Paul Burton [Mon, 7 Apr 2014 15:41:47 +0000 (16:41 +0100)]
pcnet: align rx buffers for cache invalidation
The RX buffers are invalidated when a packet is received, however they
were not suitably cache-line aligned. Allocate them seperately to the
pcnet_priv structure and align to ARCH_DMA_MINALIGN in order to ensure
suitable alignment for the cache invalidation, preventing anything else
being placed in the same lines & lost.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The prior accesses to the descriptor rings & init block via cached
memory had a few issues:
- The memory needs cache flushes or invalidation at the appropriate
times, but was not necessarily aligned on cache line boundaries.
This could lead to data being incorrectly lost or written back to
RAM at the wrong time.
- There are points where ordering of writes to the memory is
important, but because it's cached memory the pcnet controller
would see cache lines written back ordered by address. This could
occasionally lead to hardware seeing descriptors in an incorrect
state.
- Flushing the cache constantly is inefficient.
So, to avoid all of those issues simply access the descriptors & init
block via uncached memory. The MIPS-specific UNCACHED_SDRAM macro is
used to do this (retrieving an address in kseg1) as I could see no
existing generic solution. Since the MIPS Malta board is the only user
of the pcnet driver, hopefully this doesn't matter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
doc:power:pmic: Add doc entry for PMIC(v2) framework
Well written documentation for PMIC framework was missing and hence
it has been probably difficult and time consuming for other developers
to understand rationale for key design decisions and overall design
structure.
This commit provides proper documentation entry.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/genietv/*
- Remove include/configs/GENIETV.h
- Clean-up if defined(CONFIG_GENIETV)
- Move the entry from boards.cfg to doc/README.scrapyard
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Ian Campbell [Thu, 27 Mar 2014 20:34:13 +0000 (20:34 +0000)]
blackfin: make name_to_gpio be a weak symbol
This required moving it into a C file from the header.
The only user of a non-default name_to_gpio is blackfin, therefore build tested
with the blackfin bct-brettl2 build, which is one I picked at random. Also
tested with a build for the ARM tec board which uses the default/fallback
implementation. Inspection with objdump shows that both have done the right
thing.
This change was requested by Marek during review of the sunxi patch series.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Sonic Zhang <sonic.adi@gmail.com>
Tom Rini [Wed, 9 Apr 2014 12:25:57 +0000 (08:25 -0400)]
am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOT
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.
Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Wolfgang Denk <wd@denx.de>
omap3: zoom1: switch to generic ti_omap3_common config header
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Multicore navigator consists of Network Coprocessor (NetCP) and
Queue Manager sub system. More details on the hardware can
be obtained from the following links:-
spi: davinci: add support for multiple bus and chip select
Currently davinci spi driver supports only bus 0 cs 0.
This patch allows driver to support bus 1 and bus 2 with
configurable number of chip selects. Also defaults are
selected in a way to avoid regression on other platforms
that uses davinci spi driver and has only one spi bus.
Signed-off-by: Rex Chang <rchang@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
i2c, davinci: move i2c_defs.h to the drivers/i2c directory
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.
Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.
This patch add support for gpimage format as a preparatory
patch for porting u-boot for keystone2 devices and is
based on omapimage format. It re-uses gph header to store the
size and loadaddr as done in omapimage.c
fdt: call ft_board_setup_ex() at the end of image_setup_libfdt()
The keystone2 SOC requires to fix all 32 bit aliased addresses
to their 36 physical format. This has to happen after all fdt
nodes are added or modified.
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 17 Apr 2014 21:23:25 +0000 (17:23 -0400)]
am335x_evm: Drop SPI SPL support from the default build
This is only useful with the _spiboot build target anyhow, so only
include it then. Drop CONFIG_SPL_OS_BOOT support then as the flash is
small and didn't include a spot for the device tree already.
