +0000 (15:40 +0200)]
mxs_gpio: correctly use the GPIO API

The GPIO API expects a linear GPIO number as parameter to the gpio_*()
functions. The current implementation of the mxs_gpio driver operates on
iomux_cfg_t cookies instead. Therefore the 'gpio' command cannot be
used with this driver.
Change the driver to implement the correct API and introduce some
checks to catch users that still use the old semantics.
1. assert the most sigificant bit in the iomux_cfg_t pad definitions,
   so that using such a cookie in place of a GPIO number will
   decisively generate an invalid GPIO number and flag an error at runtime.
2. introduce a compile switch CONFIG_MXS_IOMUX_COMPILE_CHECK to make
   the iomux_cfg_t cookie a 64 bit variable, so that passing an
   iomux_cfg_t value to a gpio_*() function will generate a compile
   time error.

5 years agomxs_gpio: improve readability by using '(void *)' on right hand size of pointer initi...
Lothar Waßmann [Thu, 30 Jun 2016 10:31:42 +0000 (12:31 +0200)]
mxs_gpio: improve readability by using '(void *)' on right hand size of pointer initializations

5 years agomxs_gpio: remove unused defines
Lothar Waßmann [Thu, 30 Jun 2016 10:30:15 +0000 (12:30 +0200)]
mxs_gpio: remove unused defines

5 years agokaro: tx28: request gpio for acitivity LED and disable LED on failure
Lothar Waßmann [Thu, 30 Jun 2016 12:33:39 +0000 (14:33 +0200)]
karo: tx28: request gpio for acitivity LED and disable LED on failure

5 years agokaro: tx28: enable activity led only on stk5-v3 baseboard
Lothar Waßmann [Thu, 30 Jun 2016 10:01:49 +0000 (12:01 +0200)]
karo: tx28: enable activity led only on stk5-v3 baseboard

5 years agokaro: tx28: enable U-Boot build with different (or none) console UART
Lothar Waßmann [Thu, 30 Jun 2016 09:59:02 +0000 (11:59 +0200)]
karo: tx28: enable U-Boot build with different (or none) console UART

5 years agokaro: tx28: explicitly configure pad config (voltage, pull, drive) for all pads
Lothar Waßmann [Thu, 30 Jun 2016 09:57:39 +0000 (11:57 +0200)]
karo: tx28: explicitly configure pad config (voltage, pull, drive) for all pads

5 years agokaro: tx28: remove LCD pad configuration from SPL
Lothar Waßmann [Thu, 30 Jun 2016 09:45:52 +0000 (11:45 +0200)]
karo: tx28: remove LCD pad configuration from SPL

5 years agomxs: spl: print the actual battery brownout level rather than the constant string...
Lothar Waßmann [Thu, 30 Jun 2016 09:44:30 +0000 (11:44 +0200)]
mxs: spl: print the actual battery brownout level rather than the constant string '3.0V'

5 years agomxs: spl: adjust delay after setting CLKCTRL_PLL0CTRL0_POWER to what the hardware...
Lothar Waßmann [Thu, 30 Jun 2016 09:43:32 +0000 (11:43 +0200)]
mxs: spl: adjust delay after setting CLKCTRL_PLL0CTRL0_POWER to what the hardware requires (according to the Reference Manual)

5 years agomxs: spl: use writel() to Set/Clear registers rather than {set|clear}bits_le32()...
Lothar Waßmann [Thu, 30 Jun 2016 09:37:16 +0000 (11:37 +0200)]
mxs: spl: use writel() to Set/Clear registers rather than {set|clear}bits_le32() where applicable

5 years agomxs: spl: replace bogus early_delay() function with standard udelay() calls
Lothar Waßmann [Thu, 30 Jun 2016 09:35:07 +0000 (11:35 +0200)]
mxs: spl: replace bogus early_delay() function with standard udelay() calls

5 years agoARM: MXS: use 'struct mxs_digctl_regs' to access MXS_HW_DIGCTL_MICROSECONDS
Lothar Waßmann [Thu, 30 Jun 2016 09:32:52 +0000 (11:32 +0200)]
ARM: MXS: use 'struct mxs_digctl_regs' to access MXS_HW_DIGCTL_MICROSECONDS

5 years agokaro: tx53: enable 'gpio' command
Lothar Waßmann [Thu, 30 Jun 2016 08:46:21 +0000 (10:46 +0200)]
karo: tx53: enable 'gpio' command

5 years agokaro: tx53: romupdate: fix calculation of starting block in tx53_prog_uboot()
Lothar Waßmann [Thu, 30 Jun 2016 08:46:00 +0000 (10:46 +0200)]
karo: tx53: romupdate: fix calculation of starting block in tx53_prog_uboot()

5 years agokaro: tx53: various fixes for CONFIG_SECURE_BOOT
Lothar Waßmann [Thu, 30 Jun 2016 08:44:39 +0000 (10:44 +0200)]
karo: tx53: various fixes for CONFIG_SECURE_BOOT

5 years agofs/fs.c: correctly interpret the '(max)len' parameter to fs_read()
Lothar Waßmann [Wed, 29 Jun 2016 09:06:58 +0000 (11:06 +0200)]
fs/fs.c: correctly interpret the '(max)len' parameter to fs_read()

The 'len' parameter passed to fs_read() actually denotes the maximum
number of bytes that fit into the callers buffer, not an expected
amount of data to be read.
Rename the parameter accordingly and honor the maxlen requested by the
caller appropriately.
Also remove the bogus warning message printed when the number of bytes
read is smaller than maxlen.

5 years agocmd_gpio.c: adjust help message depending on gpio_status being compiled in or not
Lothar Waßmann [Wed, 29 Jun 2016 08:52:53 +0000 (10:52 +0200)]
cmd_gpio.c: adjust help message depending on gpio_status being compiled in or not

5 years agocommon/cmd_mtdparts.c: print ECC stats along with partition information
Lothar Waßmann [Wed, 29 Jun 2016 08:51:31 +0000 (10:51 +0200)]
common/cmd_mtdparts.c: print ECC stats along with partition information

5 years agocommon/cmd_mtdparts.c: use proper return values for U-Boot command functions
Lothar Waßmann [Wed, 29 Jun 2016 08:50:13 +0000 (10:50 +0200)]
common/cmd_mtdparts.c: use proper return values for U-Boot command functions

5 years agocommon/cmd_misc.c: fix return code of sleep command
Lothar Waßmann [Wed, 29 Jun 2016 08:46:49 +0000 (10:46 +0200)]
common/cmd_misc.c: fix return code of sleep command

-1 is equivalent to CMD_RET_USAGE and makes the sleep command print
its usage information when aborted by <CTRL-C> which is most probably
not intended.

6 years agoMerge branch 'tx28-update' into tx28-bugfix
Lothar Waßmann [Mon, 13 Jun 2016 10:19:11 +0000 (12:19 +0200)]
Merge branch 'tx28-update' into tx28-bugfix

6 years agokaro: tx6ul: disable the PMIC for '_noenv' U-Boot KARO-TX6-2016-04-26
Lothar Waßmann [Tue, 26 Apr 2016 13:33:34 +0000 (15:33 +0200)]
karo: tx6ul: disable the PMIC for '_noenv' U-Boot

The I2C access to the PMIC requires the TAMPER pins of the i.MX6UL to
be useable as GPIOs. This is only possible after the TAMPER_PIN_DISABLE
fuses are programmed which is usually done via U-Boot.
Resolve this catch 22 situation by disabling the PMIC in the '_noenv'
U-Boot variant which is usually used in the manufacturing

6 years agokaro: tx6ul: make board string dependent on cpurev
Lothar Waßmann [Tue, 26 Apr 2016 13:30:56 +0000 (15:30 +0200)]
karo: tx6ul: make board string dependent on cpurev