Tom Rini [Thu, 3 Apr 2014 11:52:53 +0000 (07:52 -0400)]
TI:armv7: Change Falcon Mode DT load address
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree. In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Tom Rini [Fri, 28 Mar 2014 19:03:29 +0000 (15:03 -0400)]
TI: Add, use a DEFAULT_LINUX_BOOT_ENV environment string
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Tom Rini [Fri, 28 Mar 2014 16:03:42 +0000 (12:03 -0400)]
spl_mmc/CONFIG_SPL_OS_BOOT: Allow environment to determine what to boot
We add two new environment variables, falcon_args_file and
falcon_image_file, which when set will override the compiled in default
values for falcon mode.
Tom Rini [Fri, 28 Mar 2014 16:03:38 +0000 (12:03 -0400)]
am335x_evm: Make SPL_OS also check the boot_os variable for falcon mode
We use the same variable as a3m071 in the environment to determine if we
should boot into Linux or U-Boot. This is useful on boards like
Beaglebone Black or AM335x GP EVM where we have persistent storage for
the environment.
Tom Rini [Fri, 28 Mar 2014 16:03:34 +0000 (12:03 -0400)]
env_mmc.c: Allow environment to be used within SPL
Inside of SPL we only concern ourself with one MMC device, so instead of
being able to use CONFIG_SYS_MMC_ENV_DEV we need to use 0 in SPL.
Switch the code to use a 'dev' variable to facilitate this.
Tom Rini [Fri, 28 Mar 2014 16:03:33 +0000 (12:03 -0400)]
fw_env.c: Switch get_config to use '%ms' in sscanf
We currently limit ourself to 16 characters for the device name to read
the environment from. This is insufficient for /dev/mmcblk0boot1 to
work for example. Switch to '%ms' which gives us a dynamically
allocated buffer instead. We're short lived enough to not bother
free()ing the buffer.
Nishanth Menon [Fri, 28 Mar 2014 16:00:06 +0000 (11:00 -0500)]
OMAP3: beagle-xm: generate fake USB ethernet MAC address from dieid
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Nishanth Menon [Fri, 28 Mar 2014 16:00:04 +0000 (11:00 -0500)]
OMAP: common: consolidate fake USB ethernet MAC address creation
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Wolfgang Denk [Tue, 25 Mar 2014 13:49:50 +0000 (14:49 +0100)]
ARM: OMAP: replace custom sr32() by standard I/O accessors
Replace the custom bit manipulation function sr32() by standard I/O
accessors. A major motivation for this cleanup was the fact, that a
number of calls of that function resulted in 32 bit wide shift
operations on u32 data, which according to the C-ISO/IEC-9899-Standard
provokes undefined behaviour:
6.5.7 Bitwise shift operators
...
If the value of the right operand is negative or is greater
than or equal to the width of the promoted left operand, the
behavior is undefined.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Wolfgang Denk [Tue, 25 Mar 2014 13:49:49 +0000 (14:49 +0100)]
ARM: OMAP: hide custom bit manipulation function sr32()
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in
that file to prepare complete removal.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Masahiro Yamada [Mon, 31 Mar 2014 03:59:58 +0000 (12:59 +0900)]
board: esd: remove remainders of dead boards
Commit 99bcad18 deleted ADCIOP and DASA_SIM board support
but missed to delete board/esd/adciop and board/esd/dasa_sim.
It also missed to add entries to doc/README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Stephen Warren [Fri, 21 Mar 2014 21:58:03 +0000 (15:58 -0600)]
ARM: tegra: pack pinmux data tables tighter
Use smaller fields in the Tegra pinmux structures in order to pack the
data tables into a smaller space. This saves around 1-3KB for the SPL
and around 3-8KB for the main build of U-Boot, depending on the board,
which SoC it uses, and how many pinmux table entries there are.
In order to pack PMUX_FUNC_* into a smaller space, don't hard-code the
values of PMUX_FUNC_RSVD* to values which require 16 bits to store them,
but instead let their values be assigned automatically, so they end up
fitting into 8 bits.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Sun, 2 Mar 2014 18:46:50 +0000 (19:46 +0100)]
usb: tegra: combine header file
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.
Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Sun, 2 Mar 2014 18:46:49 +0000 (19:46 +0100)]
usb: tegra: fix PHY configuration
On Tegra30 and later, the PTS (parallel transceiver select) and STS
(serial transceiver select) are part of the HOSTPC1_DEVLC_0 register
rather than PORTSC1_0 register. Since the reset configuration
usually matches the intended configuration, this error did not show
up on Tegra30 devices.
Also use the slightly different bit fields of first USB, (USBD) on
Tegra20 and move those definitions to the Tegra20 specific header
file.
Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Sun, 2 Mar 2014 18:46:48 +0000 (19:46 +0100)]
usb: tegra: fix USB2 powerdown for Tegra30 and later
Clear the forced powerdown bit in the UTMIP_PLL_CFG2_0 register
which brings USB2 in UTMI mode to work. This was clearly missing
since the forced powerdown bit is set in reset by default for all
USB ports.
Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:29:01 +0000 (12:29 -0600)]
ARM: tegra: Tegra124 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra124_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
There are differences in the set of drive groups. I have validated this
against the TRM. There are differences order of pin definitions in
pinmux.c; these previously had significant mismatches with the correct
order:-( I adjusted a few entries in pinmux-config-venice2.h since the
set of legal functions for some pins was updated to match the TRM.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:29:00 +0000 (12:29 -0600)]
ARM: tegra: Tegra114 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra114_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted a few entries in
pinmux-config-dalmore.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:28:59 +0000 (12:28 -0600)]
ARM: tegra: Tegra30 pinmux cleanup
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:28:56 +0000 (12:28 -0600)]
ARM: tegra: pinmux naming consistency fixes
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
compiles. A separate per-SoC change will be made immediately following,
in order to keep individual patch size down.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:28:55 +0000 (12:28 -0600)]
ARM: tegra: reduce public pinmux API
Remove a few unused functions from the pinmux header. They aren't
currently used, and removing them prevents any new usage from appearing.
This will ease moving to just pinmux_config_table() and
padgrp_config_table() in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:28:54 +0000 (12:28 -0600)]
ARM: tegra: pinctrl: remove duplication
Much of arch/arm/cpu/tegra*-common/pinmux.c is identical. Remove the
duplication by creating pinmux-common.c for all the identical code.
This leaves:
* arch/arm/include/asm/arch-tegra*/pinmux.h defining only the names of
the various pins/pin groups, drive groups, and mux functions.
* arch/arm/cpu/tegra*-common/pinmux.c containing only the lookup table
stating which pin groups support which mux functions.
The code in pinmux-common.c is semantically identical to that in the
various original pinmux.c, but had some consistency and cleanup fixes
applied during migration.
I removed the definition of struct pmux_tri_ctlr, since this is different
between SoCs (especially Tegra20 vs all others), and it's much simpler to
deal with this via the new REG/MUX_REG/... defines. spl.c, warmboot.c,
and warmboot_avp.c needed updates due to this, since they previously
hijacked this struct to encode the location of some non-pinmux registers.
Now, that code simply calculates these register addresses directly using
simple and obvious math. I like this method better irrespective of the
pinmux code cleanup anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 21 Mar 2014 18:28:53 +0000 (12:28 -0600)]
ARM: tegra: use apb_misc.h in more places
Tegra's "APB misc" register region contains various miscellaneous
registers and the Tegra pinmux registers. Some code that touches the
misc registers currently uses struct pmux_tri_ctlr, which is intended to
be a definition of pinmux registers, rather than struct apb_misc_pp_ctrl,
which is intended to be a definition of the miscellaneous registers.
Convert all such code to use struct apb_misc_pp_ctrl, since struct
pmux_tri_ctlr goes away in the next patch.
This requires adding a missing field definition to struct
apb_misc_pp_ctrl, and moving the header into a more common location.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
projects / karo-tx-uboot.git / log