6 years agomx6: clock: use setup_gpmi_io_clk() to change nfc clk divider for CONFIG_NAND_MXS
Lothar Waßmann [Tue, 26 Apr 2016 13:29:48 +0000 (15:29 +0200)]
mx6: clock: use setup_gpmi_io_clk() to change nfc clk divider for CONFIG_NAND_MXS

6 years agomx6: clock: fix integer overflow in calculation of relative error in set_nfc_clk()
Lothar Waßmann [Tue, 26 Apr 2016 13:20:19 +0000 (15:20 +0200)]
mx6: clock: fix integer overflow in calculation of relative error in set_nfc_clk()

6 years agomx6: ocotp: add timeout to busy wait loop
Lothar Waßmann [Tue, 26 Apr 2016 13:19:20 +0000 (15:19 +0200)]
mx6: ocotp: add timeout to busy wait loop

6 years agokaro: tx6: pmic: print PMIC name in boot messages
Lothar Waßmann [Tue, 26 Apr 2016 13:16:57 +0000 (15:16 +0200)]
karo: tx6: pmic: print PMIC name in boot messages

6 years agoarm: mx6: fix NFC clock get/set routines for i.MX6QP,i.MX6UL tx6qp-devel
Lothar Waßmann [Tue, 19 Apr 2016 14:07:37 +0000 (16:07 +0200)]
arm: mx6: fix NFC clock get/set routines for i.MX6QP,i.MX6UL

6 years agokaro: tx6: add support for TX6Q-8037 (i.MX6QP)
Lothar Waßmann [Mon, 18 Apr 2016 12:45:01 +0000 (14:45 +0200)]
karo: tx6: add support for TX6Q-8037 (i.MX6QP)

6 years agokaro: tx6: add support for boards with >= 2GiB memory
Lothar Waßmann [Mon, 18 Apr 2016 12:43:29 +0000 (14:43 +0200)]
karo: tx6: add support for boards with >= 2GiB memory

6 years agokaro: tx6: disable gpmi clk before changing podf and clk_sel
Lothar Waßmann [Mon, 18 Apr 2016 12:42:17 +0000 (14:42 +0200)]
karo: tx6: disable gpmi clk before changing podf and clk_sel

6 years agokaro: tx6: replace open coded interpretation of cpurev by calls to is_cpu_type()
Lothar Waßmann [Mon, 18 Apr 2016 07:43:23 +0000 (09:43 +0200)]
karo: tx6: replace open coded interpretation of cpurev by calls to is_cpu_type()

6 years agokaro: tx6: set LCD x, y dimensions to 0 when disabling LCD
Lothar Waßmann [Mon, 18 Apr 2016 07:33:43 +0000 (09:33 +0200)]
karo: tx6: set LCD x, y dimensions to 0 when disabling LCD

Even when the LCD is disabled, the LCD framework will still clear the
video memory. This can take a cosiderable amount of time for the
maximum resolution of 16MiB that the i.MX6 supports.

Setting vl_row and vl_col to 0 results in a zero sized framebuffer
to avoid this unnecessary delay.

6 years agokaro: tx6: rename CONFIG_SYS_BOOT_CMD_NAND to FDTSAVE_CMD_STR
Lothar Waßmann [Mon, 18 Apr 2016 07:30:59 +0000 (09:30 +0200)]

This macro in not actually a configurable setting as the original
naming suggests.

6 years agomx6: clock: take 'num' and 'denom' regs into account when calculating audio/video...
Lothar Waßmann [Wed, 13 Apr 2016 10:03:10 +0000 (12:03 +0200)]
mx6: clock: take 'num' and 'denom' regs into account when calculating audio/video PLL frequency

6 years agonet: fec: use correct sizes to clear and flush descriptors
Lothar Waßmann [Wed, 13 Apr 2016 10:00:52 +0000 (12:00 +0200)]
net: fec: use correct sizes to clear and flush descriptors

6 years agorename TX6Q-1033 to TX6Q-1036
Lothar Waßmann [Wed, 13 Apr 2016 09:17:12 +0000 (11:17 +0200)]
rename TX6Q-1033 to TX6Q-1036

6 years agokaro: tx28: supply a valid stack pointer to early SPL code
Lothar Waßmann [Thu, 24 Mar 2016 11:30:01 +0000 (12:30 +0100)]
karo: tx28: supply a valid stack pointer to early SPL code

6 years agokaro: tx28: remove obsolete u-boot.bd
Lothar Waßmann [Thu, 24 Mar 2016 11:28:21 +0000 (12:28 +0100)]
karo: tx28: remove obsolete u-boot.bd

6 years agomxs: spl: remove duplicate debug messages
Lothar Waßmann [Thu, 24 Mar 2016 11:01:02 +0000 (12:01 +0100)]
mxs: spl: remove duplicate debug messages

6 years agokaro: tx6: remove redundant #ifndef CONFIG_TX6_UBOOT_MFG
Lothar Waßmann [Fri, 18 Mar 2016 09:35:26 +0000 (10:35 +0100)]
karo: tx6: remove redundant #ifndef CONFIG_TX6_UBOOT_MFG

6 years agoMerge branch 'tx53-update-2016-02-03' into karo-tx6 KARO-TX6-2016-03-10
Lothar Waßmann [Thu, 18 Feb 2016 17:38:00 +0000 (18:38 +0100)]
Merge branch 'tx53-update-2016-02-03' into karo-tx6

6 years agoMerge branch 'tx28-update-2016-02-03' into karo-tx6
Lothar Waßmann [Thu, 18 Feb 2016 17:37:47 +0000 (18:37 +0100)]
Merge branch 'tx28-update-2016-02-03' into karo-tx6

6 years agoMerge branch 'tx6-update-2016-02-03' into karo-tx6
Lothar Waßmann [Thu, 18 Feb 2016 17:37:33 +0000 (18:37 +0100)]
Merge branch 'tx6-update-2016-02-03' into karo-tx6

6 years agokaro: tx6ul: fix bogus GPIO numbers
Lothar Waßmann [Thu, 18 Feb 2016 17:36:01 +0000 (18:36 +0100)]
karo: tx6ul: fix bogus GPIO numbers

6 years agokaro: tx6ul: add pad settings for FT5x06 and USB pads on STK5
Lothar Waßmann [Thu, 18 Feb 2016 17:35:38 +0000 (18:35 +0100)]
karo: tx6ul: add pad settings for FT5x06 and USB pads on STK5

6 years agokaro: tx6ul: add support for TX6UL Mainboard (v1)
Lothar Waßmann [Thu, 18 Feb 2016 17:34:32 +0000 (18:34 +0100)]
karo: tx6ul: add support for TX6UL Mainboard (v1)

6 years agokaro: tx6ul: defer mmc probing until environment has been loaded
Lothar Waßmann [Thu, 18 Feb 2016 17:30:19 +0000 (18:30 +0100)]
karo: tx6ul: defer mmc probing until environment has been loaded

Check the 'baseboard' environment variable before initializing the MMC
interface to prevent error messages on TX6UL-Mainboard which doesn't
support MMC mass storage.

6 years agokaro: tx6ul: proper initialize second FEC if available
Lothar Waßmann [Thu, 18 Feb 2016 17:29:21 +0000 (18:29 +0100)]
karo: tx6ul: proper initialize second FEC if available

6 years agokaro: tx6ul: reorder functions to better follow which ones are called with the defaul...
Lothar Waßmann [Thu, 18 Feb 2016 17:27:36 +0000 (18:27 +0100)]
karo: tx6ul: reorder functions to better follow which ones are called with the default resp. loaded environment

6 years agokaro: tx6: check ctrlc before returning error code for unsupported baseboard
Lothar Waßmann [Thu, 18 Feb 2016 17:18:43 +0000 (18:18 +0100)]
karo: tx6: check ctrlc before returning error code for unsupported baseboard